• Journal of Welding and Joining
• /
• v.5 no.1
• /
• pp.64-72
• /
• 1987

The Weldability of gavannealed steel using spot welder has been studied. The Results obtained are a follows; 1) Welds size and strength were increased depending on the welding time and welding current. But, the increasing rate has been decreased. 2) Deposited zinc has affected on the wear of welding tips and growth of welds but has not affected the weld's structures. 3) On shear testing of the specimen, button fracture has been observed and the value was approximately 540Kg (welds dia. approximately .phi.4mm)

• Journal of Welding and Joining
• /
• v.5 no.1
• /
• pp.16-22
• /
• 1987

오스테나이트계 스테인레스강 용접부의 .delta.-페라이트 생성인자에 관한 위의 실험결과로부터 아래의 결론을 얻을 수 있다. (1) 오스테나이트계 스테인레스강 용접부의 .delta.-페라이트는 에너지적으로 불안정한 상으로서, 오스테나이트로의 변태가 비가역적(irreversible)이다. (2) .delta.-페라이트의 생성 및 변태에는 합금원소의 확산이 반드시 수반되며, 최종 .delta.-페라 이트 함량은 정성적으로 다음과 같이 표시된다. 페라이트함량=primary페라이트-변태한 페라이트 (3) .delta.-페라이트 생성에 일차적으로 영향을 미치는 이자는 화학조성(Cr-당량/Ni-당량)이며, primary 변태양상 및 냉각속도에도 크게 의존한다. (4) 용착부 .delta-페라이트는 대개 Vermicular와 Lathy의 혼합조직으로 존재하며, 열영향을 받 을수록 에너지적으로 안정한 Globuar 형상으로 변해간다.

• Journal of Welding and Joining
• /
• v.6 no.4
• /
• pp.54-62
• /
• 1988

Major problems in welding Al-7020 include shrinkage, rpopositgy in welds and loss of strength in the heat affected zone. Thus it is important to examine the mechanical properties and reliability of welds. In this study, a series of experiments was carried out to determine the mechanical properties such as micro-hardness distribution, tensile strength, porosity and residual stress distribution of the Al-7020 weldment made by pulse-GMA welding. The resuts of the experiemnts are as folows. 1) The micro-hardness of weld metal and heat affected zone was lower than that of the base metal. 2) The tensile strength of the deposited metal was much lower than that of the base metal. 3) The porrosity in weld metal zone was negligible under the adopted conditsion of experiemnts. 4) The residual stress in the weld metal was lower than that of the heat affected zone, because the weld metal was softened. And the mciro-hardness distribution, the tensile strength and the residual stess distribution of the weldment in the as-welded condition were compared with those of the weldment after heat treatment.

• Journal of Welding and Joining
• /
• v.12 no.3
• /
• pp.56-62
• /
• 1994

The spot weldability of high strength steel sheet and two stories galvannealed high strength steel sheet has been studied. 1) Tensile shear strength decreased inversely as welding current increased over 12KA in the case of two stories galvannealed high strength steel sheet. 2) When heat flux input over 12KA, hardening region become narrow in case of two stories galvannealed high strength steel sheet. 3) The size of hardening region affect the strength of nuggets.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.72-72
• /
• 2010

최근 오일샌드, 극지유전, 심해저자원 등 극한지 자원개발이 활발해짐에 따라 수요가 증대되고 있는 극한지용 내마식 소재는 내마식성과 함께 저온 인성이 요구된다. 철계 합금에서 관찰되는 변형유기 마르텐사이트 상변태는 입자의 충돌에 의한 충격을 흡수하고 소재의 표면을 가공경화시켜 내마식성 향상 및 저온 인성에 기여할 수 있을 것으로 기대되고 있지만 합금조성의 정교한 제어가 필요하기 때문에 오버레이 용접에 적용하기 위해서는 모재와의 희석률을 제어하는 방안이 필요하다. 용접플럭스 설계기술은 용접시 금속이행모드, 용융지 유동거동 등과 같은 용접현상 제어를 통해 오버레이 용접재료의 용접성과 용접부 희석률을 최적화할 수 있는 기술이다. 본 연구에서는 내마식 고인성 오버레이 용접재료의 개발을 위해 Fe-12Cr-1.2C 합금조성을 갖는 메탈코어드 와이어에 대하여 아크안정제로 사용되는 Ca 함유 용접플럭스 첨가가 용착부 형상 및 희석률 변화에 미치는 영향을 조사하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.1
• /
• pp.115-124
• /
• 1989

Near-threshold fatigue crack-growth behavior at room temperature for a duplex stainless steel weldments was investigated to evaluate the effect of load ratio, microstructural change, and residual stresses. Near-threshold fatigue crack propagation behavior is found to show a marked sensitivity to .alpha./.gamma. phase ratio, and little residual stress effects. Threshold values in the heat affected zones are higher than those of base metals and threshold values for crack growth decrease with increasing the load ratio in the base metals and weldments. The fractrographic features in base metals, weldments and heat affectred zones were discussed in terms mechanism of crack growth.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.1
• /
• pp.17-22
• /
• 2011

As the quality of a weld joint is strongly influenced by process parameters the welding process, an intelligent algorithms that can predict the bead geometry and shape to accomplish the desired mechanical properties of the weldment should be developed. In this study, prepared by ${\Phi}1.6mm$ GMA welding of metal wire nose Advice jowelui 350A 600A grade level inverter welder and DAIHEN SCR's were carried out using welding. Welding conditions were 5.5m/min wire feed rate the welding current is rapidly transmit approximately 260A, welding voltage was about 30V. CTWD a 22mm, shielding gas was Ar 20L/min and the welding speed was a 240mm/min. Using data collected during welding equipment welding current and welding voltage waveform was analyzed by measuring the volume of the transition mode. Addition of $CaCO_3$ as a loss of the spread of the weld bead dilution rate decreased, suggesting that, GMA in the overlay welding bead shape control, dilution control and may be used as a welding flux is considered. Stabilizing effect of the arc by the Ca-containing $CaF_2$, $CaCO_3$, $CaMg(CO_3)_2$, respectively, welding flux 0.1wt.% added GMA welding and weld overlay were evaluated with dilution, $CaF_2$, and $CaMg(CO_3)_2$ added to the dilution of Seemed to increase.