• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.570-576
• /
• 2018

In reinforced concrete structures, the joints of ordinary rebars are usually lap joints, which are bound by binding wires with rebars, and mechanical joints by couplers. In domestic design standards (concrete design code), welded lap joints are restricted for ordinary rebars, but overseas standards allow welded lap joints of ordinary rebars through pre-heating. This study investigated the domestic and international standards/criteria and evaluated the fracture strength by performing the tensile test on the lap welded joint of SD400 grade rebars, which is used the most in the construction sites. The weld length of the specimen for weld lap joints is based on the minimum weld length (8d) given in the KS standard (KS B ISO 17660-1). According to AWS D1.4, the preheating temperature was set to $150^{\circ}C$ for D19 and below, and $260^{\circ}C$ for D22 and above. In the test results, the tensile strength of rebars with welded lap joints exceeded the required strength (125% of the yield strength) according to the concrete design code. To analyze the effect of preheating, the tensile strength of the welded rebars after preheating was not significantly different from that of the welded rebars without preheating. The carbon equivalent content (Ceq) of the rebars used in the test was 0.45% or less. Under AWS D1.4, no preheating is required if the carbon equivalent is less than 0.45%. All specimens with a welded lap length of 8d failed by a bar fracture. The effect of preheating was confirmed to be insignificant due to the low carbon equivalent of the rebar.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.573-580
• /
• 1998

Self-propagating high temperature synthesis (SHS) technique was used to synthesize the spinel phase of $MgAl_2O_4$ from MgO and Al powder. Thermit reaction products of MgO and Al, The reaction products were heat treated at the temperature $800^{\circ}C$ preheating. Processing factors such as DTA/TG, combustium product and maxium temperature, synthesis of MgO and Al from "$MgO+2Al+3/2O_2$\rightarrow$MgAl_2O_4$". An activation energy (${\Delta}H^{\circ}$)-264.8 kcal/mol and reaction of maxium temperature 5634 K was calculated to form a $MgAl_2O_4$ spinel from unreacted materials. Pellet were increased volume 6% after thermit reaction. reaction.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2006.05a
• /
• pp.295-297
• /
• 2006

전력수가 증가할수록 수분감소율과 부피감소율은 또한 급격한 형태로 감소하였으며, 2kW일때는 완만한 형태를 나타냈다. 또한 온도의 변화에 있어서도 예열기간은 온도가 증가함을 알 수 있으나, 항률건조단계부터는 온도의 변화가 거의 없는 것으로 나타났다.

• Journal of Energy Engineering
• /
• v.13 no.4
• /
• pp.291-295
• /
• 2004

Heat regenerator attached in small-scale regenerative radiant tube burner was designed using the theoretical computation code and was confirmed the performance of waste heat recovery ratio. From the computation, when ceramic ball of 4-5kg was used, temperature efficiency and available waste heat recovery ratio were predicted 80% and 70%, respectively. Similar efficiencies were obtained from the experiments using LPG. However, since exhaust gas temperature entered into regenerator was below 850$^{\circ}C$ which was moth lower than that we expected. air preheating temperature was lowered below 800$^{\circ}C$.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2002.12a
• /
• pp.166-169
• /
• 2002

본 논문에서는 사출성형기의 배럴의 정밀 온도제어에 대해 논의하였다 현재 사출성형기의 온도제어는 온도 편차가 2도 내외이며, 예열후 안정화되는데 걸리는 시간이 길다는 단점이 있다. 향후 마이크로-나노 시스템 제작 공정에 있어서 대량생산 방법으로 사출성형이 주목받을 것으로 기대된다. 특히 온도 제어의 경우는 사출시 인가해야 할 온도가 녹는점 및 glassy 온도에서 유지가 되면서 충분히 유동을 가지는 온도를 지속적으로 유지를 해야하므로 사출 후 정밀성에 중요한 요소가 된다. 마이크로-나노 사출공정은 극 미세 사출이며 온도, 압력에 따른 재료 특성 변화가 발생할 수 있으므로 이를 최적의 조건으로 제어할 수 있어야 한다. 본 연구에서는 실제 사출성형기와 PC based PLC를 이용한 온도제어기를 구현하고 실험하였다. 이를 통해 기존의 온도제어의 단점을 줄이고, 제어성능을 극대화하여 향후 마이크로-나노 시스템에 적용 가능한 정밀 온도제어기를 제안한다.

• Proceedings of the KWS Conference
• /
• 1996.05a
• /
• pp.176-178
• /
• 1996

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.180-181
• /
• 2005

• Journal of Ocean Engineering and Technology
• /
• v.29 no.6
• /
• pp.481-487
• /
• 2015

The effects of the heat input and preheat/interpass temperatures on the tensile strength and impact toughness of multipass welded weld metal were investigated and interpreted in terms of the recovery of the alloying elements and microstructure. Increases in both the heat input and preheat/interpass temperatures decreased the tensile strength of the weld metal. A lower recovery of alloying elements, especially Mn and Si, and smaller area fraction of acicular ferrite in the weld metal were observed in higher heat input welding, resulting in a lower tensile strength. In contrast, only a microstructure difference was observed at a higher preheat/interpass temperature. The impact toughness of the weld metal gradually increased with an increase in the heat input because of the lower tensile strength. However, it decreased again when the heat input was larger than 45 kJ/cm because of the much smaller area fraction of acicular ferrite. No effect of the preheat/interpass temperature on the impact toughness was observed. The formation of a weld metal heat-affect zone showed little effect on the impact toughness of the weld metal in this experiment.

• Journal of Welding and Joining
• /
• v.16 no.6
• /
• pp.77-85
• /
• 1998

Effects of non-cleaning and cleaning fluxes on the wetting properties and defects at flow soldered joints were investigated. Non-cleaning flux (R-type of 3.3% solid content) and cleaning flux (RMA-type of 15% solid content) were used. Wetting test was accomplished by wetting balance method with changing surface state of wetting specimen, CU. Sn-37%Pb solder was used for wetting test and flow soldering. As experimental results, the wetting time for vertical force from the surface tension being zero was mainly affected by surface state of the wetting specimen. Non-cleaning flux had a good wettability compared with cleaning flux. In case of non-cleaning flux, conveyor speed had a great affection to defects of bridge, icicle, and poor solder.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.2
• /
• pp.14-20
• /
• 2003

In this paper, a practical design criteria for judgement of crack occurrence in weldments is presented as a function of typical welding parameters, such as diffusible hydrogen, restraint intensity, and preheating temperature. The elastic analyses using the finite element techniques are employed in order to quantify the restraint intensities, numerically. Systematic experiments are also conducted in order to investigate the propensity of crack to typical welding parameters. The results of numerical estimation using the proposed method for the experimental specimens show the usefulness as a practical tool in welding induced crack problems with extensive uncertainties. Systematic experiments are also conducted in order to investigate the propensity of crack to typical welding parameters. The results of numerical estimation using the proposed method for the experimental specimens show the usefulness as a practical tool in welding induced crack problems with extensive uncertainties.