• Korean Journal of Environment and Ecology
• /
• v.20 no.1
• /
• pp.1-8
• /
• 2006

The objective of this study was to monitor the regenerated process of natural vegetation on the rear-slope of Jangheung multi-purpose dam using the recycling eco-revegetation technique. The monitoring plots were established in May 2004 and the plots were monitored in May 2004 and October 2005. Flora, plant community structures, naturally introduced plants, death rates were monitored. The change of flora after wood chip mulching decreased in family and species, but the influence of vine tree was extended. The urbanization index declined. Naturally introduced species and death ratios at the monitoring plot had a tendency to a higher increase in the deciduous broad-leaved forest.

• Journal of agriculture & life science
• /
• v.52 no.6
• /
• pp.81-88
• /
• 2018

This study analyzed the characteristics of 6 recyclable bulking agents which can replace sawdust and rice hulls that are commonly used in livestock manure composting. The content of all the hazardous chemicals found in the bulking agents used in this experiment was between 0.0 and 34.1 ppm, which was noticeably lesser than the maximum content levels of hazardous substances 5.0~900.0 ppm prescribed by the Rural Development Administration(RDA), which means that the bulking agents would be able to replace sawdusts and rice husks. The water content of the bulking agents ranged from a minimum of 12.4% to a maximum of 16.6% in the original state, which was much less than 60%, the optimal moisture content. These results indicate that they would be able to function fully as bulking agents. Their water absorption rate was in the range of minimum 31.9% ~ maximum 600.0%, which showed huge differences among the types of bulking agents. The most appropriate bulking agent in terms of water absorption rate was wood pellets. It was the highest in the wood briquette manufactured by A, which was followed by C and B in the order. The shear strength of the 5 types of bulking agents in the original state was 271.7 N on an average, the highest figure of all, except for the oak briquette whose shear strength could not be measured and the wood pellets in the absorption state. The shear strength in the dry and absorption states then followed, and were 78.0 N and 27.7 N on an average, respectively. The wood briquette of A recorded considerably lower shear strength than that of B and C. Overall, shear strength tended to increase according to lower water absorption rates. Since pine wood chips and oak cuts have relatively greater shear strength even in the absorbing state than the other materials, they will be able to endure some power in the case of stirring with pig droppings.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.56 no.6
• /
• pp.55-62
• /
• 2014

Torrefaction is considered as a promising pre-treatment for thermochemical utilization of biomass. Torrefaction temperature and time are the critical operation parameters. In this study, investigated were the effects of reaction temperature and time on product composition of torrefaction. scanning electron microscope (SEM) images and thermo gravimetric analyzer (TGA) results were also compared for the effects of the operating parameters. SEM images showed that the pores were observed at the temperature of $250^{\circ}C$ for 30 minutes. Rapid decreases in weight were observed the temperature between 200 and$400^{\circ}C$. Higher heating value of the torrefied biomass was over 5,000 kcal/kg at the temperature of $250^{\circ}C$ for 45 minutes. Energy density, which is defined as the ratio of the energy yield over the mass yield was 1.36 at the temperature of $250^{\circ}C$ for 45 minutes. The energy density was higher up to 1.6 at the temperature of $280^{\circ}C$, which indicates greater loss in mass. The major components of the gas produced in the torrefaction were $CO_2$ and CO, with traces of methane. The total amount of gas was 31.54 l/kg and the calorific value of the gas was $1,164.4Kcal/Nm^3$ at the temperature of $250^{\circ}C$ for 30 minute reaction time. Based on the results of this study, the temperature of effective torrefaction is about $250^{\circ}C$ for 30 to 45 minutes of reaction time. Considering the heating value, it is desirable to utilize the gas for efficient process of torrefaction.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.1
• /
• pp.42-51
• /
• 1997

The satellite channel with a line-of-sight signal component is modeled by a shadowed Rician fading channel. We adopt a direct-sequence / code division multiple access (DS / CDMA), which has the advantage to suppress the multipath effect and increase the user capacity. The performance which is evaluated by bit error probability is subjected to the influence of branch number, multi-user number, and spreading code-length. As the result of the analysis, performance advance is achieved with multi-user number decreasing, number of brnaches increasing, and spreading code-length increasing as chip duration is constant. To use both of diversity combining scheme and channel coding is more efficient for performance improvement than the case using diversity combining scheme only. The use of BCH coding and convolutional coding shows better consequence than Hamming coding. Totally, the performance degradation for heavy shadowing is much larger than that for light and average shadowing as heavy shadowing decreases LOS signal.

• New & Renewable Energy
• /
• v.8 no.4
• /
• pp.21-29
• /
• 2012

The extensible supply of New & Renewable energy resources desperately needs to counter the high dependence on imported energy, recent high oil prices and the Climate Change Conference, and the government has operated the 'Renewable Portfolio Standard' (RPS) as one of the renewable energy policy from 2012. By analyzing the operation case of combined heat and power plant using the woodchip biomass, we drew the price of wood chip fuel, plant capacity factor, electricity selling price, heat selling price and LCOE value. After analyzing the economic feasibility of 3MWe combined heat and power plant based on the operating performance, the minimum of economic feasibility has appeared to be secured according to the internal rate of return (IRR) is 6.34% and the net present value (NPV) is 3.6 billion won as of 20 years life time after installation, and after analyzing the cases of the economic feasibility of the price of wood chip, plant capacity factor, electricity and heat selling price are changed, the economic feasibility is valuable when the price of wood chip is over 64,000 won/ton, NPV is minus, and the capacity factor is above 46.9%, the electricity selling price is 116 won/kWh and the heat selling price is above 75,600 won/Gcal. When going over the new installation hereafter, we need the detailed review of the woodchip storage and woodchip feeding system rather than the steam-turbine and boiler which have been inspected many times, the reason why is it's hard to secure the suitable quality (constant size) of woodchip by the lack of understanding about it as a fuel because of the domestic poor condition and the calorific value of woodchip is seriously volatile compared with other fuels.

• Corrosion Science and Technology
• /
• v.22 no.3
• /
• pp.187-192
• /
• 2023

The use of biomass is increasing as a response to the convention on climate change. In Korea, a method applied to replace fossil fuels is using wood chips in a cogeneration plant. To remove air pollutants generated by burning wood chips, a selective denitrification facility (Selective catalytic reduction, SCR) is installed downstream. However, problems such as ash deposition and descaling of the equipment surface have been reported. The cause is thought to be unreacted ammonia slip caused by ammonia ions injected into the reducing agent and metal corrosion caused by an acidic environment. Element analysis confirmed that ash contained alkali metals and sulfur that could cause catalyst poisoning, leading to an increase in the size of ash particle and deposition. Measurement of the size of ash deposited inside the facility confirmed that the size of ash deposited on the catalyst was approximately three times larger than the size of generally formed ash. Therefore, it was concluded that a reduction in pore area of the catalyst by ash deposition on the surface of the catalyst could lead to a problem of increasing differential pressure in a denitrification facility.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.339-339
• /
• 2020

도시화로 인한 불투수면적의 증가와 기후 변화로 인한 강우패턴의 변화 자연적 물순환 체계에 악영향을 미치며. 이를 해결하기 위하여 국내에서는 도시 내 빗물관리 및 비점오염원 저감이 가능한 저영향개발(Low Impact Development, LID)를 적용하고 있다. 건기시 도로, 주차장등 차량통행 및 유동인구가 많은 지역에서는 입자상 물질들이 많이 발생되어 노면에 축적되어 있다가 강우시 강우유출수를 통해 시설로 유입된다. 이로 인해 시설 내 오염물질 및 퇴적물이 축적되어 여재 공극막힘현상 및 침투율저하의 문제가 발생되어 시설 내 효율이 감소된다. 따라서, 레인가든의 장기 모니터링을 통해 시설 내 유입되는 오염물질의 성상 분석 및 시설 내부의 퇴적물 분석을 통해 LID시설 운영의 효율성 평가를 수행하였다. 모니터링은 강우시 모니터링과 건기시 집수구역, 침강지, 시설 상부, 중부, 하부 등 총 5곳에서 채취하여 분석을 수행하였다. 모니터링은 평균 선행건기 일수는 5.46±4.7 days, 평균 강우량은 14.31±11.4 mm, 평균 강우강도는 5.33±6.7 mm/hr의 강우사상에서 모니터링을 수행하였다. 시설 내 평균 유입수농도는 TSS 98.0 ± 32.7 mg / L, COD 133.6 ± 6.3 mg / L, TN 5.77 ± 4.05 mg, TP 0.54 ± 0.03 mg / L으로 분석되었다. 유입부 내 퇴적물 종류는 Sandy Clay Loam으로 나타났으며, Cr 0.36mg / kg, Cu 5.17 mg / kg and Pb 6.04 mg / kg으로 중금속의 함유량이 높은것으로 분석되었다. 퇴적물은 침강지 및 시설 유입부에서의 입자크기는 49-113㎛ 약 60%의 퇴적물이 축적되어 제거되는 것으로 나타났다. 시설 내 침강지에서 50㎛ 이상의 입자들이 여과, 흡착 및 침전으로 인하여 40% 이상의 입자들이 제거되는 것으로 분석되었으며, 50㎛ 미만의 입자들은 시설 내 중간부, 유출부에서 제거되는 것으로 분석되었다. 침강지에서 유입수 대부분의 입자상물질들이 흡착 및 여과로 인한 제거가 이루어지기에 침강지 여재부는 넓은 표면적, 우수한 흡착능 및 여과율을 고려하여 선정하영 하며, 잦은 교체를 위하여 중량성이 낮은 우드칩 등이 적당한 것으로 사료된다.

• Journal of Wetlands Research
• /
• v.17 no.3
• /
• pp.228-236
• /
• 2015

Urbanization causes many environmental, hydrological and ecological problems such as distortion of the natural water circulation system, increase in nonpoint source pollutants in stormwater runoff, degradation of surface water quality, and damage to the ecosystem. Due to the increase in impervious surface by urbanization, developed countries apply low impact development (LID) techniques as important alternatives to reduce the impacts of urbanization. In Korea, LID techniques were employed since 2012 in order to manage nonpoint source pollutants. LID technology is a technique for removing pollutants using a variety of physical, chemical and biological mechanisms in plants, microorganisms and filter media with the reduced effluence of stormwater runoff by mimicking natural water circulation system. These LID facilities are used in a variety of filter media, but an assessment has not been carried out for the comprehensive comparison evaluation of adsorption and desorption characteristics for the pollutant removal capacity. Therefore, this study was conducted to analyze the adsorption and desorption characteristics of various filter media used in the LID facilities such as sand, gravel, bioceramic, wood chips and bottom ash etc. in reducing heavy metals(Pb, Cu). In this study, the adsorption affinity for Pb in all filter media was higher than Cu. Pseudo second order equation and Langmuir-3 isotherm are more applicable in the adsorption kinetic model and adsorption isotherm model, respectively. As a result of the desorption experiment, the filter media does not exceed KSLT which is the hazardous substance leaching limit, showing the capability of the filter media in LID. The bioceramic and woodchip as filter medias were evaluated and exhibited excellent adsorption capacity for Pb.

• Journal of Intelligence and Information Systems
• /
• v.20 no.2
• /
• pp.163-178
• /
• 2014

Following research proposes "Virtualization of Smart Cards (ViSCa)" which is a security system that aims to provide a multi-device platform for the deployment of services that require a strong security protocol, both for the access & authentication and execution of its applications and focuses on analyzing Virtualization of Smart Cards (ViSCa) platform-based mobile payment service by comparing with other similar cases. At the present day, the appearance of new ICT, the diffusion of new user devices (such as smartphones, tablet PC, and so on) and the growth of internet penetration rate are creating many world-shaking services yet in the most of these applications' private information has to be shared, which means that security breaches and illegal access to that information are real threats that have to be solved. Also mobile payment service is, one of the innovative services, has same issues which are real threats for users because mobile payment service sometimes requires user identification, an authentication procedure and confidential data sharing. Thus, an extra layer of security is needed in their communication and execution protocols. The Virtualization of Smart Cards (ViSCa), concept is a holistic approach and centralized management for a security system that pursues to provide a ubiquitous multi-device platform for the arrangement of mobile payment services that demand a powerful security protocol, both for the access & authentication and execution of its applications. In this sense, Virtualization of Smart Cards (ViSCa) offers full interoperability and full access from any user device without any loss of security. The concept prevents possible attacks by third parties, guaranteeing the confidentiality of personal data, bank accounts or private financial information. The Virtualization of Smart Cards (ViSCa) concept is split in two different phases: the execution of the user authentication protocol on the user device and the cloud architecture that executes the secure application. Thus, the secure service access is guaranteed at anytime, anywhere and through any device supporting previously required security mechanisms. The security level is improved by using virtualization technology in the cloud. This virtualization technology is used terminal virtualization to virtualize smart card hardware and thrive to manage virtualized smart cards as a whole, through mobile cloud technology in Virtualization of Smart Cards (ViSCa) platform-based mobile payment service. This entire process is referred to as Smart Card as a Service (SCaaS). Virtualization of Smart Cards (ViSCa) platform-based mobile payment service virtualizes smart card, which is used as payment mean, and loads it in to the mobile cloud. Authentication takes place through application and helps log on to mobile cloud and chooses one of virtualized smart card as a payment method. To decide the scope of the research, which is comparing Virtualization of Smart Cards (ViSCa) platform-based mobile payment service with other similar cases, we categorized the prior researches' mobile payment service groups into distinct feature and service type. Both groups store credit card's data in the mobile device and settle the payment process at the offline market. By the location where the electronic financial transaction information (data) is stored, the groups can be categorized into two main service types. First is "App Method" which loads the data in the server connected to the application. Second "Mobile Card Method" stores its data in the Integrated Circuit (IC) chip, which holds financial transaction data, which is inbuilt in the mobile device secure element (SE). Through prior researches on accept factors of mobile payment service and its market environment, we came up with six key factors of comparative analysis which are economic, generality, security, convenience(ease of use), applicability and efficiency. Within the chosen group, we compared and analyzed the selected cases and Virtualization of Smart Cards (ViSCa) platform-based mobile payment service.

• Korean Journal of Environment and Ecology
• /
• v.25 no.6
• /
• pp.893-902
• /
• 2011

The purpose of this study was to survey structures and growth conditions of Pinus densiflora village groves, and to establish management strategies for their desirable growth and conservation. Twelve village groves were selected in western Gangwon province for the study. The age of the study groves ranged from 50 to 200 years. Average dbh (diameter at breast height) and density of trees for each study grove were 27~52cm and 0.5~9.3 trees/$100m^2$, respectively. Soil environments were favorable to Pinus densiflora growth in the majority of the study groves, but 2 study groves with sandy soils showed considerably poor nutrient contents. Low tree vitality was found in some of the study groves due to poor conditions of root growth from soil fill and trampling. There were detachment of cambial tissue and damage of stem cavity at 6 study groves, which were caused by artificial injury, careless pruning, and frost damage. Light disease damage by Rhizosphaera kalkhoffii and phomopsis blight were found at 6 study groves. Light pest damage by Thecodiplosis japonensis was also found at 6 study groves, but the pest damage at 2 study groves was relatively considerable. Thus, major factors limiting normal growth of Pinus densiflora village groves were infertility, soil fill and trampling, stem damage, and disease and pest. Desirable management strategies were explored to solve growth-related problems and to conserve the study groves. The management strategies included fertilization of organic matter and lime, removal of soil fill, soil plowing and graveling, wood-trail installation or woodchip mulching, supply of wood fences and protective frames, surgical operation for damaged stems, vitality enhancement, and trunk injection to improve growth environments or control stem damage and disease/pest.