• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.59-59
• /
• 2017

무인 헬리콥터의 양력을 개선하기 위한 익형 설계 단계로서 두꺼운 익형(V1505A)과 얇고 처진 익형(V2008B)의 기본 두 익형의 특성을 예측하는데 있어 회전하는 블레이드의 현실적 조건을 반영한 3D 모델을 마련하고 성능을 예측하였다. Fluent를 이용한 400 mm 선형모델의 시뮬레이션에서는 V1505A 익형은 높은 받음각에서 안정적인 특성을 보인 반면 V2008B는 비교적 높은 동력효율 특성을 보였으나, 높은 받음각에서는 실속 이후 양력이 급락하는 특성을 나타낸다. 형성된 노드 수는 약 870,000개로 하였다. 시위길이 135 mm인 익형 V2008B의 형상은 ANSYS (Fluent v16.2)를 이용해 반경(길이) 1,502 (1,380) mm 의 로터 블레이드를 구성하였다. 충분하지 않은 유동장이 익형 표면에서의 유동의 영향에 영향을 주지 않도록 직경 20 m의 원방경계(far field)를 형성하였다. 사용된 매쉬의 형태는 정사면체 형태로 로터 표면으로부터의 첫 번째 두께 높이는 0.001 m이고 10개의 층으로 형성하였다. 정지 비행하는 헬리콥터의 상태를 가정하여 회전좌표계를 이용하여 정상상태의 유동을 해석하고 사용된 난류모델은 넓은 영역에서의 유동을 고려하여 Realizable $k-{\varepsilon}$ 모델을 사용하였다. 내측그립 받음각 $6{\sim}22^{\circ}$에 대하여 현실적인 회전속도를 연동하여 600~1000 rpm을 적용하였다. 반복수(iteration)는 2000으로 하여 잔차값(residual)이 충분히 수렴하도록 하였다. 전체적으로 실제 헬리콥터가 발휘하는 양력보다는 낮은 수치로 예측되었으며 모델 및 해석 조건에 대한 검토가 필요해 보인다. 양력 값은 받음각 $10^{\circ}$에서 자중(약 68 kgf)을 극복하였고 받음각 $12^{\circ}$에 유상하중 20 kgf을 발휘하며 888 N의 양력을 보였다, 이어 받음각 $22^{\circ}$에서 실속 현상이 발생하였다. 받음각이 증가함에 따라 항력 역시 증가하였으며 받음각 $12^{\circ}$에서 121 N이었고 실속에 이르며 항력은 갑자기 증가할 것으로 예측된다. 본 연구는 변이 익형 개발의 선행 단계로 기본 익형에 대한 공력특성을 CFD 시뮬레이션을 통하여 예측하였다. 예측 값은 현실적 실험방법을 통하여 검증이 되어야 하며 이후 변이익형에 대한 예측과 설계가 가능하다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.8
• /
• pp.611-620
• /
• 2018

For the past decades, the analytic model for distributed surface roughness has been developed to improve the accuracy of the icing simulation code. However, it remains limitations to validate the developed model and determine the empirical parameters due to the absence of the quantitative experimental data which were focused on the surface state. To this end, the experimental study conducted to analyze the ice covered surface state from a micro-perspective. Above all, the tendency of the smooth zone width which occurs near the stagnation point has been quantitatively analyzed. It is observed that the smooth zone width is increased as growing the ambient temperature and freestream velocity. Next, the characteristics of the ice covered surface under rime and glaze ice have been analyzed. For rime ice conditions, ice elements are developed as the opaque circular corn in the opposite direction of freestream. The height and interval of each circular corn are increased as rising the ambient temperature. For glaze ice conditions, numerous lumps of translucent ice can be observed. This is because the beads formed by gravity concentrate and froze on the lower surface.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.3
• /
• pp.578-584
• /
• 2017

$SiO_2$ buffer layer (100 nm) has been deposited on PET substrate by electron beam evaporation. And then, IZTO (In-Zn-Sn-O) thin film has been deposited on $SiO_2$/PET substrate with different RF power of 30 to 60 W, working pressure, 1 to 7 mTorr, by RF magnetron sputtering. Structural, electrical and optical properties of IZTO thin film have been analyzed with various RF powers and working pressures. IZTO thin film deposited on the process condition of 50 W and 3 mTorr exhibited the best characteristics, where figure of merit was $4.53{\times}10^{-3}{\Omega}^{-1}$, resistivity, $4.42{\times}10^{-4}{\Omega}-cm$, sheet resistance, $27.63{\Omega}/sq.$, average transmittance (400-800 nm), 81.24%. As a result of AFM, all the IZTO thin film has no defects such as pinhole and crack, and RMS surface roughness was 1.147 nm. Due to these characteristics, IZTO thin film deposited on $SiO_2$/PET structure was found to be a very compatible material that can be applied to the next generation flexible display device.

• Cartoon and Animation Studies
• /
• s.43
• /
• pp.185-209
• /
• 2016

Pattern refers to singular or repetitive decorative form in a blank surface, Also pattern is not just something to simply fill in the blanks, and has more meanings. Pattern reflects the specific culture or regional feature. So Depending on which pattern to use, creator can give particular of identity. which is generally utilized in visual arts such as painting, architecture, craft, as well as animation. Pattern in animation plays a role of decorating background or surfaces of characters' outfits or props. And Parttern is effective way to describe the story of the times and space environment of the background. Tomm Moore, an animation director in in Ireland mainly produces animations based on traditional folk stories or myths. He usually utilizes cultural and artistic factors related to the themes in his work production. One example is the insertion of pattern closely associated with the narratives and backgrounds of animations to create profound scenes. Tomm Moore used the Irish Celt pattern in Secret of Kells (2009) and Song of Sea (2014) and Islam geometric pattern and plant pattern in a short nimation named On Love from Kahlil Gibran's The Prophe (2014). This study attempts to examine the historical and cultural foundation and the narratives of these two animations, Song of Sea(2014) and Kahlil Gibran's The Prophet: On Love (2014) in which Tomm Moore participated as the director and producer, exploring their relevant traditional patterns. Moreover, it also attempts to analyze how these traditional patterns are utilized in the animations.

• The Journal of the Acoustical Society of Korea
• /
• v.33 no.3
• /
• pp.191-199
• /
• 2014

Wave reflection and transmission characteristics in waveguides are an important issue in many engineering applications. A combined spectral element and finite element (SE/FE) method is used to investigate the effects of local non-uniformities but limited at relatively low frequencies because the SE is formulated by using a beam theory. For higher frequency applications, a method named a combined spectral super element and finite element (SSE/FE) method was presented recently, replacing spectral elements with spectral super elements. This SSE/FE approach requires a long computing time due to the coupling of SSE and FE matrices. If a local non-uniformity has a uniform cross-section along its short length, the FE part could be further replaced by SSE, which improves performance of the combined SSE/FE method in terms of the modeling effort and computing time. In this paper SSEs are combined to investigate the characteristics of waves propagating along waveguides possessing geometric non-uniformities. Two models are regarded: a rail with a local defect and a periodically ribbed plate. In the case of the rail example, firstly, the results predicted by a combined SSE/FE method are compared with those from the combined SSEs in order to justify that the combined SSEs work properly. Then the SSEs are applied to a ribbed plate which has periodically repeated non-uniformities along its length. For the ribbed plate, the propagation characteristics are investigated in terms of the propagation constant.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.5
• /
• pp.1213-1218
• /
• 2013

In this study, Ga-doped ZnO (GZO) thin films were fabricated on transparent sapphire substrate by RF magnetron sputtering method and then investigated the effect of various substrate temperature on the electrical, optical properties and characteristic of crystallization of the GZO thin films. The electrical property indicated that the lowest resistivity ($4.18{\times}10^{-4}{\Omega}cm$), the highest carrier concentration ($6.77{\times}10^{20}cm^{-3}$) and Hall mobility ($22cm^2/Vs$) were obtained in the GZO thin film fabricated at $300^{\circ}C$. And for this condition, the highest c-axis orientation and (002) diffraction peak which exhibits a FWHM of $0.34^{\circ}$ were obtained. From the results of AFM measurements, it is known that the highest crystallinity is observed at $300^{\circ}C$. The transmittance spectrum in the visible range was approximately 80 % regardless of substrate temperature. The optical band-gap showed the blue-shift as increasing the substrate temperature to $300^{\circ}C$, and they are all larger than the band gap of bulk ZnO (3.3 eV). It can be explained by the Burstein-Moss effect.

• Journal of Korea Technology Innovation Society
• /
• v.22 no.3
• /
• pp.362-381
• /
• 2019

The purpose of this study is to examine how two factors among various affecting factors of technological innovation, i.e. sectoral system of innovation and R&D support service, were actually applied in the case of NUC Electronics. This company has achieved high level of innovation performance through change of injection port and improvement of extracting rate. This was possible because each component of sectoral system of innovation system was matched with the innovation activity. The improvement of the performance in NUC Electronics was attributable to its own innovation efforts and R&D support service of government research institute. In the process of technological innovation, the company could receive high-level services in areas such as product design and virtual experiments that companies can not solve themselves. It can be said that the role of government and public institutions to support the shortage of SMEs was important. In terms of each component of sectoral system of innovation, we found that there were many opportunities of new technology; sustainability was low; imitation was easy; appropriability was low but it has dualily; accumulation of technology was relatively high, availability of external knowledge was high. At the same time, both of the company and the network played an important role, and market conditions were very favorable. In terms of R&D support services, it is a direct effect that a great deal of time and cost savings have been achieved through virtual experiments on the material and shape of the screw. As an indirect effect, the core competence of the company has been greatly strengthened by utilizing the momentum of technology development through external support, hence the company could establish the structure of virtuous circle of innovation.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06b
• /
• pp.219-222
• /
• 1996

수열법은 밀폐용기중에서 10$0^{\circ}C$이상의 가열, 가압된 수용액이 반응에 관여하는 것으로써, 수정, CaCO3, AlPO4, GaPO4 등과 같은 단결정의 육성 뿐만 아니라 균일분산계로부터 균일한 결정성의 미립자 합성에도 폭넓게 이용되고 있다. 세라믹분말의 합성에 있어서, 이 방법은 특히 형상, 입자크기의 제어가 용이할 뿐만 아니라 고상법, 졸-겔법, 공침법에서와 같은 열처리, 분쇄과정이 필요없기 때문에 고순도의 초미립자를 얻을 수 있는 장점이 있다. 근년 미국, 일본에서는 수열법을 이용한 유전, 압전체 등 세라믹분말의 일부가 공업적인 규모로 대량 생산되고 있다. 그러나 이에 대한 국내 기술은 아직 초기단계에 이르고 있는 실정이다. 따라서 본 연구실에서는 수열법에 의한 단결정 육성 (예; 자수정, CaCO3, AlPO4, GaPO4, KTP, Emerald 등), 박막제조 (예; GaP, PbTiO3, BaTiO3 등), 정제 (고령토, 장석, 도석 등), 원석처리 (진주, 인공 emerald, 비취 등) 그리고 각종 세라믹분말의 합성 등과 같은 다양한 기반기술의 축적과 동시에 공업화에 대응한 수열장치를 위하여 반응용기의 대형화, 엄밀한 밀폐방식, 실용적인 수열조건 등을 개발해 오고 있다. 본 발표에서는 현재까지의 연구개발 내용 중에서 결정성 미립자에 관련한 세라믹분말의 합성에 대한 일부의 결과들을 보고한다. 일반적으로 수열장치는 전기로, 반응용기, 온도 및 압력제어계 등을 기본으로 하고 있으며 시판용의 대부분이 교반기가 부착된 수직형 (vertical type)이다. 이와 같은 방식에 있어서는 엄밀한 밀폐가 곤란, 반응온도의 한계성 (25$0^{\circ}C$ 이하), 증진율의 한계성 (소량생산) 등과 같은 점이 있기 때문에 본 연구실에서는 개폐식 전기로내에 엄밀한 밀폐가 가능한 수평식(horizontal type)의 반응용기를 채택한 뒤 이를 회전 또는 시이소(seesaw)식으로 움직일 수 있도록 하여 연속공정화, 온도구배의 자율조절 그리고 보다 저온에서도 인위적인 이온의 확산을 효율적으로 유도할 수 있도록 하였다. 이와 같은 방식은 기존의 방식과 비교하여 반응용기 내에 응집현상과 미반응물이 존재하지 않으며 또한 단분산으로 결정성 미립자를 대량적으로 얻을 수 있는 장점이 있었다. 다음은 이상과 같이 본 연구실에서 자체 개발한 수열장치를 이용하여 PbTiO3, (Pb,La)TiO3Mn, BaTiO3, ZnSiO4:Mn, CaWO4 등과 같은 세라믹분말에 대한 합성 실험의 결과이다. 압전성, 초전성이 우수한 PbTiO3 및 (Pb,La)TiO3:Mn 분말의 수열합성은 PbO, TiO2, La2O3 등의 분말을 출발원료로 하여 합성도도 25$0^{\circ}C$부근의 알카리성 용액중에서 결정성 PbTiO3 및 (Pb,La)TiO3:Mn 미립자를 단상으로 얻었으며 입자의 형상 및 크기는 합성온도와 수열용매의 종류에 의존하였다. 유전체로서 폭넓게 응용되고 있는 BaTiO3 분말은 Ba(OH)2.8H2O, TiO2와 같은 최적의 출발원료를 선택함으로써 15$0^{\circ}C$ 부근의 저온영역에서도 용이하게 합성할 수 있었다. 특히 본 연구에서는 수용성인 Ba(OH)2.8H2O를 사용함으로써 host-guest적인 반응을 유도시키는데 있어 물의 가장 실용적이고 효과적인 수열용매임도 알았다. ZnSiO4:Mn, CaWO4, MgWO4와 같은 형광체 분말은 공업적으로 고상반응 또는 습식법에 의해 얻어지고 있으나 이들 방법에 있어서는 분쇄공정으로 인한 형광특성의 저하와 같은 문제점이 있다. 따라서 본 연구에서는 수열법을 이용하여 이들 화합물의 합성을 시도하였으며 그 결과 합성온도 30$0^{\circ}C$ 부근의 알칼리성 용액중에서 수열적으로 얻어짐을 알았다. 여기서의 합성분말을 이용하여 실제 조명램프로 제조한 결과 녹색, 청색 발광용 형광체로서 우수한 형광특성을 나타내었다. 천연에서 소량 산출되고 있는 고가의 (Li,Al)MnO2(OH)2:Co 분말은 도자기의 전사지용 청색안료로써 이용되고 있다. 본 연구실에서는 LiOH.H2O, Al(OH)3, MnO2 등의 분말을 출발원료로 하고 24$0^{\circ}C$ 온도 부근 그리고 물을 수열용매로 하여 천연산에 필적하는 (Li,Al)MnO2(OH)2:Co 분말을 인공적으로 합성하였다.

• The Journal of Engineering Geology
• /
• v.15 no.3
• /
• pp.257-268
• /
• 2005

In situ rock mass is generally heterogeneous and discontinuous, with varying degrees of strength along the planes of weakness. The planes of weakness such as joints, faults, cracks and bedding planes, control the strength and deformation characteristics of the rock mass. Subsequently, the stability of underground opening depends upon the spatial distribution of discontinuities and their mechanical properties in relation with geometrical shape of openins as well as the mechanical properties of intact rock materials. Understanding the behaviour of a discontinuous rock mass remains a key issue for improving excavation design in hiかy stressed environments. Although recent advances in rock mechanics have provided guidelines for the design of underground opening in isotropic rock mass, prediction and control of deformation in discontinuous rock masses are still unclear. In this study, parametric study was performed to investigate the plastic zone size, stress distribution and deformation behavior around underground opening in a discontinuous rock mass using a continuum joint model. The solutions were obtained by an elasto-plastic finite difference analysis, employing the Mohr-Coulomb failure criteria. Non-associated flow rule and perfectly plastic material behavior are also assumed.

• The Korean Journal of Rheology
• /
• v.10 no.4
• /
• pp.217-226
• /
• 1998

The anisotropy caused by the fiber orientation, which is inevitably generated by the flow during injection molding of short fiber reinforced polymers, greatly influences dimensional accuracy, mechanical properties, and other quality of the final product. Since the filling stage of the injection molding process plays a vital role in determining fiber orientation, an accurate analysis of flow field for the filling stage is needed. Unbalanced filling occurs when a complex or a multi-cavity mold is used leading to development of regions where the fiber suspension is under compression. It is impossible to make an accurate calculation of the flow field during filling with the analysis assuming incompressible fluid. A mold with four cavities with different filling times was produced to compare the numerical analysis results with the experimental data. There was a good agreement between the experimental and theoretical results when the compressibility of the polymer melt was considered for the numerical simulation. The fiber orientation states for compressible and incompressible fluids were also compared qualitatively as well as quantitatively in this study.