• Journal of the Korean Magnetics Society
• /
• v.5 no.3
• /
• pp.222-232
• /
• 1995

자기저항이란 외부 자기장에 의해 재료의 전기저항이 변화되는 현상을 일컫는다. Au와 같은 비자성도체 및 반도체 재료의 경우 외부에서 자기장이 가해지면 전도 전자가 Lorentz 힘을 받아 궤적이 변하므로 저항이 변화한다. 이러한 저항 변화 를 정상 자기저항(Ordinary Magnetoresistance, OMR)이라 하며 일반적으로 상당히 작은 저항의 변화를 나타낸다. 강자성도체 재료에서는 정상 자기저항 효과 외에도 부가적인 효과가 생긴다. 이는 스핀-궤도 결합에 기인한 효과로써 자기 저항은 강자성체의 자화용이축, 외부자계와 잔류간의 각도에 의존하며 이방성 자기저항(Anisotropic Magnetoresistance, AMR)이라 한다. AMR 비(%)는 일반적 으로 다음과 같이 정의된다. 즉 ${\Delta}{\rho}_{AMR}/{\rho}_{ave}=(\rho_{\|}-\rho_{T})/{\rho}_{ave}$로 여기서 $\rho_{\|}$는 자기장의 방향이 전류의 방향과 같을 때의 비저항 이고 $\rho_{T}$는 서로 수직일 때이며 ${\rho}_{ave}=(\rho_{\|}-\rho_{T})/3$이다. 기존의 MR 센서나 자기재생헤드(magnetic read head)에 사용되는 퍼머로이계 합금의 AMR 비는 상온에서 약 2% 정도의 저항변화를 보인다.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.3
• /
• pp.167-173
• /
• 2011

The Effects of external resistance on electrical properties such as current density, power density and coulombic efficiency were investigated in two-chamber type MFCs using a ferricyanide as reducing agent. A stable electricity was produced when a constant time elapsed after innoculation of mixed cultures into the anode compartment; voltages from 0.13 to 0.16 V was measured at $50{\Omega}$ of external resistance. When the external resistance was increased, the current density decreased and the power density rapidly increased and then slowly decreased. Big variation of electrical properties was observed in high-current density region due to the concentration loss related with substrate consumption in repeated experiments changing the external resistance. The maximum power density ($175.8mW/m^2$) and coulombic efficiency (46.1%) were obtained at $100{\Omega}$ of the external resistance which is nearest with the internal resistance ($134{\Omega}$) of MFC system.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.786-788
• /
• 2003

Bi-2223테이프의 동저항 및 동저항손실에 대해 조사하였으며, 그 주요 결과는 외부교류자장이 어느 정도 큰 경우에 한해서는 테이프의 동저항은 전류에는 의존하지 않고, 자장 및 주파수에는 비례한다. 또한 동저항손실은 전류가 증가함에 따라서 급격히 증가하며, 외부교류자장에 비례하고, 주파수에는 거의 의존하지 않는다.

• Composites Research
• /
• v.12 no.2
• /
• pp.1-9
• /
• 1999

The piezoelectric material connected to external electric networks possesses frequency dependent stiffness and loss factor which are also affected by the shunting circuit. The external electric networks are generally specialized for two shunting circuits: one is the case of a resistor alone and the other is the combination of a resistor and an inductor. For resistive shunting, the material properties exhibit frequency dependency similar to viscoelastic materials, but are much stiffer and more independent of temperature. Shunting with a resistor and inductor introduces an electrical resonance, which can change the characteristics of structural resonance optimally in a manner analogous to a PMD (proof mass damper). Passive damping enhancement of composite beam using piezoelectric material connected to external electrical networks is achieved and presented in this paper.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.895-898
• /
• 2003

본 논문에서는 휴대폰에 사용하는 리튬-이론 배터리(Li-Ion battery)를 충전하기 위한 충전 IC 의 설계에 대해서 기술한다. 정전류(Constant Current)/ 정전압 (Constant Voltage) 방식을 이용하여 리튬-이론 배터리를 충전을 하였다. 이 충전 과정을 제어하기 위해서 일반적으로 사용되는 ADC, DAC 와 MICOM 을 사용하지 않고, hardwired control logic 을 이용하여 적은 면적을 가지고도 기존의 충전 과정을 수행하도록 하였다. 충전 IC 외부에 사용되는 저항들을 내부에 집적하여 사용하는 부품의 수를 현저히 줄였다. 충전기와 리튬-이온 배터리를 연결하는 선(wire)로 저항에 의한 전압강하(voltage drop)를 외부에서 보상할 수 있도록하여 리튬-이온 배터리가 가장 안정적인 전압인 4.2 V로 충전 될 수 있도록 하였다. 외부 온도 검사 블록에서 저항을 이용한 전압 분배를 사용하지 않고, 정전류원을 이용하여 외부 온도 변화를 측정할 수 있도록 하였다. 리튬-이온 배터가 전정류와 정전압으로 4.2 V로 충전 되었으며, 충전 IC 의 소비 전력은 37 mW(analog part)이다. 충전 IC는 0.6 ㎛ standard CMOS 공정을 이용하여 설계하였다.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.11
• /
• pp.107-117
• /
• 2020

Open-ended steel pipe piles have outside frictional force and inside frictional resistance in which blocked soil acts on the inside of the steel pipe during installation. It is expected that the ultimate load will change depending on the inside and outside resistance. And, if the ground on which the piles were constructed is clay soil, it is predicted that it will have effect on the negative skin friction caused by the ground settlement. Therefore, in this study, the behavior according to the inside and outside resistance characteristics of steel pipe piles was analyzed numerically, and the frictional force distribution, axial load and settlements before and after the occurrence of ground settlement were calculated. As a result of the analysis, the inside frictional resistance had less influence than the outside frictional resistance. However, inside frictional resistance is considered to be one of the important factors considering the effect on the overall pile behavior, and both resistance factors need to be considered in the design process.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.931-933
• /
• 2000

Bi-2223 테이프의 실제 전력기기 응용측면을 고려할 때 테이프는 외부자계하에 놓이게 된다. 따라서 본 연구에서는 외부자계가 Bi-2223 테이프의 통전손실에 미치는 영향에 대해서 조사하였다. 비교적 작은 자계가 인가된 경우는 전압리드의 배역이 통전손실측정에 영향을 미쳤으나 비교적 큰 자계가 인가된 경우는 전압리드의 배열에 무관하다는 사실과, 전계와 통전손실은 외부사계가 증가함에 따라 각각 증가하였으며 비교적 큰 자계가 인가된 경우에 통선손실은 동저항 손실이 지배적이었으며. 외부자계가 작은 영역에서 통전손실은 동저항 이외의 또 다른 메카니즘에 의한 것으로 사려된다.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.450-453
• /
• 2009

본 논문에서는 지진하중을 고려하여 충분한 연성거동이 가능하도록 배근한 철근콘크리트 횡하중 저항 골조(내진상세)와 고정하중과 적재하중만을 고려하여 설계한 중력하중 저항 골조(일반상세)를 대상으로 외부기둥과 내부기둥에 연결된 보의 연쇄붕괴 거동을 평가하기 위한 실험을 수행하였다. 일방향 가력실험 결과에 따르면 내진상세의 경우 대변형 상태에서 보의 하단철근의 파단이후 상단 압축철근이 인장력을 부담하면서 전체 보 부재는 축인장력이 작용을 하면서 힘-변위 곡선은 상승하는 현수작용이 발현되었다. 그러나 일반상세의 경우 충분한 현수작용이 발현되기 전에 보의 주근이 정착된 외부기둥 접합부의 파괴로 인하여 저항내력이 감소하였다.

• Journal of Global Scholars of Marketing Science
• /
• v.15 no.3
• /
• pp.211-231
• /
• 2005

It is important for marketers to understand both individual resistance and group resistance in order to successfully bring innovations into global markets. We suggest that consumers resist innovations as individuals and as members of a group and that they do this in different ways at different stages of decision-making. The individual resistance begins with forms of initial resistance, develops into emergent resistance and mature or belated resistance at the individual level. In addition, personal moral standards can influence decision making in relation to the adoption of innovations. Individual resistance is sometimes accompanied by or evolves into group resistance. We introduce a framework for thinking about consumer resistance to innovations that sees it as a consequence of social identity, which has functions for the individual, the group to which one belongs, and other individuals and groups. Consumers with membership in a certain group try to increase their self-esteem through the process of social comparison. The more consumers strongly identify with and bond with a certain group, the more in-group solidarity and out-group hostility will occur. Out-group hostility gives group members strong resistance toward products and services related to the out-group. Individual resistance and group resistance are threats to marketers and dampen performance. By considering the existence of resistance to innovations and seeking strategies to overcome it, marketers can transform these threat into new opportunities. A better understanding of consumer resistance can complement research on the adoption of innovations and help in the development of a universal model of consumer behavior.

• Journal of the Korean Magnetics Society
• /
• v.8 no.4
• /
• pp.231-240
• /
• 1998

We investigated that the fabrication and reproducing signal characteristics of tri-layered magnetoresistance (MR) element for the high density magnetic thin film heads and sensors. Magnetoresistance curve of tri-layered MR element predicted by computer modeling was saturated above external field of -15 Oe~+22 Oe, and it was shifted to linearized region as large as 4 Oe. In the case of fabricated real device, magnetoresistance curve was saturated above external field of $\pm$15 Oe, and it was shifted to linearized region as large as 4 Oe. As shown in real device, MR response curve was in good agreement with the simulation results. As a result of experimental data of reproducing output signal in real device, it retained normal sinusoidal waveforms in 1~4 Oe external magnetic field. In this magnetic field region, the fabricated heads with tri-layered MR element can be operated with good reproduced characteristics. This will be beneficial to the use of efficient processes of manufacturing elements and the vacuum deposition techniques which control thin film properties.