• Journal of the Korea Concrete Institute
• /
• v.25 no.6
• /
• pp.613-620
• /
• 2013

Concrete has been recognized as a material which is resistant to high temperatures, but chemicophysical property of concrete is changed by the high temperature. So, mechanical properties of concrete may be reduced. Because of this, standards and researches on the degradation of the mechanical properties of concrete at high temperatures have been presented. However, research data about the state that considering the loading condition and high-strength concrete is not much. Therefore, this study evaluated the high-temperature properties of high-strength concrete by loading condition and elevated temperature. The stress-strain, strain at peak stress, compressive strength, elastic modulus, thermal strain and the transient creep are evaluated under the non-loading and $0.25f_{cu}$ loading conditions on high strength concrete of W/B 12.5%, 14.5% and 20%. Result of the experiment, decrease in compressive strength due to high temperature becomes larger as the compressive strength increases, and residual rate of elastic modulus and compressive strength is high by the shrinkage caused by loading and thermal expansion due to high temperature are offset from each other, at a temperature above $500^{\circ}C$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.285-288
• /
• 2007

박막형 태양전지 및 플렉서블 태양전지 기판으로 사용되는 금속기판의 우수성은 잘 알려져 있다. 그러나 상용 금속기판이 직면하고 있는 문제점을 보완하기 위해서 전주법으로 제조된 2원합금 금속포일을 개발하였으며, 박막형 및 플렉서블 태양전지의 기판재로 적용가능성을 확인하였다. 일반적으로 태양전지를 제조할 때 열 공정이 수행되며, 이때 기판재와 cell을 구성하는 반도체의 열팽창 계수 차이에 의한 열변형으로 결함이 발생될 수 있고, 태양전지 효율 및 수명을 저하시키는 원인이 될 수 있다. 이러한 원인이 될 수 있는 구성 재료간의 열팽창계수 차이에 의한 cell 의 변형량을 추정하기 위해 유한요소해석 방법을 사용하였다. 유한요소해석을 수행하기 위해 ALGOR 라는 해석 tool 을 사용하였다. 유한요소해석 수행에 사용된 상용 금속인 Mo, Ti, Al, SUS 포일과 전주법으로 제조된 2원합금 금속포일의 열팽창 계수는 실험을 통한 측정치이며, cell을 구성하는 반도체의 열팽창 계수와 열특성은 참고 문헌에 있는 자료들이다. 이 값들을 기반으로 cell 의 구성을 단순화시킨 가상의 태양전지가 제조 공정 온도에서 상온으로 냉각될 때의 열변형량을 계산하였다.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.116-119
• /
• 2000

본 연구에서는 온도의 상승에 의하여 부피가 팽창하는 열팽창 고무 치공구의 팽창 특성을 이용하여 열경화성 복합재료를 경화하고 압축하는 과정을 실험과 모델링을 통하여 해석하였으며, 열가소성 복합재료의 함침공정을 연구하였다. 열팽창 고무치공구가 사용되는 닫힌계와 열린계에서 예상되는 압력을 이론적으로 유도하였고, 경화가 수반되는 과정에 있어서는 실험을 통하여 열팽창치공구와 프리프레그가 나타내는 압력을 측정하였다. 온도가 상승하고 경화가 수반되는 경우에 등속도 압축실험에 의하여 얻어지는 응력-변형율 곡선은 비선형점탄성 특성을 보여주었는데, 본 연구에서는 Maxwell모델을 KWW(Kohlrausch-Williame-Watts)식으로 변형시킨 모델식을 이용하여 이를 매우 정확하게 표현할 수 있었다. 또한 고무치공구를 이용하여 열가소성 수지의 복합재료 성형공정을 실험하였고, 중성자 레디오그래피 촬영을 통하여 기공의 분포를 관찰하였다.

• Journal of the Korea Concrete Institute
• /
• v.23 no.5
• /
• pp.627-636
• /
• 2011

Recently, to prevent explosive spalling of high-strength concrete (HSC) members, the usage of nylon fiber instead of polypropylene fiber has increased. Past experimental studies have been conducted to examine the spalling and mechanical properties of HSC with nylon fibers when exposed to elevated temperature. However, the previous studies on HSC with nylon fibers subjected to high temperatures were performed only on the properties such as spalling, compressive strength, and elastic modulus rather than investigations on to the behaviors such as thermal strain, total strain, steady state creep, and transient creep. Therefore, in this study thermal strain, total strain, steady state creep, and transient creep of HSC mixed with nylon fibers with water to binder ratio of 0.30 to 0.15 were tested. The experimental results showed that nylon fibers did not affect the performance of HSC with nylon fibers at high temperatures. However, HSC with nylon fibers generated a larger transient creep strain than that of HSC without fibers and normal strength concrete.

• Composites Research
• /
• v.16 no.1
• /
• pp.1-12
• /
• 2003

This study developed SiC$_{p}$/A1$_2$O$_3$$_{f}$/Al composites for electronic packaging to which reinforcements were added with the volume fractions of 49%, 56% and 63% by the squeeze casting method. 0.8 wt. % of the inorganic binder as well as the A1$_2$O$_3$ fiber and SiC Particles with the volume fraction of 1:10 were added to the composites, which were produced in the newly designed mold. For the produced SiC/Al composites, the CTEs (coefficients of thermal expansion) were measured from 30 to 300 and compared with the FEM numerical simulation to analyze the temperature dependent properties. The experiment showed the CTEs of SiC$_{p}$/A1$_2$O$_3$$_{f}$/Al composites that were intermediate values of those of Rule of Mixture and Turner's Model. The CTEs were close to Turner's Model in the room temperature and approached the Rule of Mixture as the temperature increases. These properties analyzed from the difference of the average stress acting between the matrix and the reinforcements proposed in this study.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.49-49
• /
• 2004

고도화로 정밀해진 현대 과학기기에는 여러 가지 전자 팩키징 제품들이 쓰이고 있으나 이 제품들은 여러 가지 파손인자들의 영향 때문에 고유의 수명을 다하지 못하고 고장이 발생하게 된다. 전자부품 실장에 이용되는 솔더 조인트의 열화에 관련되는 열 피로와 이온 마이그레이션(Migration) 현상이 솔더 조인트의 신뢰성에 영향을 미치는 가장 중요한 인자로 알려져 있고 이러한 인자 이외에도 여러 가지 요인들이 복합적으로 작용하여 솔더의 접합부분에 피로파괴를 일으킨다.(중략)

• Journal of the Korea Concrete Institute
• /
• v.23 no.6
• /
• pp.723-730
• /
• 2011

It is very important to experimentally evaluate concrete behavior at elevated temperature because aggregates make up approximately 80 percent of volume in concrete. In this study, an experiment to evaluate mechanical properties of normal weight and light weight concrete of 60 MPa was conducted. Based on loading level of 0, 20 and 40 percent, the tests of 28 days compressive strength, elastic modulus, thermal strain, total strain, and transient creep using ${\phi}100{\times}200mm$ cylindrical specimens at elevated temperature were performed. Then, the results were compared with CEB (Committes Euro-international du Beton) model code. The results showed that thermal strain of light weight concrete was smaller than normal weight concrete. Also, the results showed that compressive strength of light concrete at $700^{\circ}C$ was higher than normal weight concrete and CEB code, similar to that obtained at ambient temperature. Transient creep developed from loading at a critical temperature of $500^{\circ}C$ caused the concrete strains to change from expansion to compression. The transient creep test result showed that internal force was high when the ratio of shrinkage between concrete and aggregate was more influential than thermal expansion.

• Journal of the Korea Concrete Institute
• /
• v.13 no.3
• /
• pp.228-236
• /
• 2001

Even though numerous researches have been performed for the prediction of thermal stresses in mass concrete structures by both analytical and experimental means, the limitations exist for both approaches. In analytical approach, the fundamental limitation is derived from the difficulty of predicting concrete properties such as modulus of elasticity, coefficient of thermal expansion, etc.. In experimental approach, there are many uncertainties related to in-situ conditions, because a majority of researches have focused on measuring thermal stresses in actual and simulated structures. In this research, an experimental device measuring thermal stresses directly in a laboratory setting is developed. The equipment is located in a temperature chamber that follows the temperature history previously obtained from temperature distribution analysis. Thermal strains are measured continuously by a strain gauge in the device and the corresponding thermal stresses are calculated simply by force equilibrium condition. For the verification of the developed device, a traditional experiment measuring thermal strains from embedded strain gauges is performed simultaneously. The results show that the thermal strain values measured by the newly developed device agree well with the results from the benchmark experiment.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.1
• /
• pp.58-66
• /
• 2022

In this study, to examine the effect of the transverse thermal expansion behavior of FRP reinforcing bars and concrete on the concrete cover thickness, based on 20℃, when the temperature changes from -70℃ to 80℃, the behavior of concrete was studied theoretically and numerically. Theoretical elastic analysis and nonlinear finite element analysis were performed on FRP reinforced concrete with different diameters and cover thicknesses of FRP reinforcement. As a result, at a negative temperature difference, concrete was compressed, and the theoretical strain result and the finite element result were similar, but at a positive temperature difference, tensile stress and further cracks occurred in the concrete, which was 1.2 to 1.4 times larger than the theoretical result. The ratio of the diameter of the FRP reinforcing bar to the thickness of the concrete cover (c/db) is closely related to the occurrence of cracks. Since the transverse thermal expansion coefficient of FRP reinforcing bars is three times greater than that of concrete, it is necessary to consider this in design.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.11 no.1
• /
• pp.1-6
• /
• 1999

Nearshore and offshore pipelines are often applied to carry oil, gas, water and combined products. The thermal and pressure gradients of the fluid inside pipeline cause pipeline expansion. This expansion produces stress to connecting structures with pipeline. Should this stress exceeds the yield strength of connecting components or the allowable displacement of the system, a damage can occur. As most pipelines contain hazardous and toxic fluids, the damage usually leads to fatal accidents involving great economic loss as well. Even subsea pipelines can be easily applied to transport liquid type fluid without time and space constraint, they should be designed and maintained carefully to be functional safely during design lifetime. In this paper, various theories estimating pipeline thermal expansion are investigated and the effects of pipe components to expansion are studied.