• Korean Chemical Engineering Research
• /
• v.59 no.1
• /
• pp.127-137
• /
• 2021

Air emission charge for nitrogen oxide as a precursor of fine dust has been introduced and implemented within the country from 2020. Therefore, the development of economical combustion technology for NOx reduction has got more needed urgently. This study investigated the air-staging effect as a way to reduce the NOx during combustion of domestic unused forest biomass, recently possible to secure REC (Renewable Energy Certification) as a substitute for overseas wood pellets in a 0.1 MWth circulating fluidized bed combustion test-rig. Operating conditions were comparison with and without air-staging, the supply position of tertiary air (6.4 m, 8.1 m, 9.4 m in the combustor) and variation of air-staging ratio (Primary air:Secondary air:Tertiary air=91%:9%:0%, 82%:9%:9%, 73%:9%:18%). NO and CO concentrations in flue gas, profiles of temperature and pressure at the height of the combustion, unburned carbon in sampled fly ash and combustion efficiency on operating conditions were evaluated. As notable results, NO concentration with air-staging application under tertiary air supply at 9.4 m in the combustor reduced 100.7 ppm compared to 148.8 ppm without air-staging while, CO concentration increased from 52.2 ppm without air-staging to 99.8 ppm with air-staging. However, among air-staging runs, when tertiary air supply amount at 6.4 m in the combustor increased by air-staging ratio (Primary air:Secondary air:Tertiary air=73%:9%:18%), NO and CO concentrations decreased the lowest 90.8 ppm and 66.1 ppm, respectively. Furthermore, combustion efficiency at this condition was improved to 99.3%, higher than that (98.3%) of run without air-staging.

• Journal of Bio-Environment Control
• /
• v.30 no.1
• /
• pp.1-9
• /
• 2021

This study was conducted to examine the changes of photosynthesis, growth, chlorophyll contents and functional material contents in light intensity and EC concentration of wild baby leaf vegetable, Indian lettuce (Lactuca indica L. cv. 'Sunhyang') in DFT hydroponics. The cultivation environment was 25±1℃ of temperature and 60±5% of relative humidity in growth system. At 14 days after sowing, combination effect of light intensity (Photosynthetic Photon Flux Density (PPFD 100, 250, 500 µmol·m-2·s-1) and EC level (EC 0.8, 1.4, 2.0 dS·m-1) of nutrient solution was determined at the baby leaf stage. The photosynthesis rate, stomatal conductance, transpiration rate and water use efficiency of Indian lettuce increased as the light intensity increased. The photosynthesis rate and water use efficiency were highest in PPFD 500-EC 1.4 and PPFD 500-EC 2.0 treatment. The chlorophyll content decreased as the light intensity increased, but chlorophyll a/b ratio increased. Leaf water content and specific leaf area decreased as light intensity increased and a negative correlation (p < 0.001) was recognized. Plant height was the longest in PPFD 100-EC 0.8 and leaf number, fresh weight and dry weight were the highest in PPFD 500-EC 2.0. Anthocyanin and total phenolic compounds were the highest in PPFD 500-EC 1.4 and 2.0 treatment, and antioxidant scavenging ability (DPPH) was high in PPFD 250 and 500 treatments. Considering the growth and functional material contents, the proper light intensity and EC level for hydroponic cultivation of Indian lettuce is PPFD 500-EC 2.0, and PPFD 100 and 250, which are low light conditions, EC 0.8 is suitable for growth.

• Journal of Food Hygiene and Safety
• /
• v.36 no.6
• /
• pp.510-519
• /
• 2021

The purpose of this study was to investigate the effect of the microbial reduction and quality maintenance of the physical and chemical pretreatment of Allium monanthum. For physical treatment, handwash, bubble wash and ultrasonication were conducted at 50℃ and 60℃ for 1, 3 and 5 minutes, respectively, and for chemical treatment the sample was immersed in fumaric acid and acetic acid of 1.5% and 2% concentrations for 1, 3 and 5 minutes, respectively. As a result of the microorganism and quality analysis, 3 minutes of bubble wash was the most effective physical pretreatment in reducing fungi although the effect on reducing total viable bacterial was small. Furthermore, 5 minutes of ultrasonication at 60℃ significantly reduced microorganisms, but also resulted in the reduction of the a value of chromaticity, which cause the green color to fade. With chemical pretreatment, it was found that treating with fumaric acid was more effective in reducing the total viable bacteria and fungi than acetic acid. The result shows that 1.5% concentration of fumaric acid is the most effective with 3 minutes of treatment time. The quality of Allium monanthum were compared in the combination of the two most effective microorganism reduction pretreatments: 3 minutes of bubble wash (B3) and 3 minutes in 1.5% fumaric acid (F153). As a result of analyzing the quality characteristics over 9 days of storage at 4℃ after the treatments, it was revealed that the BF treatment is more effective in reducing fungi than the total viable bacteria. The results shows that the BF treatment is more effective in reducing total viable bacteria, whereas the F153 treatment is more effective in reducing fungi. Also, it was found that the 𝚫E value in BF was the lowest, whereas F153 treatment showed the green color faded. The maximum cohesiveness changed more significantly in the green stems than in the roots. On the 9th day of storage, the hardness of the green stem was found to be maintained at the highest level (P<0.05) after F153 treatment, whereas that of the roots decreased (P<0.05) since the 6th day after the bubble wash. Considering the reduction of microorganisms and the quality maintenance of Allium monanthum, the most effective pretreatment methods were 3 minutes in 1.5% fumaric acid for reducing microorganisms and maintaining color and maximum cohesiveness, and the combined process could also be effective if the expiration period is within 3 days.

• Journal of the Korean Chemical Society
• /
• v.66 no.2
• /
• pp.78-85
• /
• 2022

Natural white clay was treated with 6 M of H₂SO₄ and heated at 80℃ for 6 h under mechanical stirring and the resulting acid active clay was used as an adsorbent for the removal of Cs⁺ in water. The physicochemical changes of natural white clay and acid active clay were observed by X-ray Fluorescence Spectrometry (XRF), BET Surface Area Analyser and Energy Dispersive X-line Spectrometer (EDX). While activating natural white clay with acid, the part of Al₂O₃, CaO, MgO, SO₃ and Fe₂O₃ was dissolved firstly from the crystal lattice, which bring about the increase in the specific surface area and the pore volume as well as active sites. The specific surface area and the pore volume of acid active clay were roughly twice as high compared with natural white clay. The adsorption of Cs⁺ on acid active clay was increased rapidly within 1 min and reached equilibrium at 60 min. At 25 mg L^- of Cs⁺ concentration, 96.88% of adsorption capacity was accomplished by acid active clay. The adsorption data of Cs⁺ were fitted to the adsorption isotherm and kinetic models. It was found that Langmuir isotherm was described well to the adsorption behavior of Cs⁺ on acid active clay rather than Freundlich isotherm. For adsorption Cs⁺ on acid active clay, the Langmuir isotherm coefficients, Q, was found to be 10.52 mg g^-1. In acid active clay/water system, the pseudo-second-order kinetic model was more suitable for adsorption of Cs⁺ than the pseudo-first-order kinetic model owing to the higher correlation coefficient R² and the more proximity value of the experimental value q_e,exp and the calculated value q_e,cal. The overall results of study showed that acid active clay could be used as an efficient adsorbent for the removal of Cs⁺ from water.

• Journal of Bio-Environment Control
• /
• v.31 no.1
• /
• pp.28-34
• /
• 2022

This study was conducted to determine the changes in ginsenosides content according to additional UV-A, and UV-B LED irradiation before harvesting the ginseng sprouts. One-year-old ginseng seedlings (n=100) were transplanted in a tray containing a ginseng medium. The ginseng sprouts were grown for 37 days at a temperature of 20℃ (24h), a humidity of 70%, and an average light intensity of 80 µmol·m^-2·s^-1 (photoperiod; 24h) in a container-type plant factory. Ginseng sprouts were then transferred to a custom chamber equipped with UV-A (370 nm; 12.90 W·m^-2) and UV-B (300 nm; 0.31 W·m^-2) LEDs and treated for 3 days. Growth parameters and ginsenoside contents in shoot and root were conducted by harvesting on days 0 (control), 1, 2, and 3 of UV treatments, respectively. The growth parameters showed non-significant differences between the control and the UV treatments (wavelengths or the number of days). Ginsenoside contents of the shoot was highly improved by 186% in UV-A treatment compared to the control in 3 days of the treatment time. The ginsenoside contents of the roots was more improved in UV-A 1-day treatment and UV-B 3-day treatment, compared to the control by 171% and 160%, respectively. As a result of this experiment, it is thought that UV LED irradiation before harvesting can produce sprout ginseng with high ginsenoside contents in a plant factory.

• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.535-543
• /
• 2022

A CPFD (Computational particle fluid dynamics) model of solar fluidized bed receiver of silicon carbide (SiC: average d_p=123 ㎛) particles was established, and the model was verified by comparing the simulation and experimental results to analyze the effect of particle behavior on the performance of the receiver. The relationship between the heat-absorbing performance and the particles behavior in the receiver was analyzed by simulating their behavior near bed surface, which is difficult to access experimentally. The CPFD simulation results showed good agreement with the experimental values on the solids holdup and its standard deviation under experimental condition in bed and freeboard regions. The local solid holdups near the bed surface, where particles primarily absorb solar heat energy and transfer it to the inside of the bed, showed a non-uniform distribution with a relatively low value at the center related with the bubble behavior in the bed. The local solid holdup increased the axial and radial non-uniformity in the freeboard region with the gas velocity, which explains well that the increase in the RSD (Relative standard deviation) of pressure drop across the freeboard region is responsible for the loss of solar energy reflected by the entrained particles in the particle receiver. The simulation results of local gas and particle velocities with gas velocity confirmed that the local particle behavior in the fluidized bed are closely related to the bubble behavior characterized by the properties of the Geldart B particles. The temperature difference of the fluidizing gas passing through the receiver per irradiance (∆T/I_DNI) was highly correlated with the RSD of the pressure drop across the bed surface and the freeboard regions. The CPFD simulation results can be used to improve the performance of the particle receiver through local particle behavior analysis.

• Korean Journal of Food Science and Technology
• /
• v.53 no.4
• /
• pp.486-494
• /
• 2021

A rice (Oryza sativa L.) cultivar of the SPP (stakeholder participatory program) and ordinary rice were characterized based on water-absorption properties and cooked rice texture. During rice soaking, the rice grain transformed from transparent to opaque (white), indicating that water molecules diffused into the rice grain during soaking. In addition, cracks in the internal structure of soaked rice gradually increased with an increase in soaking time. Water absorption increased rapidly up to 20 min, but no increment was observed after 30 min of soaking. At this point, the entire areas of the soaked rice grain turned white, indicating that water absorption had reached saturation. SPP rice showed lower hardness and higher stickiness in its cooked form than ordinary rice, suggesting that SPP rice could be a more preferable choice than ordinary rice. Furthermore, cooked SPP rice was more edible in terms of hardness and stickiness after being kept warm for 12 h than ordinary rice. These results indicated that cooked SPP rice exhibited slow retrogradation and improved taste.

• Journal of the Korean Chemical Society
• /
• v.65 no.3
• /
• pp.197-202
• /
• 2021

In this study, activated clay treated with H₂SO₄ (20% by weight) and heat at 90 ℃ for 8 h for acid white soil was used as an adsorbent for the removal of PO₄^3--P in water. Prior to the adsorption experiment, the characteristics of activated clay was examined by X-ray Fluorescence Spectrometry (XRF) and BET surface area analyser. The adsorption of PO₄^3--P on activated clay was steeply increased within 0.25 h and reached equilibrium at 4 h. At 5 mg/L of low PO₄^3--P concentration, roughly 98% of adsorption efficiency was accomplished by activated clay. The adsorption data of PO₄^3--P were introduced to the adsorption isotherm and kinetic models. It was seen that both Freundlich and Langmuir isotherms were applied well to describe the adsorption behavior of PO₄^3--P on activated clay. For adsorption PO₄^3--P on activated clay, the Freundlich and Langmuir isotherm coefficients, K_F and Q, were found to be 8.3 and 20.0 mg/g, respectively. The pseudo-second-order kinetics model was more suitable for adsorption of PO₄^3--P in water/activated clay system owing to the higher correlation coefficient R² and the more proximity value of the experimental value q_e,exp and the calculated value q_e,cal than the pseudo-first-order kinetics model. The results of study indicate that activated clay could be used as an efficient adsorbent for the removal of PO₄³-P from water.

• Resources Recycling
• /
• v.31 no.1
• /
• pp.65-77
• /
• 2022

A study was conducted in Korea on the leaching behavior and possibility of recovery of vanadium and other valuable metals from domestic vanadium titanomagnetite (VTM) by direct acid leaching. In this study, a VTM concentrate containing 0.8% V₂O₅ was used, and the ratio of magnetite to ilmenite was calculated as 1.9:1 by using the HSC program. The leaching behavior of vanadium from the VTM was similar to that of iron, and it was affected by the concentration of sulfuric acid and temperature. Further, titanium could be leached in the form of TiOSO₄ at a temperature higher than 75℃. To improve the leaching efficiency of V, Fe, and Ti in VTM, reductive sulfuric acid and oxidative sulfuric acid leaching were performed. When Na₂SO₃ was used as a reducing agent, the leaching rate of vanadium was 80% of that in that case of leaching by sulfuric acid. Similarly, the leaching rate of titanium increased from 20% to 50%. When Na₂S₂O₈ was used as an oxidation agent, most of the vanadium was leached, and the main residue found by XRD analysis was ilmenite. In studies on the possibility of recovering valuable metals, the selective extraction of metals is hardly achieved by solvent extraction from oxidation leaching solutions; however, in this study, Cyanex 923, a solvation extractant from reductive leaching solutions, could selectively extract Ti.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.48 no.1
• /
• pp.55-64
• /
• 2022

The potassium cream soap with fatty acid called cleaning foam has a crystal gel structure, and unlike an emulsion system, it is weak to shear stress and shows characteristics that are easily separated under high temperature storage conditions. The crystal gel structure of cleansing foams is significantly influenced by the nature and proportion of fatty acids, degree of neutralization, and the nature and proportion of polyols. In order to investigate the effect of these parameters on the crystal gel structure, a ternary system consisting of water/KOH/fatty acid was investigated in this study. The investigation of differential scanning calorimeter (DSC) revealed that the eutectic point was found at the ratio of myristic acid (MA) : stearic acid (SA) = 3 : 1 and ternary systems were the most stable at the eutectic point. However, the increase in fatty acid content had little effect on stability. On the basis of viscosity and polarized optical microscopy (POM) measurements, the optimum degree of neutralization was found to be about 75%. The system was stable when the melting point (T_m) of the ternary system was higher than the storage temperature and the crystal phase was transferred to lamellar gel phase, but the increase in fatty acid content had little effect on stability. The addition of polyols to the ternary system played an important role in changing the T_m and causing phase transition. The structure of the cleansing foams were confirmed through cryogenic scanning electron microscope (Cryo-SEM), small and wide angle X-ray scattering (SAXS and WAXS) analysis. Since butylene glycol (BG), propylene glycol (PG), and dipropylene glycol (DPG) lowered the T_m and hindered the lamellar gel formation, they were unsuitable for the formation of stable cleansing foam. In contrast, glycerin, PEG-400, and sorbitol increased the T_m, and facilitated the formation of lamellar gel phase, which led to a stable ternary system. Glycerin was found to be the most optimal agent to prepare a cleansing foam with enhanced stability.