• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.3
• /
• pp.45-50
• /
• 1999

Copper has been widely used for the electronic parts, and especially spot welded one for the leads of condenser or resistor. However, copper is generally hard to be spot welded because of its low electrical resistivity. For this experiment, Sn-37%Pb solder which has relatively higher resistivity was coated on the Cu-sheet to improve the spot weldability of copper. As the experimental variables welding pressure was varied from 100 to 200kgf, welding time from 20 to 50ms, and welding current from 100 to 2500A. Experimental results showed that the solder coated Cu-sheet can be spot welded under the conditions of 400~2200A welding current, 100~200kgf pressure and 20-50ms welding time. The tensile shear strength of the spot welded joint increased with welding current up to the critical current, and after the critical value decreased with current.

• Journal of Welding and Joining
• /
• v.13 no.2
• /
• pp.12-24
• /
• 1995

Recently, more researches have been actively performed for the assessment of material degradation and residual-life of elevated temperature plant components, as some of domestic fossil power plants become older than 30 years. In this paper, results of on_site residual life assessment are reported for main steam pipes of Youngwol power station #2 which have operated since 1965. For critical weld locations such as butt welds branch welds, Y_sections and a T-section, replication technique and hardness measurement technique were employed for life_assessment. When cracks were detected by conventional NDT tests, crack growth life was calculated using a computer code. On the other hand, for matrix of pipes, residual life was quantitatively estimated by an analytic method and material degradation was estimated qualitatively using diameter measurement data and grain-boundary etching method. Also, direction in further improvement of on-site life assessment techniques are proposed.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.670-677
• /
• 2003

Although Gas Tungsten Arc Welding (GTAW or TIG welding) is considered as high quality and precision welding process, it also has demerit of low melting rate. Narrow-gap TIG welding which has narrow joint width reduces the groove volume remarkably, so it could be shorten the welding time and decrease the overall shrinkage in heavy wall pipe welding. Generally Narrow-gap TIG welding is used as orbital welding process, it is important to select the optimum conditions for the automatic control welding This paper looks at the application and metallurgical properties on Narrow-gap TIG welding joint of heavy wall large austenitic stainless steel pipe to determine the deposition efficiency, the resultant shrinkage and fracture toughness. The fracture toughness depends slightly on the welding heat input.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.3
• /
• pp.289-299
• /
• 2006

Orthotropic steel decks are manufactured by welding thin plates therefore it is inevitable that there are abundant works of welding process. On connection of transverse rib web, crossing point of longitudinal rib, transverse rib and deck plate and cut-out parts of transverse rib are the significant position of stress concentration phenomenon because of out of plane and oil-caning deformation caused by longitudinal rib distortion with shear force and distortion. In order to reduce the stress concentration phenomenon and improving fatigue performance at the crosing point and cut-out, structural analysis was performed considering the existence of scalop at conection and diaphragm which have same plane with transverse rib placed inside of longitudinal rib. Result o f the analysis show that there are the largest efect of stres concentration reduction when diaphragms are installed without scallop at connection, therefore these detail can improve the fatigue performance of orthotropic steel decks.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.151-159
• /
• 2017

The aspect of modern warfare is gradually changing to a network of warfare, and its central information electronic warfare is evolving every day. Recently, domestic equipment of electronic warfare, which have succeeded in domestic localization, are strongly influenced by the nature of the environment. Therefore, the structural reliability of the antenna switching module that connects the mast and antenna of the ES equipment is the most important. This study proposed a structure that has an improved structure of antenna switching module by currently analyzing the structure of the antenna switching module and the environmental influence. By modifying the structure of the antenna switching module welding method and part of the reinforcement block, the structure was improved and the validity of the improved antenna switching module was simulated using a load test. The simulation showed that the safety factors of antenna switching module welding point and reinforced block part was enhanced 5.3 and 1.5 times compared to the existing values. These values were verified by load (181kg) test results, which was each 3.7Mpa and 64.4Mpa. The load test results were similar to the simulation results and load supporting capacity of the proposed antenna switching module was enhanced.

• Journal of Korean Society of Steel Construction
• /
• v.25 no.5
• /
• pp.451-461
• /
• 2013

In steel bridges, there are several details that constrain the deformation such as buckling by external forces. Most of these details which are composed of the intersection members have scallops in order to exclude the weld defects inherently and to get the ease of fabrication and also to decrease the stress concentration. In this study, stress relief hole (SRH) near stress concentration zone with detail category D or under is proposed as a method to improve the resistance on the fatigue crack initiation to detail category C. And the effects of the appropriate size and location of SRH were examined and the applicability to improve the fatigue resistance of the floorbeam web and the rib wall at rib/floorbeam intersection in the orthotropic steel deck bridge was evaluated.

• Clean Technology
• /
• v.20 no.2
• /
• pp.171-178
• /
• 2014

In this study we have examined the health risk factors and analyzing data of laborers working at the welding operation at large-sized casting process. In order to improve the working environment of workplace, an effective ventilation method was proposed after performing CFD (computational fluid dynamics) modeling and measurement of pollutants. As a result of examining the health risk factors of workers, oxidized steel dust is the main pollution source in the company A, welding fume in the companies B and C, and welding fume and oxidized steel dust in the company D. The fume concentration in the workers' breathing zone was $0.05{\sim}4.37mg/m^3$, and the fume concentration in the indoor air at the welding process was $0.13{\sim}7.54mg/m^3$. From a result of CFD, a local exhaust with an exhaust duct adjacent to welding point was found to be most effective in case of the exhaust process. In case of air supply, we found that a desired location of air supply fan would be at the end of the opening. If a standardizing the ventilation system for tunnel-type semi-enclosed space at a large-sized casting process is introduced in welding work places in the future, it would be more effective to protect the health of welding workers working at the casting industry and shipbuilding industry and improve the work environment.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.7 no.4
• /
• pp.1-11
• /
• 2011

This paper presents the effects of preventive maintenance schemes on the residual stress distributions in dissimilar metal welds. Dissimilar metal weld is known susceptible to PWSCC and thus, effective maintenance schemes to prevent PWSCC are needed. Three preventive maintenances schemes, i.e. weld overlay, MSIP and inlay weld which are widely used in nuclear power plants, are selected and their effects on welding residual stresses are investigated via finite element analyses. As results, weld overlay and MSIP were proved effective method to mitigate residual stresses and inlay weld, on the other hand, produces strong tensile residual stresses in the inner surface. Although Alloy 690 known to be resistant to PWSCC are used in inlay weld, continuous careful observation are needed since tensile welding residual stresses are key parameter for PWSCC.

• Journal of Welding and Joining
• /
• v.9 no.4
• /
• pp.40-49
• /
• 1991

Both impact and fracture toughnesses were investigated with root gaps in FCAW weld metals at room temperature and 0.deg.C. The maximum impact value was obtained at the root gap of 16mm for 1G position weld metal, and the impact value of 3G position weld metals also showed the maximum impact value at the root gap of 12mm. However, the fracture toughnes(CTOD)values tend to decrease with increasing root gaps at both temperatures in 1G weld metal. Bending test also showed satisfactory results with all of root gaps investigated. Based on this result, it becomes possible to apply wide root gaps in real projects in both aspects of toughness and bending resistance.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.28-28
• /
• 2009

최근 전세계적으로 유가 상승 및 배기가스 배출 저감과 관련된 각종 환경규제에 대응하기 위하여 선진 자동차회사들은 $CO_2$ 배출 저감 기술과 기존 내연기관 차량의 연비향상을 위해 엔진성능 개선, 구동시스템의 최적화, 차량 경량화, 공기저항 감소 등에 초점을 맞춰 차량의 연비향상과 배기가스 규제에 대응하고 있다. 특히, 자동차 중량의 30%를 차지하는 차체의 경량화는 엔진효율을 높여 자동차의 성능향상을 극대화시키고, 그로 인해 연비향상을 도모할 수 있으므로 환경오염 방지와 연료절감에 가장 적합하고 효과적인 방법이다. 이에 기존의 강재에 비해 비중이 낮으면서 유사한 강도와 내식성이 뛰어난 알루미늄 합금의 차체 적용에 대한 연구가 진행되고 있다. 본 연구에서는 자동차 Door에 알루미늄 합금(Al 5052)의 적용 가능성을 판단하기 위해 반응표면분석법(Response surface methodology)을 이용하여 저입열 Pulse MIG 용접 공정변수를 최적화하였다. 첫째, 저입열 Pulse MIG 용접에서 용접 공정 변수(용접전압, 용접속도, Gap)의 변화가 비드 형상에 미치는 영향에 대해 평가하였다. 요인분석법을 이용하여 용접 공정 변수와 비드 형상 변수와의 주효과와 교호작용효과를 분석하였고, 이를 통해 비드 형상 변수에 영향을 크게 미치는 용접 공정변수를 선별하여 다중회귀분석을 통해 용접 공정 변수 변화에 따른 비드형상 예측 회귀모델을 제안하였다. 둘째, 자동차 Door 생산 현장에서 박판 알루미늄 합금 겹치기 용접 이음부의 0~1 mm 갭 발생에 대해 강건한 용접조건을 제시하기 위해 반응표면법(Response surface methodology)을 이용하여 저입열 Pulse MIG 용접 공정 변수를 최적화하였고, 그 적용 가능성을 확인하였다.