• Journal of the Korean Magnetics Society
• /
• v.11 no.3
• /
• pp.134-140
• /
• 2001

Flux-gate magnetometer was developed in 1930's, and it has been widely used for the low magnetic field measurements. In this work, we have employed amorphous ribbon 2714A produced by Allied Chem. Co. as sensor core material. To develop low noise, low power consumption, and high reliability flux-gate magnetometer, we have measured ac magnetic properties depending on the annealing conditions. As quenched state amorphous core shows high noise level and ac magnetic properties were changed under the condition of accelerated aging test, but amorphous ribbon, which was annealed under 350 $\^{C}$ during 1 hour, shows low noise level of 0.1 nT in the frequency range of dc∼10 Hz which was 10 times better than the as quenched amorphous ribbon. Under accelerated aging test, ac magnetic properties such as squareness and coercivity of the annealed samples show higher reliability and approached to a certain limiting value as exponential function. We can see that high reliability and low noise flux-gate magnetometer could be developed, if we consider this ac magnetic properties change in the sensor design.

• Korean Journal of Crystallography
• /
• v.6 no.2
• /
• pp.141-157
• /
• 1995

Single crystals of TeO2 with large diameter were grown by Czochralski technique with auto-diameter control system. The ratio of crystal to crucible was 60-70%. The effect of critical pulling and rotation rate on the crystal quality was studied. Optimum growth parameters for high quality crystal pulling rate was less than 1.2 mm/hr. The solid-liquid interface was convex at the rotation rate of 10-23 rpm and concave at the rotation rate of more than 25 rpm, depending on the size of crystal and crucible. The platinum concentration in the melts is one of the main factors of the constitutional supercooling and thus the bubble entrapment in the growing crystal. Growth axis was confirmed to {110} direction during the whole growth procedure. Infrared spectrometric study and dislocation density measurment by chemical etching method on the grown crystal were performed. Finally, the reasons of cooperation of striations, inclusions, and optical inhomogeneities were discussed.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.1378-1382
• /
• 2005

여름철 집중강우시 유입되는 고탁수층은 저수지의 밀도성층으로 인하여 표수층 하부에 위치하며, 이를 적기에 배제하지 않을 경우에는 수평방향의 확산현상과 연직방향의 전도현상으로 인해 저수지 전역에 분포하게 되어, 탁수현상의 장기화를 유발한다. 이와 같은 탁수장기화에 대한 저수지내 대책의 하나로서 홍수유입후 탁도가 높은 물을 단기간동안 방류하고, 갈수기에는 탁도가 낮은 물을 방류하는 선택취수 기법을 적용할 수 있다. 임하댐의 경우, 2004년 태풍 '디앤무'와 태풍 '메기'로 인해 발생한 탁수를 선택취수를 통하여 조기에 배제함으로써 호내탁도를 저감시킨 바 있다. 그러나 이와 같은 고탁수 우선배제 기법은 반드시 하류하천의 영향범위를 사전에 분석검토하고, 하류하천의 수질현황을 고려한 합리적인 운영방안이 제시되어야 한다. 2004년 태풍 '디앤무' 발생직후의 댐방수로에서 170 NTU의 고탁수를 방류한 경우, 유하거리 250 km인 지점까지 30 NTU이상 유지된 바 있으며, 태풍 '메기'에 의한 고탁수 유입시, 임하댐 방류수 157 NTU, 안동댐 방류수 37 NTU인 경우에 임하댐 하류 113 km인 구미 선산 취수장까지 63 NTU의 탁도가 유지된 바 있다. 현재 임하댐의 경우, 하류하천으로의 방류수 수질을 모니터링할 수 있는 자동수질측정시스템이 발전취수탑 전면 1개소, 조정지댐 1개소에 설치되어 있다. 본 연구에서는 자동수질측정시스템과 연계하여 수질모형을 통하여 임하댐 하류하천인 낙동강 본류의 탁도관리시스템을 구축하고자 하였다. 환경부의 수질측정망 자료를 통하여 최근 3년간의 부유사농도의 변화양상을 분석하였으며, 태풍 직후의 낙동강 주요지점별 탁도측정자료를 이용하여 임하댐 고탁도방류에 의한 영향범위를 분석하였다. 또한 하천수질모형을 이용하여 탁수예측방법에 대하여 검토하였고, 이를 이용한 탁도관리시스템 구축을 위한 기본 방향을 제시하고자 한다.함께, 2단계에 (주)웹솔루스에서 자체적으로 설치 운영하고 있는 2개소의 하수관거 모니터링 관측시설, 그리고 안양시에서 운영하고 있는 5개소의 강우관측소와 7개소의 수위관측소를 모두 통합하여 실시간 자료를 제공하고 있다. 수위자료는 10분단위의 텍스트정보와 그래프형태로 지원되며, 검색기간 설정을 통해 원하는 기간내의 자료를 선별, 검색할 수 있다.. 또한 이와 같은 기초적인 정보를 바탕으로 하류하천의 탁수 피해를 최소화할 수 있는 선택취수탑의 운영방안을 수립할 수 있다 본 연구에서는 이를 위해 선택취수탑 주위의 성층흐름을 기존의 실험자료와 수치해석을 통하여 분석하였고, 온도성층구조나 취수구의 위치변화에 따른 방류수 수질특성을 조사하였다.쇄파대(artifical reef)와 같은 완충지대를 갖는 호안을 축조함으로써 월파량을 감소시키는 대안으로 제시하고자 한다. 본 연구 수행을 통해 태풍 내습시 발생 가능한 자연재해에 대한 사전 방지를 목적으로 태풍피해의 원인을 제시하고 이를 해결하여 현재의 방재대책이 항구적인 방재대책으로 전환될 수 있는 방안 마련의 기초 자료로 활용되기를 기대한다., L-arabinose, 및 D-galactose; 제3차(第三次) 가수분해물(加水分解物)(C)에서 L-rhamnose, D-xylose, L-arabinose 및 D-galactose, 비가수분해물(非加水分解物)(C')에서 D-xylose와 D-galactose를 검출(檢出)하였다. (4) 구성당(構成糖)의 형태(形態)와 구조(構造)를 밝히기 위(爲)해 polysaccharide C에 대한 periodate산화(酸化) 실험(實驗)을 하여 $C_5H_8O_4$당(當) periodate의 소비(消費)와 formic acid의 생성량(生成量)을 측정(測定)하였는데 periodate의 소비량(消費量)은 1.23 mole, formic acid의 생성량(生成量)

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.2
• /
• pp.143-150
• /
• 2010

Purpose: The purpose of this study is to fabricate the new zirconia block (CNU block) and to evaluate fit of core and porcelain veneered zirconia crown. Material and methods: The experimental blocks were fabricated from the commercial ytrria-stabilized zirconia powder (KZ-3YE Type A). The powder was uniaxial pressing and the green bodies were conducted using the Cold Isostatic Pressing. The zirconia blocks were presintered at $1040^{\circ}C$ and the final sintering was performed at $1450^{\circ}C$. The Kavo Everest ZS $blank{(R)}$ (KaVo, Biberach/ $Ri{\beta}$.) was used as a control group. The linear shrinkage of CNU block and Kavo block were compared. Twenty-one cores for porcelain veneered crowns were fabricated with CAD/CAM system ($Everest{(R)}$, Biberach/ $Ri{\beta}$.). Group I; seven cores fabricated from Kavo blocks, Group II; seven cores fabricated from CNU blocks, Group III; seven cores from CNU blocks and porcelain veneering for crowns. All specimens were cemented and sectioned into two planes; diagonal and bucco-lingual. The measurement of the marginal, internal, and occlusal fit was carried out using SEM ($S-4800^{(R)}$) at $30{\times}$. The results were analyzed by one-way ANOVA test. Results: The linear shrinkage of the CNU block and the KaVo block was 19.00% and 20.09%. The marginal gap of cores ($29.67{\pm}6.58{\mu}m$) fabricated from CNU blocks showed significantly smaller than that of the cores of Kavo blocks ($36.84{\pm}7.18{\mu}m$) (P < .05). The internal gaps of the porcelain veneered crowns ($32.23{\pm}6.33{\mu}m$) were larger than those of the other two groups ($37.57{\pm}6.81{\mu}m$ and $38.14{\pm}6.81{\mu}m$). Conclusion: No statistically significant difference was found in between experimental groups and control group. The experimental groups in marginal gap showed significantly smaller than the control group.

• Journal of Environmental Impact Assessment
• /
• v.29 no.6
• /
• pp.403-413
• /
• 2020

A mathematical model comprised with eight simultaneous quasi-linear partial differential equations was suggested to provide optimal chlorination strategy. Upstream weighted finite element method was employed to construct multidimensional numerical code. The code was verified against measured concentrations in three type of reactors. Boundary conditions and reaction rate were calibrated for the sixteen cases of experimental results to regenerate the measured values. Eight reaction rate coefficients were estimated from the modeling result. The reaction rate coefficients were expressed in terms of pH and temperature. Automatic optimal algorithm was invented to estimate the reaction rate coefficients by minimizing the sum of squares of the numerical errors and combined with the model. In order to minimize the concentration of chlorine and pollutants at the final usage sites, a real-time predictive control system is imperative which can predict the water quality variables from the chlorine disinfection process at the water purification plant to the customer by means of a model and operate the disinfection process according to the influent water quality. This model can be used to build such a system in water treatment plants.

• Polymer(Korea)
• /
• v.30 no.4
• /
• pp.298-304
• /
• 2006

Blends of poly (acrylic acid-co-maleic acid)(PAM) with poly (vinyl alcohol)(PVA) were obtained by solution blending. The blends were solvent-on to a film to examine thermo-mechanical properties and gas permeability. The transition temperatures $(T_g\;and\;T_m)$ of the blends remained constant regardless of PAM contents. However, the values of enthalpy changes corresponding to melting transition $({\Delta}H_m)$ and initial degradation temperature $({T_D}^i)$ were decreased with increasing PAM content. The values of ultimate strength and initial modulus gave the maximum value at the 12 wt% PAM then decreased with further increase of PAM content up to 15 wt%. To measure the gas permeability of the PVA/PAM blend films, the PVA blend solutions were coated onto both biaxially oriented propylene (BOPP) and poly (ethylene terephthalate)(PET) films. The oxygen transmission rate $(O_2\;TR)$ permeability values mono- tonically decreased with increasing PAM content. However, moisture vapor transmission rate was not affected by PAM content.

• The Journal of the Acoustical Society of Korea
• /
• v.22 no.3
• /
• pp.217-223
• /
• 2003

A novel cooling method induced by acoustic streaming generated by ultrasonic vibration at 30㎑ is presented. Ultrasonic vibration is obtained by piezoelectric devices and the maximum vibration amplitude of 50 m is achieved by including a horn, mechanical vibration amplifier in the system and making the complete system resonate. To investigate the enhancement of heat transfer capability of acoustic streaming, the temperature variations of heat source and air in the vicinity of heat source are measured in real-time. It is observed that acoustic streaming is instantly induced by ultrasonic vibration, resulting in the significant temperature drop due to the bulk air flow caused by acoustic streaming. In addition, it is observed that the cooling effect on the heat source is maximized when the gap between the ultrasonic vibrator and heat source coincides with the multiples of half-wavelength of the ultrasonic wave. This fact results from the resonance of the sound wave. The theoretical analysis of the dependence on the gap is also accomplished and verified by experiment. The advantage of the proposed cooling method by acoustic streaming is noise-free due to the ultrasonic vibration and maintenance-free because of the absence of moving parts. Moreover. This cooling method can be utilized to the nano and micro-electro mechanical systems, where the fan-based conventional cooling method can not be employed.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.4
• /
• pp.7-14
• /
• 2000

A Bi$_{4}$Ti$_{3}$O$_{12}$ (BIT) thin film is prepared by sol-gel method using acetate precursors and evaluated whether it could be applied to NVFRAM (Non-Volatile Ferroelectric RAM). The drying and the annealing temperature are 40$0^{\circ}C$ and $650^{\circ}C$, respectively and they are determined from the DT-TG (Differential Thermal-Thermal Gravimetric) analysis. The BIT thin film deposited on Pt/Ta/SiO$_{2}$/Si substrate shows orthorhombic perovskite phase. The grain size and the surface roughness are about 100 nm and 70.2$\AA$, respectively. The dielectric constant and the loss tangent at 10 KHz are 176 and 0.038, respectively, and the leakage current density at 100 ㎸/cm is 4.71 $mutextrm{A}$/$\textrm{cm}^2$. In the results of hysteresis loops measured at $\pm$250 ㎸/cm, the remanent polarization (Pt) and the coercive field (Ec) are 5.92 $\mu$C/$\textrm{cm}^2$ and 86.3 ㎸/cm, respectively. After applying 10$^{9}$ square pulses of $\pm$5V, the remanent polarization of the BIT thin film decreases as much as about 33% from 5.92 $\mu$C/$\textrm{cm}^2$ of initial state to 3.95 $\mu$C/$\textrm{cm}^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.177-177
• /
• 2007

ZnO는 3.36eV의 넓은 밴드캡을 가지는 II-IV족 반도체로써 태양전지, LED와 같은 광학적 소자로 이용이 기대가 되는 물질이다. 더욱이, 상온에서의 60meV에 해당하는 큰 엑시톤 에너지와 밴드캡 에지니어링이 가능하다는 장점 때문에 광학적 소자로 널리 이용되고 있는 GaN을 대체할 수 있는 물질로 주목을 받고 있다. 하지만, p-type ZnO는 형성이 어렵고 낮은 이동도와 케리어 농도의 특성을 보이고, 대기 중에 장시간 노출할 경우 n-type ZnO의 특성으로 돌아가는 불안정성을 보이고 있다. 최근에 몇몇의 연구자들에 의해 V족의 원소인 P(phosphorous), N(nitrogen), As(arsenic))를 도핑하여 p-type ZnO의 형성에 대한 논문이 발표되고 있다. 또한, V족 원소 중에 P는 p-type ZnO 형성에 효과적인 도핑 물질로 보고되 고 있다. 본 연구는 마그네트론 스퍼터링을 이용하여 다양한 온도에서 성장된 P도핑 ZnO 박막의 특성에 대해 연구하였다. P도핑된 ZnO 박막은 사파이어 기판에 buffer층을 사용한 Insulator 특성의 ZnO박막위에 400, 500, 600, $700^{\circ}C$에서 성장되 었다. 박막의 특성 분석에는 325nm의 파장을 가지는 He-Cd의 레이져 광원을 사용하여 10K의 저온 PL과 0.5T의 자기장을 사용한 van der Pauw configuration에 의한 Hall effect측정, 그리고 결정성 분석에는 XRD와 TEM을 이용하였다. 상온 Hall-effect 측정 결과, $400{\sim}600^{\circ}C$ 에서 성장된 박막은 n-type의 특성을 보였고, $700^{\circ}C$에서 성장된 Phosphorous 도핑 ZnO박막은 $1.19{\times}10^{17}$의 캐리어 농도를 가지는 p-type의 특성을 보였다. 그리고 XRD분석과 TEM분석을 통하여 박막의 성장온도가 증가 할수록 P도핑된 ZnO박막의 결정성이 향상되는 것을 알 수 있었다. 또한 10K의 저온 PL분석을 통해 p도핑에 의한 액셉터에 관련된 피크들을 관찰할 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.1
• /
• pp.94-104
• /
• 2009

It is urgently required to develop the production of fermentation-heat energy from the waste agricultural and forest biomass and its effective heat exchanging system for the supply of warm water to rural households and greenhouses. In this study 3 helical-type and 1 plate-type heat exchangers using 3 different waste biomasses [e.g. hardwood (HW) sawdust (100%), softwood (SW) sawdust : HW sawdust (50 : 50) and HW sawdust : grass (90 : 10)] were applied in order to find out the best heat recovery system. The heat exchanger was basically considered to improve the overall heat recovery efficiency, to minimize heat loss and to simplify manufacturing, assembling and breaking up the fermenting beds. The helical-type heat exchanger (HX-H3) installed in fermenting bed of HW sawdust : grass (90 : 10) showed relatively higher temperature profiles, in particular mid- and upper-parts than lower and surface parts during 45-day fermentation process. The maximum temperature was ranged from $40^{\circ}C$ to $65^{\circ}C$ with average $60^{\circ}C$. The water temperature of tank outlet was ranged to $33{\sim}48^{\circ}C$ during whole measuring periods. By the way plate-type one (HX-P) installed in same biomass compositional fermenting bed showed $64.5{\sim}76.5^{\circ}C$ at center part, and $43{\sim}56^{\circ}C$ and $42{\sim}58^{\circ}C$, water tank and tank outlet temperatures, respectively, during 100 day measurement. It could be concluded that the plate-type heat exchanger (HX-P) provides not only the effective heating for the rural households and greenhouses, but also having the best heat recovery performance, easy manufacturing, assembling and breaking up the systems.