• Journal of Bio-Environment Control
• /
• v.22 no.4
• /
• pp.427-431
• /
• 2013

Paprika fruits should be stored and distributed at above $7^{\circ}C$ to prevent chilling injury but the small amount of paprika that transports with other horticultural products in refrigerated container by ship usually stored less than $5^{\circ}C$ for other products. In this case, paprika fruits cannot help exposing chilling temperature, so that the paprika must be lost marketable value during a long period of transfer. This study was conducted to compare the alleviated effects of high $CO_2$ treatment (passive MAP), heat (hot water dipping), and UVc treatment on chilling injury of paprika fruits due to low temperature storage, and also to decide if these treatments can be used for transporting under $5^{\circ}C$. After each treatment the paprika were put in the low temperature storage ($4^{\circ}C$) for 20 days and afterwards change the in room temperature ($20^{\circ}C$) for 5 days. The fresh weight loss of all the treatments except the high $CO_2$ treatment showed around 7~12% after 25 days of storage and the ethylene concentration showed periodical increases and decreases as around 3 ${\mu}l/l$. The $CO_2$ concentration was rapidly increased 33% carbon dioxide in high $CO_2$ treatment during room temperature storage after cold storage for 20 days. The firmness which is key quality characteristics during storage and is decreasing caused by chilling injury was not significantly different among all treatments. However, the firmness of stored paprika was maintained highest in the treated with hot water dipping. Therefore, HWD and UVc treatment that showed 60% of electrolyte leakage in the $4^{\circ}C$ control (chilling injury control) and similar level with the $7^{\circ}C$ control (non-chilling injury control) would be effective to alleviate chilling injury in the stored paprika.

• Journal of Bio-Environment Control
• /
• v.20 no.3
• /
• pp.233-240
• /
• 2011

We evaluated the changes of fruit quality factors and the incidence of physiological disorders during the periods of high temperature environment in 'Wonhwang' and 'Whasan' pears to determine appropriate harvest time for exportation. In 'Wonhwang' pears, the fruits harvested at 130 days after full bloom (DAFB) showed 31.3 and 17.6N of flesh firmness after 5 and 10 days after simulated marketing at $30^{\circ}C$, respectively, while those of the fruits harvested at 135 DAFB lowered to 16.7 or 6.9N, respectively. Whereas, 'Whasan' pear showed higher firmness during 14 days of high marketing condition than 'Wonhwang' pears which represented 30.4, 26.5 and 21.6N in the fruits harvested 145, 150 and 155 DAFB, respectively. Higher soluble solid contents and lower acidity values observed in the late harvested fruits in both cultivar along with increased marketing period at $30^{\circ}C$. Late harvested 'Wonhwang' pears showed higher respiration rate and ethylene production than early harvested ones, while those of 'Whasan' pears showed lower values regardless of fruit maturity which represented less than 50% of 'Wonhwang' pears. The incidence of physiological disorders such as internal browning, water soaking, flesh spot decay, core breakdown and pithiness appeared more severely in the fruits of 'Wonhwang' in accordance with the progress of high temperature marketing and fruit maturity. Whereas, those symptoms were occurred only after 14 days of prolonged marketing time in 'Whasan' pears. Consequently, it was needed to pay more attention to determine the ripeness when the fruits exported to the country with high temperature environment, especially in the fruits of 'Wonhwang' pears showing rapid quality loss and severe physiological disorders.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.7 no.1
• /
• pp.1-7
• /
• 2009

This study has been focused on determining the chemical composition of $^{14}C$ - in terms of both organic and inorganic $^{14}C$ contents - in reactor coolant from 3 different PWR's reactor type. The purpose was to evaluate the characteristic of $^{14}C$ that can serve as a basis for reliable estimation of the environmental release at domestic PWR sites. $^{14}C$ is the most important nuclide in the inventory, since it contributes one of the main dose contributors in future release scenarios. The reason for this is its high mobility in the environment, biological availability and long half-life(5730yr). More recent studies - where a more detailed investigation of organic $^{14}C$ species believed to be formed in the coolant under reducing conditions have been made - show that the organic compounds not only are limited to hydrocarbons and CO. Possible organic compounds formed including formaldehyde, formic acid and acetic acid, etc. Under oxidizing conditions shows the oxidized carbon forms, possibly mainly carbon dioxide and bicarbonate forms. Measurements of organic and inorganic $^{14}C$ in various water systems were also performed. The $^{14}C$ inventory in the reactor water was found to be 3.1 GBq/kg in PWR of which less than 10% was in inorganic form. Generally, the $^{14}C$ activity in the water was divided equally between the gas- and water- phase. Even though organic $^{14}C$ compound shows that dominant species during the reactor operation, But during the releasing of $^{14}C$ from the plant stack, chemical forms of $^{14}C$ shows the different composition due to the operation conditions such as temperature, pH, volume control tank venting and shut down chemistry.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.667-678
• /
• 2002

In this paper, a new radiating structure with a multi-layered two-dimensional metallic disk array was proposed for shaping the flat-topped element pattern. It is an infinite periodic planar array structure with metallic disks finitely stacked above the radiating circular waveguide apertures. The theoretical analysis was in detail performed using rigid full-wave analysis, and was based on modal representations for the fields in the partial regions of the array structure and for the currents on the metallic disks. The final system of linear algebraic equations was derived using the orthogonal property of vector wave functions, mode-matching method, boundary conditions and Galerkin's method, and also their unknown modal coefficients needed for calculation of the array characteristics were determined by Gauss elimination method. The application of the algorithm was demonstrated in an array design for shaping the flat-topped element patterns of $\pm$20$^{\circ}$ beam width in Ka-band. The optimal design parameters normalized by a wavelength for general applications are presented, which are obtained through optimization process on the basis of simulation and design experience. A Ka-band experimental breadboard with symmetric nineteen elements was fabricated to compare simulation results with experimental results. The metallic disks array structure stacked above the radiating circular waveguide apertures was realized using ion-beam deposition method on thin polymer films. It was shown that the calculated and measured element patterns of the breadboard were in very close agreement within the beam scanning range. The result analysis for side lobe and grating lobe was done, and also a blindness phenomenon was discussed, which may cause by multi-layered metallic disk structure at the broadside. Input VSWR of the breadboard was less than 1.14, and its gains measured at 29.0 GHz. 29.5 GHz and 30 GHz were 10.2 dB, 10.0 dB and 10.7 dB, respectively. The experimental and simulation results showed that the proposed multi-layered metallic disk array structure could shape the efficient flat-topped element pattern.

• Korean Journal of Microbiology
• /
• v.53 no.2
• /
• pp.83-96
• /
• 2017

A constructed sea stream in Yeongdo, Busan, Republic of Korea is mostly static due to the lifted stream bed and tidal characters, and receives domestic wastewater nearby, causing a consistent odor production and water quality degradation. Bioaugmentation of a microbial consortium was proposed as an effective and economical restoration technology to restore the polluted stream. The microbial consortium activated on site was augmented on a periodic basis (7~10 days) into the most polluted site (Site 2) which was chosen considering the pollution level and tidal movement. Physicochemical parameters of water qualities were monitored including pH, temperature, DO, ORP, SS, COD, T-N, and T-P. COD and microbial community analyses of the sediments were also performed. A significant reduction in SS, COD, T-N, and COD (sediment) at Site 2 occurred showing their removal rates 51%, 58% and 27% and 35%, respectively, in 13 months while T-P increased by 47%. In most of the test sites, population densities of sulfate reducing bacterial (SRB) groups (Desulfobacteraceae_uc_s, Desulfobacterales_uc_s, Desulfuromonadaceae_uc_s, Desulfuromonas_g1_uc, and Desulfobacter postgatei) and Anaerolinaeles was observed to generally decrease after the bioaugmentation while those of Gamma-proteobacteria (NOR5-6B_s and NOR5-6A_s), Bacteroidales_uc_s, and Flavobacteriales_uc_s appeared to generally increase. Aerobic microbial communities (Flavobacteriaceae_uc_s) were dominant in St. 4 that showed the highest level of DO and least level of COD. These microbial communities could be used as an indicator organism to monitor the restoration process. The alpha diversity indices (OTUs, Chao1, and Shannon) of microbial communities generally decreased after the augmentation. Fast uniFrac analysis of all the samples of different sites and dates showed that there was a similarity in the microbial community structures regardless of samples as the augmentation advanced in comparison with before- and early bioaugmentation event, indicating occurrence of changing of the indigenous microbial community structures. It was concluded that the bioaugmentation could improve the polluted water quality and simultaneously change the microbial community structures via their niche changes. This in situ remediation technology will contribute to an eco-friendly and economically cleaning up of polluted streams of brine water and freshwater.

• Proceedings of the KSEEG Conference
• /
• 2001.05b
• /
• pp.42-63
• /
• 2001

The detail survey on the Songsanri tomb site including the Muryong royal tomb was carried out during the period from May 1 , 1996 to April 30, 1997. A quantitative analysis was tried to find changes of tomb itself since the excavation. Main subjects of the survey are to find out the cause of infiltration of rain water and groundwater into the tomb and the tomb site, monitoring of the movement of tomb structure and safety, removal method of the algae inside the tomb, and air controlling system to solve high humidity condition and dew inside the tomb. For these purposes, detail survery inside and outside the tombs using a electronic distance meter and small airplane, monitoring of temperature and humidity, geophysical exploration including electrical resistivity, geomagnetic, gravity and georadar methods, drilling, measurement of physical and chemical properties of drill core and measurement of groundwater permeability were conducted. We found that the center of the subsurface tomb and the center of soil mound on ground are different 4.5 meter and 5 meter for the 5th tomb and 7th tomb, respectively. The fact has caused unequal stress on the tomb structure. In the 7th tomb (the Muryong royal tomb), 435 bricks were broken out of 6025 bricks in 1972, but 1072 bricks are broken in 1996. The break rate has been increased about 250% for just 24 years. The break rate increased about 290% in the 6th tomb. The situation in 1996 is the result for just 24 years while the situation in 1972 was the result for about 1450 years. Status of breaking of bircks represents that a severe problem is undergoing. The eastern wall of the Muryong royal tomb is moving toward inside the tomb with the rate of 2.95 mm/myr in rainy season and 1.52 mm/myr in dry season. The frontal wall shows biggest movement in the 7th tomb having a rate of 2.05 mm/myr toward the passage way. The 6th tomb shows biggest movement among the three tombs having the rate of 7.44mm/myr and 3.61mm/myr toward east for the high break rate of bricks in the 6th tomb. Georadar section of the shallow soil layer represents several faults in the top soil layer of the 5th tomb and 7th tomb. Raninwater flew through faults tnto the tomb and nearby ground and high water content in nearby ground resulted in low resistance and high humidity inside tombs. High humidity inside tomb made a good condition for algae living with high temperature and moderate light source. The 6th tomb is most severe situation and the 7th tomb is the second in terms of algae living. Artificial change of the tomb environment since the excavation, infiltration of rain water and groundwater into the tombsite and bad drainage system had resulted in dangerous status for the tomb structure. Main cause for many problems including breaking of bricks, movement of tomb walls and algae living is infiltration of rainwater and groundwater into the tomb site. Therefore, protection of the tomb site from high water content should be carried out at first. Waterproofing method includes a cover system over the tomvsith using geotextile, clay layer and geomembrane and a deep trench which is 2 meter down to the base of the 5th tomb at the north of the tomv site. Decrease and balancing of soil weight above the tomb are also needed for the sfety of tomb structures. For the algae living inside tombs, we recommend to spray K101 which developed in this study on the surface of wall and then, exposure to ultraviolet light sources for 24 hours. Air controlling system should be changed to a constant temperature and humidity system for the 6th tomb and the 7th tomb. It seems to much better to place the system at frontal room and to ciculate cold air inside tombs to solve dew problem. Above mentioned preservation methods are suggested to give least changes to tomb site and to solve the most fundmental problems. Repairing should be planned in order and some special cares are needed for the safety of tombs in reparing work. Finally, a monitoring system measuring tilting of tomb walls, water content, groundwater level, temperature and humidity is required to monitor and to evaluate the repairing work.

• Journal of Korean Society of Forest Science
• /
• v.105 no.3
• /
• pp.275-283
• /
• 2016

The objective of this study was to examine carbon dynamics with biomass, soil $CO_2$ efflux, litter and root decomposition after tree density control in young Pinus densiflora stands. The stands were established with 50% thinning, clear-cut, and control stands with three pseudo-replicated plots and a bare soil plot in 8-year-old Pinus densiflora nursery field. Monthly measurements were conducted from March 2012 to February 2014 and aboveground biomass and coarse-roots were estimated by derived allometric equations. Average diameter growth at root collar in control and thinned was 0.89 cm and 1.48 cm per year, respectively, and the diameter growth of control stand was significantly higher than that of thinned stands (p<0.05). Total biomass was estimated to 5.17, $4.85kg\;C\;m^{-2}$ per year in control and thinned, respectively. Annual soil $CO_2$ efflux in control, thinned, clear cut, and bare soil was 3.71, 3.90, 4.17, $4.56kg\;CO_2\;m^{-2}\;yr^{-1}$, respectively and removing trees significantly increased soil $CO_2$ efflux (p<0.05). Net Ecosystem Production (NEP) was 1.57, 1.36, -0.67, $-1.25kg\;C\;m^{-2}\;yr^{-1}$ in control, thinned, clear cut and bare soil in the young Pinus densiflora stands. NEP was significantly decreased by removing trees. Thinning increased diameter at root collar and carbon of individual tree and recovered 86% of carbon removed by thinning after one-year. In addition, soil $CO_2$ efflux increased and NEP increased by thinning. Results of this study, tree density control such as thinning increased the carbon storage and growth of the young Pinus densiflora stands.

• The Korean Journal of Nuclear Medicine
• /
• v.35 no.5
• /
• pp.334-341
• /
• 2001

Purpose: Ascorbic acid us known to act as an antioxidant. Therefore, it can be used in increasing the efficiency of radiochemical labeling of Technetium-99m setamibi by inhibition of oxidation of $Sn^{2+}$ at low concentration. We intended to estimate the efficiency of radiochemical labeling and the stability of the newly formed formulation when ascorbic acid was added to a commercial kit. Materials and Methods: Synthesis of sestamibi was performed according to Dong-A's patent procedure (No.10-2001-0012877). First, we undertook a study to evaluate the efficiency of radiochemical labeling of sestamibi containing ascorbic acid. The stability of the vials was assessed using either $7.5{\mu}g\;or\;75{\mu}g$ of ascorbic acid, added to commercial vials under the accelerated condition(Temp : $40^{\circ}C{\pm}2^{\circ}C$, Relative humidity : $75{\pm}5%$). Results: Sestamibi was synthesized in overall 35-40% yield over 5 steps from a commercially available methallyl chloride as a starling material. When ascorbic acid was added, the efficiency of radiochemical labeling was maintained compared to the vial with no ascorbic acid. The accelerated test showed that the addition of ascorbic acid inhibited the oxidation of $Sn^{2+}$ ion by antioxidation mechanism. Also, the efficiency of radiochemical labeling of this vial after 9 months was nearly the same as the starting point. Therefore, the storage period of the kit is likely to be extended. Taken together, it suggests that the addition of ascorbic acid as a stabilizer is desirable. Conclusion: To increase the stability of a sestamibi cold kit, it is desirable to add ascorbic acid as a stabilizer to the commercial formulation.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.04a
• /
• pp.148-149
• /
• 2000

황금배는 1967년에 신고에 이십세기를 교배하여 1977년 1차선발과 1982년 2차선발을 거 쳐 1984년 최종선발, 명명한 품종으로, 당도가 높고 육질이 부드러워서 최근 몇년 사이에 캐 나다, 미국, 호주, 그리고 유럽 지역에서의 수요가 급증하고 있는 수출전망이 매우 밝은 품 종 중의 하나이다(92년 재배면적 lOha 수출량 5. 8M/T, 95년 재배면적 150ha 수출량 2 200.6M/T), 황금배는 비교적 대과이고 과형은 원형에 가까운 편원형으로서 사과 골든처럼 과피가 황금색이고 과육은 연황백색으로 투명하며 보기에 극히 미려한 특징이 있다. 아울러 육질이 유연치밀하고 과즙이 극히 많으며 당도가 높아 13$^{\circ}$ Bx이상, 15도 Bx까지 측정되는 둥 감산이 적화되어 맛이 극히 우수하다. 그러나 이러한 황금배는 동녹, 흑반병 등 병충해로 인한 상품가치의 하락으로 현재 수요를 충족시키지 못하고 있는 실정이다. 1 16세기부터 씌워진 과실봉지는 초기 병해충을 방지할 목적만으로 사용되어 왔지만, 현 재는 방균과 방충의 효과와 함께 자연현상의 최적화를 위한 차광성, 발수성, 투기성을 조절 하며 과실의 외관까지 영향을 미치는 바, 과실봉지의 기능성 부여를 위해서는 고도의 기술 력이 요구되고 있다 하겠다. 상기한 배에 방균방충처리된 과설봉지를 씌워서 재배하면 농 약 살포횟수를 줄이고 배에 농약이 직접 묻지 않아 배의 농약오염을 예방할 수 있으며, 봉 지 안으로의 해충이나 균의 침투를 원천적으로 봉쇄할 수 있다. 그러나 기존의 황금배용 봉 지는 비록 기타 병충해 피해를 방지하는 효과는 있었으나, 동녹을 억제하는 효력이 다소 미 흡하였다. 과피의 비정상적인 코르크화로 인해 발생하는 동녹은 과피의 물리적 할렬과 생리적 장 해에 의해 발생하는 것으로 알려져 있다(永澤 1940). 과실이 비대해짐에 따라 과피의 기공 (과점)이 할렬하면서 코르크화가 진행되는데 그 발생정도나 시기는 배의 품종에 따라 다르 나 일반적으로 코르크화는 기상조건, 특히 습도와 밀접한 관련이 있다고 알려져 있다 황금 배의 재배에 봉지를 적용하면 일반적으로 과피의 코르크화가 억제되는데 그러한 이유는 다 음과 같이 설명할 수 있다. 과실은 하루를 주기로 하여 수축과 팽창을 반복하면서 비대화하 는데 이러한 현상은 과실 내의 수분 조건에 따르는 것으로, 봉지재배의 경우 무대재배보다 단기간에 변화되는 습도의 범위가 좁아 급변을 방지하기에 과점의 할렬이 완화될 수 있다. 즉, 봉지를 씌웅으로서 봉지 내의 대기 환경이 외기보다 안정적으로 유지되고 직사광선이나 농약 및 마찰로부터 과실을 보호해 주기에 동녹이 어느 정도 방지될 수 있는 것이다. 그러나 기존의 황금배봉지는 동녹의 정도를 완화시킬 뿐 완전히 방지할 수 없었으며, 봉지를 적 용한 재배조건에서의 동녹발생 기구를 정확히 이해하지 못했었기에 효과적으로 봉지의 기능 을 개선하는 것이 불가능하였다. 과설의 미려도는 과실의 맛과 함께 그 가치를 결정짓는 중요한 물성으로서 우리나라 황 금배 재배환경과 특성에 알맞은 배봉지의 제작이 선결될 때, 배 품질의 향상, 안정된 공급이 가능하게 될 것이며 아울러 농가의 수업증대와 수출 경쟁력 강화가 이루어질 수 있을 것으로 판단된다. 이러한 측면에서 황금배 재배농가가 당면한 동녹발생의 문제점을 신속한 해결 을 위한 새로운 기능성 국산 황금배 봉지의 개발이 절실히 요구되고 있다. 위와 같은 문제를 해결하기 위하여 본 연구에서는 과실봉지의 종류간에 동녹발생 정도 가 상이한 점에 예의 주시하여 다양한 봉지의 적용실험을 통해 다음과 같은 결과를 얻었다. 황금배의 동녹 발생 정도는 배봉지의 발수성과 투기 및 투습도에 의해 크게 영향받는다. 상기한 바와 같이 과점의 코르크화로 인해 동녹이 발생된다고 할 때, 봉지 내의 습기 및 웅결수의 양은 황금배의 동녹에 중대한 영향을 미친다. 태양광이 내려찍는 낮 시간동안 황 금배는 증산작용을 하며 습기를 배출하는데 봉지 내의 온도가 높은 낮 시간 동안 수분이 습기로 존재하지만 기온이 급격히 떨어지는 일몰 이후에는 상대습도가 높아짐에 따라 결로 현상으로 인해 응결수가 된다. 이때 응결수와 접촉한 과피는 건조한 상태보다 세균의 침입 이 용이할 뿐만 아니라 기공(과점)의 호홉에 지장이 초래됨에 따라 과점의 할렬이 더욱 조 장되어 코르크화를 유발하고 결과적으로 동녹이 발생한다고 판단된다. 따라서 만일에 봉지 의 투기, 투습도가 양호하여 봉지 내의 과다한 수분이 충분히 배출될 수 있었다면, 수분의 응결을 피하고 동녹을 완화시킬 수 있을 것이라 판단되었다.

• Korean Journal of Soil Science and Fertilizer
• /
• v.28 no.2
• /
• pp.165-175
• /
• 1995

To determine the effect of soil moisture stress on growth of barley and grain quality, a pot experiment was carried out for two barley varieties(Olbori and Chogangbori) by using large plastic pot(52cm in diameter and 55cm in depth) filled with sandy loam soil under rain-controlled open green house. By means of measuring soil water potential with micro tensiometer and gypsum block installed at 10cm in soil depth, soil moisture was controlled by sub-irrigation at several irigation points such as -0.05bar, -0.2bar, -0.5bar, -1.0bar, -5.0bar and -10.0bar in soil water potential. The lower soil water potential was controlled, the shorter length of stem and internode became, and the more narrow stem diameter was. Leaf area was significantly decreased when soil water potential was controlled lower than -0.5bar, although chlorophyll content of flag and first leaves was not changed so much. Weight of grain and ear was significantly decreased when soil water potential was lower than -5.0bar and the highest grain yield was obtaind in a plot where soil water potential was controlled at -0.2bar. However, the most efficient water use of Olbori and Chogangbori was obtained at -0.5bar and -1.0bar in water potentials, respectively. Crude protain content, maximum viscosity, consistency and ${\beta}$-glucan content of barley flour increased as soil water potential significantly decreased, especially below -5.0bar, but gelatination temperature decreased as soil water potential decreased.