• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.2
• /
• pp.285-297
• /
• 2015

In this paper, Ulta-WideBand (UWB) channel measurement and modeling based on compressive sampling (CS) are proposed. The sparsity of the channel impulse response (CIR) of the UWB signal in frequency domain enables the proposed channel measurement to have a low-complexity and to provide a comparable performance compared with the existing approaches especially used for the indoor geo-localization purpose. Furthermore, to improve the performance under noisy situation, the soft thresholding method is also investigated in solving the optimization problem for signal recovery of CS. Via numerical results, the proposed channel measurement and modeling are evaluated with the real measured data in terms of location estimation error, bandwidth, and compression ratio for indoor geo-localization using UWB system.

• Journal of Advanced Navigation Technology
• /
• v.21 no.1
• /
• pp.43-49
• /
• 2017

Generally, loop filter based scalar tracking loops (LF-STL) have been used for global positioning system (GPS) signal tracking algorithm. This paper introduces the accuracy and robustness of linear-quadratic-Gaussian based vector tracking loop (LQG-VTL) algorithm instead of LF-STL. To verify the accuracy of LQG-VTL, we confirm that the measurements estimation errors of the LQG based scalar tracking loops (LQG-STL) are improved by more than 60 % compared to LF-STL. Also, when LQG-VTL is used, measurements estimation errors decrease compared to LQG-STL, and position/velocity estimation errors also decrease as the number of satellites increases. To verify the robustness of LQG-VTL, we confirm that LQG-VTL can estimate position/velocity and measurements successively compared to LF-STL in temporal signal attenuation of 30 dB-Hz during 4 seconds.

• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.36-43
• /
• 2010

A GEO satellite launched by Arian 5 ECA launcher will be located in a transfer orbit where it requires several Apogee burn maneuvers to reach the target orbit. To obtain the required performance of Apogee burn maneuvers, a calibration of gyro drift error needs to be performed before each maneuver. In this paper, a unique gyro calibration scheme which is applied to COMS is described and the calibration error budget analysis is performed.

• Journal of IKEEE
• /
• v.9 no.1 s.16
• /
• pp.7-18
• /
• 2005

A key component of an autonomous mobile robot is to localize itself accurately and build a map of the environment simultaneously. In this paper, we propose a vision-based mobile robot localization and mapping algorithm using scale-invariant features. A camera with fisheye lens facing toward to ceiling is attached to the robot to acquire high-level features with scale invariance. These features are used in map building and localization process. As pre-processing, input images from fisheye lens are calibrated to remove radial distortion then labeling and convex hull techniques are used to segment ceiling region from wall region. At initial map building process, features are calculated for segmented regions and stored in map database. Features are continuously calculated from sequential input images and matched against existing map until map building process is finished. If features are not matched, they are added to the existing map. Localization is done simultaneously with feature matching at map building process. Localization. is performed when features are matched with existing map and map building database is updated at same time. The proposed method can perform a map building in 2 minutes on $50m^2$ area. The positioning accuracy is ${\pm}13cm$, the average error on robot angle with the positioning is ${\pm}3$ degree.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.148-155
• /
• 2021

As robot technology advances, research on the driving system of mobile robots is actively being conducted. The driving system of a mobile robot configured based on two-wheels and four-wheels has an advantage in unidirectional driving such as a straight line, but has disadvantages in turning direction and rotating in place. A ball robot using a ball as a wheel has an advantage in omnidirectional movement, but due to its structurally unstable characteristics, balancing control to maintain attitude and driving control for movement are required. By estimating the position from an encoder attached to the motor, conventional ball robots have a limitation, which causes the accumulation of errors during driving control. In this study, a driving control system was proposed that estimates the position coordinates of a ball robot through image processing and uses it for driving control. A driving control system including an image processing unit, a communication unit, a display unit, and a control unit for estimating the position of the ball robot was designed and manufactured. Through the driving control experiment applying the driving control system of the ball robot, it was confirmed that the ball robot was controlled within the error range of ±50.3mm in the x-axis direction and ±53.9mm in the y-axis direction without accumulating errors.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.4
• /
• pp.299-306
• /
• 2003

The rotor flux position is needed to perform vector control of induction motor. But rotor speed information is needed to get accurate the rotor flux position. It is difficult to implement the open loop method without speed information or the motor equation only because of noise or the motor parameter error. This paper presents the speed estimator can use the arbitrary rotor flux observer by separating the flux observer and speed estimator and apply the three flux observers proposed by Ohtani, Lorenz and full order flux observer. The validity of speed estimator presented is verified and the performance using the three rotor flux observers is analyzed by the simulation and experiment.

• Proceedings of the KIEE Conference
• /
• 2007.10a
• /
• pp.65-66
• /
• 2007

본 논문은 파라미터 변동에 잘 적응하며 강인한 영구자석 동기전동기의 위치센서 없는 센서리스 제어를 위해 개선된 슬라이딩 모드 관측기에 고정자 저항 추정기능을 추가한 새로운 슬라이딩 모드 적응 관측기를 제안한다. 제안된 관측기는 개선된 슬라이딩 모드 관측기를 사용함으로써 기존의 슬라이딩 모드 관측기에서 채터링(Chattering) 문제 해결을 위해 저역통과필터(Low-pass filter)의 사용 및 추가적인 회전자의 위치보상은 Sigmoid 함수를 스위칭 함수로 사용하므로 제거 할 수가 있다. 또한 고정자 저항 추정기능을 추가하여 센서리스 운행 중 환경적 요인으로 인한 고정자 저항값의 변동이나 초기에 고정자 저항값을 잘못 알고 있더라도 빠른 적응을 통해서 추정오차를 절감시켜 전동기의 속도추정 성능을 향상시킬수 있다. 또한 기존의 적응 슬라이딩 모드 관측기에서의 적분연산을 줄임으로써 제어시스템의 성능을 개선시켰다 제안된 관측기의 안정성은 Lyapunov 후보 함수를 이용하여 관측기의 이득을 설정함으로써 검증하였으며 관측기의 성능은 시뮬레이션을 통한 실험을 통하여 그 타당성을 입증하였다.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.4
• /
• pp.86-93
• /
• 2011

The ship movement implies current position, wave, wind, and its other factors. We need to know exactly the location and the shape of the ship and control its motion because of these effects. In order to control the small ship according to the movement of the large ship, the position and shape of the ship should be given first. In this paper we propose the method with which we know the current status of the ship without dynamic equations of the ship. There are several methods to track the system such as optical, radio frequency, radar, camera, and infrared light. We propose the movement of the ship using the GPS absolute axis. But, the genuine error by the GPS itself and the movement of the ship cause the result of the GPS of not being accurate. This paper reduces the error of the location and the shape of the ship and gives the exact values of the ship movements even if the GPS implies some error itself.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2009.01a
• /
• pp.313-320
• /
• 2009

본 논문은 옥내 이동객체 데이터베이스의 갱신 전략을 제안한다. 제안하는 방법은 최근의 일련의 측정치에 칼만 필터를 적용하여 이동객체의 속도를 예측하고, 예측한 속도를 최근 측정치에 적용하여 현재 위치를 추정한다. 그리고 현재 위치로 추정된 값과 현재 실측값의 차이가 일정 거리 이하이면 실측값을 전송하지 않는다. 제안하는 방법의 효율성을 검증하기 위하여 실험 공간을 실제로 걸어가면서 측정한 일련의 측정치에 제안하는 방안을 적용하여 전송을 절약하는 비율과 이로 인한 오차의 증가율을 분석한다.

• Information and Communications Magazine
• /
• v.31 no.2
• /
• pp.44-51
• /
• 2014

본 논문에서는 초다시점 (Super Multi-view) 영상 합성을 위한 영상 기반의 온라인 삼차원 복원 기술들을 소개한다. 복원의 정확성을 높이고자 하는 방법은 크게 두 부류로 나뉜다. 먼저 재투영 오차를 비용 함수(Cost function)으로 정의하고, 이를 Bundle Adjustment로부터 최적화를 수행하는 방법과 카메라의 위치와 삼차원 복원 결과에 대해 확률적인 분포를 정의하고 이를 순차적으로 추정하는 확률적인 필터링(Stochastic filtering)에 기반한 방법이 존재한다. 본 논문에서는 두 방법의 장단점을 분석하고, 이로부터 새로운 확률적 필터링에 기반한 3차원 복원 및 카메라 위치 추정 방법을 제안한다. 이로부터 대공간 환경에 적용하여 성능을 검증한다.