• The Journal of the Acoustical Society of Korea
• /
• v.17 no.2
• /
• pp.71-78
• /
• 1998

와(vortex) 박리는 고형물체가 유동내에서의 유체의 흐름을 방해할 때 발생하는 전 형적인 주기적 진동 현상이다. 본 연구에서는 삼각주형 실린더가 유동내에 유발하는 와 발 리 특성을 가시화 기법, 와에 의해 변조된 초음파의 파워 스펙트럼 및 유동관에서의 진동측 정 등을 통해 연구하였다. 가시화 관찰과 유동측정 실험 결과, 발생 와는 발생체 전면으로부 터 3d와 5d 사이에서 가장 안정성이 유지됨을 발견하였다. 넓은 레이놀즈 수(104≤Re≤106) 의 유동영역에서 액체와 기체원형유동의 측정 실험결과로부터 스트로우할(Strouhal) 수가 와발생체 폭(d)과 형상비(d/D)의 증가함수이며, 삼각주 단면의 높이에 반비례함을 알 수 있 었다. 또한 실험 결과로부터 실린더의 기하학적 치수로 삼각주형 실린더의 스트로우할 수를 예측할 수 있는 경험식을 제시하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.14-14
• /
• 1999

액체 램제트 엔진의 특성은 흡입구를 통해 들어오는 유입공기의 상태에 따라 많이 달라진다. 흡입구에 들어오는 공기의 유입각이 일정각도를 넘어서면 유입공기의 왜곡이 심하여 정상적인 연소가 불가능 할 수 있다. 따라서 다양한 비행조건에 따른 램제트 엔진의 특성을 파악하기 위하여 외부 유입영역, 흡입구, 연소기, 노즐 및 출구 대기 영역을 함께 계산하여 유동 특성과 연소 특성을 파악하고자 하였다. 흡입구는 마하 2.0을 기준으로 설계하고, 4각 덕트에서 완만하게 원형 덕트로 변화되는 확대관의 형상으로 비행체에 붙어 있는 것으로 격자를 구성하였다. 흡입구에서의 유동 조건은 비행체을 지난 유속이 마하 2.0과 2.2의 경우에 대하여 수치 실험을 수행하였으며, 비반응 유동 해석과 연소가 있는 반응 유동해석 결과를 흡입구를 포함하지 않았던 선행 연구 결과들과 비교하였다. 유입각이 영 일 때의 흡입구를 포함한 계산 결과는 흡입구에서 생성되는 충격파에 의한 손실로 총압력이 흡입구를 포함하지 않았던 선행 연구 결과와 차이가 있었으나 유동 특성에는 큰 차이가 없었다. 그러나 유입각이 증가함에 따라 흡입구로 유입되는 공기의 량이 감소하고 그에 따른 유동의 왜곡이 심하여 연소특성에 변화를 보여 주었다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.2
• /
• pp.267-278
• /
• 1996

Steady, laminar, forced convection flow and heat transfer in the entrance region of an internally finned circular duct with a finite thermal conductivity has been analyzed numerically. The problem under investigation is a three-dimensional boundary layer problem, and is solved by employing a marching-type procedure which involves solution of a series of 2-dimensional elliptic problems in the cross-stream plane. Two types of inlet hydrodynamic conditions are considered : (a) uniform velocity flow and (b) fully developed flow. From the above inlet conditions, the effects of the fin height(h), fin number(N) and conductivity ratio($k_r$) on the flow and thermal characteristics are investigated. The numerical results show that the height and number of fins, and ratio of the solid to fluid thermal conductivity have pronounced effect on the solution. Considering pressure drop, optimized dimensionless fin height is 0.4.

• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.314-322
• /
• 2003

Pipe cooling method is widely used for reduction of hydration heat and control of cracking in mass concrete structures. However, in order to effectively apply pipe cooling systems to concrete structures, the coefficient of flow convection relating the thermal transfer between inner stream of pipe and concrete must be estimated. In this study, a device measuring the coefficient of flow convection was developed. Since a variation of thermal distribution caused by pipe cooling has a direct effect on internal forced flows, the developed testing device is based on the internal forced flow concept. Influencing factors on the coefficient of flow convection are mainly flow velocity, pipe diameter and thickness, and pipe material. Using experimental results from the developed device, the coefficient of flow convection was calculated. Finally, a general prediction model was proposed by theoretical procedures. The proposed prediction model is able to estimate the coefficient of flow convection with flow velocity and material properties of pipe. From comparison with experimental results, the coefficient of flow convection by this model was well agreed with those by experimental results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.1
• /
• pp.33-45
• /
• 1997

Axisymmetric shear layers around a free jet is forced by co-flowing and counter-flowing secondary jets from/to an annular tube around the jet nozzle. The jet potential core extends far downstream with co-flowing secondary jets due to inhibited vortex developing and pairing. For counter-flowing cases, the axisymmetric shear layer around the jet transits from convective instability to absolute instability for velocity ratios R＝1.3～l.65 for the uniform velocity jets. Consequently, the jet potential core length increases and the turbulence level in the jet core is reduced significantly. The jets are controlled better with extension collars attached to the outer nozzle exit because the annular secondary flow is guided well by the extension collars. For the vectoring of jet, the annular tube around the jet is divided in two parts and the only one part is used for suction. The half suction makes the different shear layer around the jet and vectoring the jet by Coanda effect. The vectoring and turbulent components are varied significantly by the suction ratio. The experiments are carried out to investigate the characteristics of forced free jets using flow visualization, velocity and turbulence measurements.

• Journal of Convergence for Information Technology
• /
• v.9 no.12
• /
• pp.147-156
• /
• 2019

Numerical study was performed to investigate the convective heat transfer of Al₂O₃/water nanofluid flowing through the concentric double pipe counterflow heat exchangers. Hot fluid flowing through the inner pipe transfers its heat to cooling fluid flowing in the outer pipe. Effects of important parameters such as hot and cold volume flow rates, fluid type in the outer and inner pipes, and nanoparticles concentration on the heat transfer and flow characteristics are investigated. The results indicated that the heat transfer performance increases with increasing the hot and cold volume flow rates, as well as the particle concentrations. When both outer and inner pipes are nanofluids with 8% nanoparticle volume concentration, nanofluids showed up to 17% better heat transfer rate than basic fluids. Also, the average heat transfer coefficient of the base fluid for annulus-side improved by 31%. Approximately 20% enhancement in the heat exchanger effectiveness can be achieved with the addition of 8% alumina particles in base fluid. But, addition of nanoparticles to the base fluid enhanced friction factor by about 196%.

• Journal of the Korean Society of Visualization
• /
• v.8 no.3
• /
• pp.12-21
• /
• 2010

Swirling flows are found in very wide range of applications, for examples, cyclone separators, spraying machines, heat exchangers and jet pumps, ect. Relatively, little work has been done on the swirl flow using flow visualization techniques. This study deals with many visualization techniques to study on swirling flow. These techniques are related to oil films methods, smoke, dye liquids, liquid crystal, stroboscope light, smoke wire, white light, naphthalene sublimation, LDV(lase doppler Velocimetry) and PIV(particle image velocimetry). The present work has handled single, annular, carved tube, swirl expansion and swirl wake using several visualization methods in the vertical and horizontal circular tube.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.2
• /
• pp.147-159
• /
• 1982

내부에 정방형, 외부에 원형인 두 정온동심수평관으로 이루어진 폐쇄공간에서 열부력으로 야기된 대류열전달 현상을 연구하였다. 주어진 비정규적 형상에서의 층류 정상 Boussinesq 유동을 해 석하기 위하여, 지구중력방향에 대하여 가능한 두 개의 대칭형 위치에 관하여, Galerkin 유한요 소법을 사용하였다. 이론의 결과를 확증하기 위하여 실험적으로도 온도측정과 유선의 가시화를 수행하였다. 정방형내관의 직각인 선단은 국소 및 총체열전달에 있어서 소극적인 역할을 하지만, 이들로 인한 경계층 유동의 박리는 발생하지 아니함을 보였다. 이 내관의 상부 수평면상에서는 유동속도와 온도구배가 낮기는 하나 확연한 대칭형의 열상승류(Plume)가 가능하였다. 내관의 벽면들이 지구중력방향에 관하여 .+-.45.deg.의 각을 이룰 경우 과류의 중심부가, Rayleigh수가 6.5*$10^{4}$보다 작을 때는 4개, 이보다 클때는 2개가 폐쇄공간 안에서 발생하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.3
• /
• pp.313-318
• /
• 2012

In CANDU, feeder pipes supply heavy water to pressure tube and steam generator. Under service conditions, Flow-Accelerated Corrosion (FAC) produces local wall-thinning in the feeder pipes. The wall-thinning in these pipes affects the integrity of the piping system, as verified in previous research. This paper provides limit loads for wallthinned feeder pipes with $45^{\circ}$ and $60^{\circ}$ bend angles, and proposes an equation that predicts the limit loads for wallthinned feeder pipes with arbitrary bend angles. On the basis of finite element limit analyses, limit loads are obtained for wall-thinned feeder pipes under in-plane bending and internal pressure. There are two cases of in-plane bending: the in-plane closing direction and the in-plane opening direction. The material is considered the effect of the large deformation, so an elastic-perfectly-plastic material is assumed in the calculations.

• Journal of Convergence for Information Technology
• /
• v.12 no.3
• /
• pp.141-150
• /
• 2022

Fluid flow and thermal characteristics of laminar nanofluid(water/Al2O3) flow in a circular U-bend tube have been studied numerically. In this study, the effect of Reynolds number and the solid volume fraction and the impact of the U-bend on the flow field, the heat transfer and pressure drop was investigated. Comparisons with previously published experimental works on horizontal curved tubes show good agreements between the results. Heat transfer coefficient increases by increasing the solid volume fraction of nanoparticles as well as Reynolds number. Also, the presence of the secondary flow in the curve plays a key role in increasing the average heat transfer coefficient. However, the pressure drop curve increases significantly in the tubes with the increase in nanoparticles volume fraction.