• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.457-463
• /
• 2016

The newly developed super ductile duplex stainless steel (SDSS) has good strength and ductility, and it can be used to reduce weight and improve the fabrication efficiency of a carbody of a rolling stock. In this study, spot weldability tests were conducted to take advantage of SDDSS in a carbody for an intermodal tram. Specimens of various thickness (0.4 to 5.0 mm) were prepared to find the proper welding conditions, and tensile load tests were conducted to evaluate the tensile-shear strength of spot welded joints. Then, nugget diameters were measured to verify the quality. The tensile-shear strength was found to be proportional to the heat parameter. It was verified that the tensile-shear strengths and nugget sizes of the joints satisfy the standard requirements. The overall weldability tests confirmed that SDDSS can be used effectively for the carbody of an intermodal tram.

• Journal of the Korean Society for Railway
• /
• v.9 no.4 s.35
• /
• pp.371-378
• /
• 2006

This study investigates the effects of the material properties and the fatigue behaviors in the SM490A material butt weld specimens due to the heat-treatment and the grinding. In the fatigue behavior, the heat-treatment affects the fatigue life. The S-N curves of both matrix specimen and butt weld specimen are reversed at some cycle by the existence or nonexistence of heat-treatment. The grinding on the bead makes the fatigue limit decrease in the all specimens. But the reinforcement removed, the fatigue limit increases at the high cycle. Also, this study investigates the fatigue life estimation by examining butt weld bead profiles. The butt weld beads, which are welded by semi-robot method, have non-uniform bead profiles described by $\theta,\;\rho$ and h. The stress concentration factors $K_t$, are changed by each different $\theta,\;\rho$ and h from 1.395 to 2.863. Hence, the sensitivity of $K_t$ is changed by each $\theta,\;\rho$ and h. As $\theta$ becomes lower and $\rho$ and h become higher, $K_t$ increases. The fatigue life can he estimated very closely for the AAY specimens without residual stress using only butt weld bead profiles. But, fur the AAN specimens with residual stress, the fatigue life must be estimated by considering both the weld bead profiles and the residual stress data.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.2
• /
• pp.95-103
• /
• 2021

Sn-58Bi-xRu composite solders were prepared by adding Ru nanoparticles to Sn-58Bi, a typical low-temperature solder, and the interfacial reaction and solder joint reliability were analyzed by reacting with Cu/OSP and ENIG surface treated PCB boards. The Cu₆Sn₅ IMC formed by the reaction with Cu/OSP had little change in thickness depending on the Ru content, and ductile fracture occurred inside the solder during the high-speed shear test without any significant change even after 100 hr aging. In reaction with ENIG, the Ni₃Sn₄ IMC thickness tended to decrease as the Ru content increased, and ENIG-specific brittle fracture was found in some specimens. Since Ru element is not found near the interface, it is judged not to be significantly involved in the interfacial reaction, and it is analyzed that it mainly exists together with the Bi phase.

• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.1
• /
• pp.82-89
• /
• 2002

The inherent strain method is known to be very effective in predicting the plate deformation by line heating. Traditionally the inherent strain regions have been determined from the temperature distribution and the phase transformation regions(Ac3) of welding experiments. Since the phenomena of line heating are similar to those of welding, the experimental results under the same welding conditions have been applied directly to line heating analysis. The results cannot, however, reflect the effect of heating pattern and plate thickness. Besides, water-cooling in the actual heating process can alter the steel's phase to martensite and shear plastic deformation occurs during the transformation. In this study, the experimental measurement of temperature distribution was substituted with a transient heat transfer analysis using FEM so that we could obtain the temperature distribution according to heat flux models of the heating pass. In order to consider plastic strains occurring additionally under phase transformation, inherent strain regions were assumed to be limited to the eutectoid temperature(Ac1). Using the regions, plate deformations could be predicted to validate our method and the results were in good agreement with the experimental ones

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.42-50
• /
• 2016

Overlay welding affects the chemical components and weld hardness by dilution of the lamination layer thickness, which determines the surface properties. This study experimentally investigates different numbers of layers for overlay welding monel materials, which are anti-corrosion materials. The Fe content, weldability of the base metal and monel materials, hardness, and surface flatness were examined. Each evaluation was carried out after overlay welding with three layers on the base material and pipe base material of the plate. The Fe content was evaluated by analyzing the constituents of each layer. The Fe content was satisfactory in the three layers. The weldability of the laminate specimens was evaluated by a bending test. The hardness and bead flatness of the laminate specimens were evaluated by micro Vickers and 3D measurements. The hardness was highest in the heat-affected zone with one layer, and it decreased with increasing lamination. In the case of bead flatness, there is a sharp difference in the deviation with increasing numbers of laminations, which should be considered carefully.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.139-139
• /
• 2017

최근 환경오염 문제로 인한 연비 규제 강화 속도가 빨라지고 있으며 이에 따른 연비 향상 기술이 크게 대두 되고 있다. 연비 향상 기술 중 경량화 방안소재로 알루미늄(Al), 마그네슘(Mg) 등의 비철금속을 주로 사용하고 있으며, 이중 알루미늄은 다른 경량화 금속소재보다 우수한 경쟁력을 가지고 있다. 하지만 경제적인 측면에서 철 대비 비용적인 어려움을 가지고 있고 용접성이 떨어지기 때문에, 자동차 부품의 일부만 알루미늄 소재를 선택하여 사용하고 있는 실정이며 알루미늄의 높은 이온화 경향으로 인해 기존 자동차 철강 소재와 접촉 시 쉽게 부식되는 단점을 가지고 있다. 이러한 문제점을 해결하기 위해서는 알루미늄의 금속원소를 첨가하는 연구가 지속적으로 개발 되고 있다. 알루미늄 합금에서 마그네슘의 첨가는 좋은 용접성과 내식성, 강도를 향상시킨다. 하지만 3%이상의 마그네슘 첨가는 입계에 ${\beta}(Al_xMg_y)$석출상이 석출되게 되며, 입계에 연속적으로 형성된 ${\beta}(Al_xMg_y)$석출상은 응력 부식 균열 (Stress corrsion cracking)과 입계 부식(Intergranular corrosion)을 야기하는 결과를 가져온다고 알려져 있다. 이 문제를 해결하기 위해 Al 5000계열 합금의 Zn의 첨가를 통해 ${\tau}(Al_xMg_yZn_z)$을 입계에 석출시켜서 입계에 ${\beta}(Al_xMg_y)$상의 석출을 방지함으로써 내식성을 향상시키거나 Al 5000계열 합금의 열처리를 통해 ${\beta}(Al_xMg_y)$석출상을 고용시킴으로써 응력부식균열의 발생을 억제하는 연구도 있다. 하지만 열처리 후 Polarization test를 이용한 내식성 연구는 잘 안 알려져 있다. 따라서 이번 연구에서는 Al5000계열의 주조한 합금을 DSC분석을 통하여 ${\beta}(Al_xMg_y)$석출상의 고용 온도가 약 $470^{\circ}C$라는 것을 확인한 후, 실온에서 $100^{\circ}C/hr$으로 가열하고 조건에 따라 $450^{\circ}C$에서 3시간, 6시간, 12시간, 24시간, 30시간 항온 유지시킨 후 공냉을 진행하였다. 열처리를 마친 시편은 에폭시를 이용하여 마운팅 하였으며, 시편표면을 2000#까지 연마 후 증류수로 세척한 다음 질소를 이용하여 건조 후 분극 시험을 진행하였다. 3.5wt% NaCl 용액에서 분극 곡선을 통해 부식거동을 확인한 결과 24시간까지 시간이 증가 할수록 내식성이 우수해지는 것을 확인하였으며, 추가적으로 조직사진, SEM & EDS 분석과 XRD, TEM 분석을 통해 내식성은 입계에 존재하는 Mg의 조성이 감소하게 되면 내식성이 향상되는 것을 관찰하였다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.1
• /
• pp.46-53
• /
• 2001

The purpose of this paper is to develop a new feature selection method for AE signal classification. The neural network of back propagation algorithm is used. The proposed feature selection method uses the difference between feature coordinates in feature space. This method is compared with the existing methods such as Fisher's criterion, class mean scatter criterion and eigenvector analysis in terms of the recognition rate and the convergence speed, using the signals from the defects in welding zone of austenitic stainless steel and in the metal contact of the rotary compressor. The proposed feature selection methods such as 2-D and 3-D criteria showed better results in the recognition rate than the existing ones.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.24-24
• /
• 2010

마찰교반접합법은 특정한 회전수로 회전하는 용접 툴을 이용하여 접합하고자 하는 피접합재의 맞댄면에 삽입시킨 후 툴을 이동시키거나 혹은 시편을 견고하게 고정시킨 장치(backing plate)가 움직여 고상 상태에서 접합이 이루어진다. 알루미늄, 마그네슘 등 비교적 융점이 낮은 저융점 재료의 재료에 처음 적용이 되어 많은 연구가 활발히 진행되었고 타 용접방법에 비해 우수한 접합특성을 나타내었다. 최근 이러한 마찰교반접합은 이러한 저융점 재료를 넘어서 스틸, 타이타늄, 니켈 등과 같은 고융점 재료 등에 대한 적용이 늘어나고 있다. 마찰교반접합을 이용하여 이러한 고융점 재료의 접합 경우 내마모성 및 내열성 등의 내구성이 갖추어진 툴과 이러한 툴을 냉각시킬 수 있는 냉각 장치 등이 필요로 하나 경제적 측면이나 접합부의 우수한 특성 등을 고려 할 때 그 적용 및 발전 가능성이 매우 높다고 볼 수 있다. 2상 스테인레스 강은 금속 조직적으로 페라이트와 오스테나이트 상이 거의 1:1의 동등한 비율로 매우 미세하게 결합된 구조를 가지고 있다. 또한 이상 스테인레스 강은 각상의 개개의 특성에 기인하여 염소 분위기에서 응력부식 저항성이 우수하고, 공식과 틈부식에 대한 저항성이 매우 뛰어나다. 그리고 이상 스테인레스 강은 비교적 고가인 Ni이 일반 오스테나이트 스테인리스 강의 약 1/2의 수준으로 적게 포함이 되어 경제적인 이점을 지니고 있으며 또한 용접성이 좋아 산업계의 수요는 현재 점차 증가하고 있는 상황이다. 하지만 이러한 이상 스테인리스 강은 용접 후 페라이트 상의 조대화, 그리고 페라이트 상의 분율이 오스테나이트 상의 분율보다 높아지게 되어 용접부에서의 저온 인성 감소 및 내식성 저하 등의 문제가 발생하게 된다. 그리하여 용접 시 이러한 문제점을 해결하기 위해서는 입열량의 조절이 가장 필요로 하는 것으로 알려져 있다. 본 연구에서는 마찰교반용접을 이용하여 두께 3mm의 대표적인 이상 스테인리스 강인 SAF2205 스테인리스 강에 대해 맞대기 마찰교반접합을 실시하였다. 툴 회전속도를 변수로 하여 접합을 실시하였으며 접합 시 툴은 $Si_3N_4$ 툴을 사용하였다. 접합 후 외관상태 점검, 미세조직 관찰, 경도 및 인장강도 측정 등의 실험을 실시하였고, 이러한 결과를 이용하여 미세조직과 기계적 특성과의 관련성을 조사하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.124-129
• /
• 2017

In this study, we report characteristics of friction stir welding (FSW) technique applied to Al-6005-T6 extruded sheets, which is a common material for railway car bodies. With the welding speed fixed at 300 mm/min, the revolution per minute (RPM) of the rotating tool was varied from 600 to 1800 RPM, with the aim at evaluating the resultant microstructure and mechanical behaviors. Comparison is also made with the conventional Metal Inert Gas (MIG) welding technique. Unlike MIG, no micro-voids were observed for FSW specimens. Hardness measurement revealed that the increased heat input by increasing RPM results in widened heat affected zone (HAZ) and decreased hardness for HAZ due to grain coarsening. Hardness results for the nugget do no show difference. During tensile tests, specimens fractured at HAZ, and increasing rpm led to decrease of the yield stress and tensile stress for the selected RPM range, which is considered to be due to the grain coarsening for HAZ.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.3
• /
• pp.307-312
• /
• 2012

This study aims to investigate the effect of the post weld treatments on the fatigue life of T-type welded structure made by a SM50A steel material, generally used for excavators, because changes in the geometry, material and surface properties of welded regions affect the fatigue life of welded structures. T-type test specimens were prepared by the CO2 welding of rolled steel plates (SM50A steel) with a thickness of 10 mm at a welding speed of 30 cm/min and these Ttype welded specimens were further treated by UIT (Ultrasonic Impact Treatment) and/or toegrinding post welding treatment methods. In order to investigate improvements on the fatigue life of the samples. 3-point bending fatigue tests were conducted with a stress ratio of R=0.1 under a cyclic loading environment at a frequency of 5 Hz, via a hydraulic fatigue testing machine (${\pm}100\;kN$, MTS 809). The tests were performed at room temperature. The fatigue life of UIT specimens was approximately 25 times longer than that of as-welded specimens at a stress amplitude of 281 MPa, while toe-grinding specimens exhibited 4.15 times longer fatigue life. The current results could provide important guidelines to determine the proper post weld treatment methodologies of T-type welded parts for excavators with a satisfactory fatigue life although under severe operating conditions.