• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.6
• /
• pp.604-608
• /
• 2015

In this paper, we study the characteristics of heat transfer for an insulated multi-core tube using glass wool as an insulator for the multi-core tube. By performing experiments and modeling, we examine the variations in the temperature characteristics of hydraulic oil inside the multi-core tube with atmosphere temperature, inlet temperature, and the flow rate of hydraulic oil for the insulated multi-core tube that we developed. When the minimum inlet flow rate of hydraulic oil employed within the scope of the research is 0.29 l/min, the temperature difference obtained in the experiments and numerical analysis was a maximum of $3^{\circ}C$. For a constant atmospheric temperature, as the inlet temperature of the hydraulic oil increases, the outlet temperature of the hydraulic oil will also increase, regardless of its inlet flow rate. Further, when the inlet flow rate of the hydraulic oil is more than 1.01 l/min, the effect of the atmospheric temperature on the temperature drop of the hydraulic oil is low.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.3
• /
• pp.495-503
• /
• 2017

Wax components can be precipitated when surrounding temperature decreases below wax precipitation temperature (WAT). WAT as well as pour point are important characteristics to evaluate the behavior of waxy oils. In this study, qualitative and quantitative evaluations of waxes in waxy model oils were presented after determining WAT and pour point. In case of anhydrous waxy model oils, ASTM D2500 may be most useful to determine WAT because of the transparent nature of model oils. With same apparatus, ASTM D97 is also applicable to determine the pour point of waxy oils in a serial determination. In case of emulsified model oils, however, it is difficult to measure WAT because of its opaque nature. This study employed FTIR spectroscopy to determine wax precipitation temperature and discussed the effect of emulsion state regarding the values of WAT. Further study would be needed to conclude the effect of water contents to WAT values in case of emulsified waxy oil.

• 기계와재료
• /
• v.22 no.1
• /
• pp.54-64
• /
• 2010

공작기계의 고속화, 다축화, 복잡화에 따른 열변형 오차가 공작기계에서 발생하는 오차의 대부분을 차지하고 있다. 이러한 열변형 오차를 최소화 하기 위해 공작기계의 발열부에 차가운 오일을 공급하여 냉각함으로써, 열변형을 제거하는 장치가 오일쿨러이다. 오일쿨러는 제어 방법에 따라 On-off, 가스 바이패스, 인버터 방식 등이 사용된다. 초정밀 공작기계에는 주로 가스 바이패스 및 인버터 방식이 사용되는데, 인버터 방식의 경우 고가(高價)인 관계로 주로 옵션 형태로 사용된다. 가스 바이패스 방식 오일쿨러는 인버터 방식에 비해 가격이 저렴하고 구조가 간다하며 정밀한 온도제어를 할 수 있지만 부하가 낮은 경우 구조적인 한계로 인해 온도제어 불안정을 발생시킨다. 본 연구에서는 기존 바이패스 방식 오일쿨러에서 나타나는 문제점을 해결하고 보다 정밀한 온도제어를 위해 2개의 전자밸브를 갖는 듀얼 밸브 방식 오일쿨러 시스템을 개발하였다. 개발된 듀얼 밸브 오일쿨러 시스템의 성능검증을 위해 정격운전, DIN 8602 규격, ISO/DIS 230-3 운전모드에서 성능을 비교/분석하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.536-540
• /
• 2018

As the performance of engines improves, the temperature of engines is increasing, resulting in a high piston temperature. An excessively high piston temperature may result in torque drop or engine failure. An oil jet is used to reduce the piston temperature. In this study, to monitor the effect of oil jet, a templug was used to measure the piston temperature. A templug is a kind of sensor and the hardness of the templug changes according to the piston temperature. Using a templug, the maximum temperature of the piston was measured with and without an oil jet. The piston temperature was lowered using the oil jet. The highest temperature region changed from the center crown to the front/rear area. In addition, the temperature difference between the highest and lowest regions became smaller.

• Journal of Energy Engineering
• /
• v.24 no.2
• /
• pp.1-8
• /
• 2015

Wax deposition hinders oil flow assurance. Huge amount of money and time were required for mitigation of wax deposition in the oil field. For prediction and mitigation of wax deposition problem, Wax Appearance Temperature(WAT), which is the temperature at which the first wax crystals start to form, needs to be measured in advance. There is a standard method which is optical way to measure the WAT of transparent oil. However, standard method cannot be applied to opaque oil which is common produced oil in the field. In this study, WAT of three transparent oil samples were measured using heat flux variation analysis, viscosity variation analysis and density variation analysis, and compared with WAT measured by standard method. As a result, WAT measured by density variation analysis is the more reliable than heat flux variation analysis and viscosity variation analysis. WAT of two opaque oils were measured using density variation analysis.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.12
• /
• pp.1067-1074
• /
• 2007

A temperature preconditioning that modulates the derivative of density with respect to temperature is proposed to improve the convergence characteristics of the preconditioned Euler equations. Flows in a two-dimensional channel with a 10% circular bump in the middle of the channel were calculated at different speeds. The numerical dissipation terms of the Roe’s FDS scheme according to the temperature preconditioning are derived. It is shown that the temperature preconditioning accelerates convergence of the preconditioned Euler equations.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2020.11a
• /
• pp.23-24
• /
• 2020

커피박을 FeCl₃·6H₂O로 전처리하여 제조한 자성 복합재의 유출유 회수 실험을 진행하였다. 전반적으로 사용하지 않은 디젤엔진 오일이 사용한 디젤엔진 오일보다도 오일 회수율이 높게 나타났고, 수중온도가 5℃일때보다도 25℃일 때 오일 회수량이 더 높게 나타났다. 실험 결과는 모든 온도에서 오일 회수량을 높이기 위해서는 FeCl₃·6H₂O 전처리 용액의 농도가 최소한 0.1 M은 되어야 함을 보여 주었다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.451-454
• /
• 2003

The Oil Coolers is very important unit for the stable thermal performance in machine tools, semiconductor equipments and high precision measuring systems. To select a proper oil cooler for the temperature control of core unit in a machine, not only cooling ability but also static and dynamic sensitivity of temperature sensors are considered. In this paper, the relationship between cooling ability and inflow oil temperature is identified. The cooling ability is increased with the increase of inflow oil temperature. The oil temperature control errors of a cooler are influenced by mainly sensitivity of temperature sensors and heating velocity in a machine. The validity of error cause analysis for temperature control is proved by real cooling experiments with inflow and outflow temperature sensors.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.2
• /
• pp.130-135
• /
• 2013

Recently, the needs of system performances such as working speed and processing accuracy in machine tools have been increased. Especially, the working speed increment generates harmful heat at both moving part of the machine tools and handicrafts. The heat is a main drawback to progress accuracy of the processing. Hence, a oil cooler to control temperature is inevitable for the machine tools. In general, two representative control schemes, hot-gas bypass and variable speed control of a compressor, have been adopted in the oil cooler system. In this paper, the compressor's speed are controlled to keep reference value of temperature at oil outlet. The precision processing of a machine tool is required for an oil cooler guaranteeing ${\pm}0.1^{\circ}C$ temperature control. But the oil cooler with precision temperature control is expensive. Therefore in this paper, instead of a on/off(relay) control method, a PID and phase angle electric power control method is proposed for the precision control of an oil cooler. The proposed controller is implemented and tested at the temperature of $23^{\circ}C$, $24^{\circ}C$ and $25^{\circ}C$.

• Journal of the korean Society of Automotive Engineers
• /
• v.17 no.3
• /
• pp.11-18
• /
• 1995

본 논문에서는 주철 라이너를 삽입한 알루미늄 블럭 엔진 개발과정에서 주조 불량이 발생하였을때, 냉각계에 일어나는 제반 현상을 분석하고, 이를 해결해 나가는 과정을 기술하였다. 이를 위하여 주철 블럭과 알루미늄 블럭을 장착한 엔진의 피스톤 온도와 블럭의 열유속, 열정산을 측정하였다. 측정한 결과는 다음과 같다. 1. 알루미늄 블럭 제작시 주철 라이너와 알루미늄 블럭 사이에 공기층이 크거나, 용탕 충진이 불완전한 주조 불량이 발생하면 열접촉 저항이 커져 엔진 열전달 경로에 큰 영향을 준다. 2. 알루미늄 블럭 제작시 주조 불량이 발생하면 피스톤에서 라이너로의 전열량이 줄어듦에 따라 냉각수로의 전열량은 감소하는데, 6,000rpm, 전부하에서 알루미늄 블럭의 출력 대비 냉각수로의 방열량의 비는 38.3%이고, 주철 블럭은 44.1%이다. 3. 알루미늄 블럭 제작시 주조 불량이 발생하면, 피스톤 온도가 15-20.deg.C 정도 상승하여 피스톤 손상을 유발시킬 수 있다. 4. 알루미늄 블럭의 주조가 완벽하게 되어 주철 라이너와 알루미늄 몸체 사이에서의 열접촉저항이 없어지면, 스토로크 방향에 따른 금속면 온도 분포가 균일하게 된다. 5. 실린더 라이너의 주조상태 개선없이 오일젯을 사용한 결과 피스톤의 온도를 만족할 만한 수준으로 감소시켰다. 6. 6000rpm, 전부하에서 오일젯 적용시 출력 대비 냉각수로의 방열량의 비가 38.3%에서 36.2%로 감소하고, 출력대비 오일로의 방열량의 비는 9.6%에서 11.2%로 증가한다. 7. 오일젯 작용시 오일 펌프의 용량 증대와 오일 쿨러의 장착이 필수적이다.