• Journal of Aerospace System Engineering
• /
• v.11 no.1
• /
• pp.1-7
• /
• 2017

While a satellite is carried into orbit by a launch vehicle, it is exposed to the severe launch environment with random vibrations and shock. Accordingly, these vibration sources affect electronic equipment, particularly the printed circuit board (PCB) in the satellite. When the launch load impacts the PCB, it causes negative behavior. This causes perpendicular bending around the boundary of fixation points that finally leads to the failure of solder joints, lead wires, and PCB cracks. To overcome these issues, the electronic equipment design must meet reliability requirements. In this paper, Steinberg's method is used to derive allowable and maximum deflection to verify design from a life perspective concerning the control board of the Antenna Pointing Driver (APD) mounted on KOMPSAT-3.

• Journal of Aerospace System Engineering
• /
• v.14 no.spc
• /
• pp.13-21
• /
• 2020

RTCA DO-178C is a development guideline to ensure aircraft system airworthiness. However, there is an opinion that the application of DO-178C to the development of UAV of more than MTOW 150 kg is over regulated because the severity of the risk from UAV is lower than that of normal aircraft. To address issue, EASA and FAA have been working on the Re-Engineering and Streamlining the Standards for Avionics Certification(RESSAC) project since 2016 with the goal of establishing a new certification scheme that simplifies existing aircraft certification procedures and standards. This paper analyzes the current DO-178C certification process and presents advantages by comparing and analyzing the new RESSAC certification process, which simplifies processes and outputs in comparing with the DO-178C certification process, while it ensures flight safety of the vehicle.

• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.159-165
• /
• 2006

In this study, structural analysis is executed about cone structure of KSL V-1 2nd stage KMS(kick motor support structure) which is designed for support the load developed from 2nd stage kick motor. KMS is consisted of cone structure and truss structure which is designed for supporting load developed from 2nd stage payload. Applied loads to cone structure are tension load by inertia developed from kick motor and compression load developed from kick motor. Also, shear and bending load are developed according to flight condition. In this study, structural analysis of cone structure is executed under several load condition which may be applied to cone structure. Also, structural analysis with two finite element model is performed according to pressure vent scheme. In result of structural analysis, critical load condition is equivalent tension load with cut-out.

• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.16-26
• /
• 2006

GNSS is a satellite-based radio navigation aid. For using it in civil air navigation area, any GNSS service should meet the requirements of accuracy, integrity, continuity and availability in each flight phase established by ICAO. In this study, a remote integrity monitoring system(RIMS) for GNSS are proposed and explained to utilize it in the design of GNSS augmentation system such as GBAS and GRAS. The RIMS consists of signal-in-space receiving subsystem and signal processing subsystem. Each GPS receiver is connected to Host PC by the serial to ethernet converting device which is able to convert serial port connection to LAN port connection in order to exchange information via the internet. We can overcome the siting limitation of GPS receiver and antenna, and reduce signal loses in the cable between GPS antenna and receiver. This system is providing the development environment for GBAS CAT-I system.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.8-27
• /
• 2002

In this study, the load analysis of a composite canard aircraft is performed numerically. Excel visual basic program for PC is used to calculate aerodynamic coefficients, loads and moments etc.. The basic data required for the load analysis such as aircraft configuration and dimension, parts and its weight and coordinate etc. are obtained from Catia modeling, measurement or material density. Aircraft weight, center of gravity, inertia moment, structural design speeds, wing load distribution, forces and moments are evaluated by using these data. V-n diagram is also represented for selecting critical loads applied to the wing and fuselage. The V-n diagram is investigated to decide the flight envelope of canard aircraft for design speed VA, VC, VD and load factor +3.8G, -1.52G at maximum weight of 2,573 lbs and sea level. In the future, the results of the wing and fuselage load analysis is to represented by using selected critical loads.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.105-112
• /
• 2002

In this paper, a servo filter design for the gimbal engine actuator system of KSR-III(Korea Sounding Rocket-III) is considered. A reasonable filter structure is determined based on the actuator analytic models. The servo filter consists of a 2-nd order lowpass filter and a 1-st order compensator. The lowpass filter is required to protect the actuator from high frequency vibration, and the compensator to enhance the resulting stability. A Butterworth type servo filter is considered as the simplest one. The final servo filter type is determined by evaluating simultaneously both high frequency gain reduction performance and the corresponding KSR-III stability margin. Consequently it is revealed that a notch type servo filter located on the error between command signal and feedback signal in the control loop is very effective. Later, based on the proposed servo filter type, an onboard servo filter hardware of KSR-III will be designed and tested.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.6
• /
• pp.120-130
• /
• 2013

A study was conducted for the performance characteristics of methane taking recently the limelight in the world as a next-generation propellant, with the survey for state of the art in the development of methane/oxygen rocket engine being accompanied. Liquid methane as a rocket fuel has the favorable characteristics such as non-toxic, low cost, regenerative cooling capability, and potential for in-situ resource utilization (ISRU). The combination of liquid methane and liquid oxygen also provides the excellent performance including high specific impulse and low system mass. For these reasons, many researches have been actively carried out on the methane/oxygen engine, nevertheless, its technology readiness level is not that high enough just yet. Therefore, it is judged that it is the time to mitigate the technical gap with the space technology of advanced countries through a swift onset of the development of methane rocket engine.

• Journal of Aerospace System Engineering
• /
• v.8 no.4
• /
• pp.24-31
• /
• 2014

The modern version of aircrafts is allowed to guarantee the superior handing qualities within the entire flight envelope by imposing the adequate stability and flying qualities on a target aircraft through the various techniques of flight control law design. Generally, the flight control law of the aircraft in service applies the various techniques of the verified control algorithm, such as dynamic inversion and eigenstructure assignment. The supersonic trainer employs the RSS(Relaxed Static Stability) concept in order to improve the aerodynamic performance in longitudinal axis and the longitudinal control laws employ the dynamic inversion with proportional-plus-integral control method. And, lateral-directional control laws employ the blended roll system of both beta-betadot feedback and simple roll rate feedback with proportional control method in order to guarantee aircraft stability. In this paper, the lateral-directional flight control law is designed by applying dynamic inversion control technique as a different method from the current supersonic trainer control technique, where the roll rate command system is designed at the lateral axis for the rapid response characteristics, and the sideslip command system is adopted at the directional axis for stability augmentation. The dynamic inversion of a simple 1st order model is applied. And this designed flight control law is confirmed to satisfy the requirement presented from the military specification. This study is expected to contribute to design the flight control law of KF-X(Korean Fighter eXperimental) which will proceed into the full-scale development in the near future.

• Journal of Aerospace System Engineering
• /
• v.11 no.6
• /
• pp.84-91
• /
• 2017

The dynamic characteristics of a ducted fan in hovering condition were investigated. The section properties of the fan blade were calculated, and a simulation model was developed according to the rotor system components. Dynamic analyses were conducted relative to the rotational speed and the collective pitch. The proposed ducted fan system showed less aero-elastic instability within the designated operating ranges. To verify the analytical approach, a rotating test stand of the ducted fan was set up. A functional test of the assembly was carried out to determine the kinematics and interference between components. The non-rotating and rotating normal frequencies were measured by excitation of the collective pitch using hydraulic actuators. The results indicated a correlation between the test equipment and the simulation model.

• The Korean Journal of Air & Space Law and Policy
• /
• v.24 no.1
• /
• pp.3-35
• /
• 2009

A concept of Aircraft crime includes an Air range, unlawful seizure of aircraft and unlawful acts against the safety of civil aviation. There are international treaties and conventions which have mainly been enacted by ICAO. The following treaties and conventions are categorical and unconditional norms that any States are clearly condemned. Convention on Offences and Certain other Acts Committed on Board Aircraft, Convention for the Suppression of Unlawful Seizure of Aircraft, Convention for the suppression of unlawful acts against the safety of civil aviation, Protocol for the Suppression of Unlawful Acts of Violence at Airports Serving International Civil Aviation, Convention on the Marking of Plastic Explosives for the Purpose of Detection In this essay, I present the meaning of the aircraft crime mentioned on the treaties above and jurisdiction of the crime. Moreover, I explain how to demand reparation for damages onboard or on the surface when an aircraft crime is occurred. Lastly, I indicate legal bases of how to protect the victims of the aircraft crime by mentioning specific cases relating to the crime.