• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.568-573
• /
• 2008

Kinetic tests on pyrolysis of waste fishing net [WFN; nylon-6], waste ship lubricating oil [WSLO] and their mixture were carried out by thermogravimetric analysis (TGA) with heating rate of 0.5, 1.0, and $2.0^{\circ}C/min$. Pyrolysis of waste fishing net started at $300^{\circ}C$, and the main region of decomposition temperature was between 360 and $440^{\circ}C$ at each heating rate. Decomposition temperature of the mixture of WFN and WSLO was lower than that of WFN and WSLO, and the shape of thermogravimetic graph of mixture was different as well. The corresponding kinetic parameters including activation energy and pre-exponential factor were determined by differential method over the degree of conversions. The values of activation energies for the mixture of WFN and WSLO were between 98 and 427 kJ/mol as the conversion increased from 5% to 95%. Tubing reactor was used to analysis of pyrolyzed oil at $440^{\circ}C$ for 80 min. The selectivity of specific hydrocarbons was not detected and the carbon number distribution of the pyrolyzed oil was below $C_{22}$.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.1
• /
• pp.65-70
• /
• 2010

The distillation rate on LiCl-KCl eutectic salt under different vacuums from 0.5-50 mmHg was first investigated by using both a non-isothermal and a isothermal thermogravimetric (TG) analysis. Based on the non-isothermal TG data, distillation rate equations as a function of the temperature could be derived. Calculated flux by these model flux equations was in agreement with the distillation rate obtained from isothermal TG analysis. A distillation rate of $10^{-4}-10^{-5}$ mole $cm^{-2}sec^{-1}$ is obtainable at temperatures less than 1300K and vacuums of 0.5-50 mmHg. About a 99% salt distillation efficiency was obtained after an hour at a temperature above 1150 K under 50 mmHg in a small scale distillation test system. An increase in the vaporizing surface area is relatively effective for removing residual salt in the remaining particles, when compared to that for the vaporizing time. Over 99.95% of total distillation efficiency was obtained for a 1-h distillation operation by increasing the inner surface area from $4.52cm^2$ to $12.56cm^2$.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.7
• /
• pp.531-540
• /
• 2009

In this study, thermo-gravimetric analysis(TGA) was used to investigate the effect of urea concentration and heating rate on the ammonia($NH_3$) formation process from urea solution. A newly designed pipe nozzle was inserted through a 1,000 N${\ss}$(C)/h oil firing boiler to compare the DeNOx efficiencies between the upward and downward nozzle. This experiment reveals the effect of path which an urea droplet goes through. Urea solution showed the same TGA graph without regard to the presence of oxygen. Heating rate had a great influence on the weight loss trend. But the concentration of urea solution between 10% and 40% did not affect so much the thermal decomposition temperature. Therefore, heating rate is more important factor on the thermal decomposition of urea than the concentration of urea solution. Three nozzles located at different positions showed similar DeNOx efficiencies such as 68.1%, 71.8%, 70.8% at the same temperature. Even though urea solution was injected for the same zone, the injection direction made much difference in DeNOx efficiency. A upward nozzle showed 68.1% and downward nozzle 9.5%. This results illustrate the importance of heating rate.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2012.04a
• /
• pp.26-29
• /
• 2012

본 연구에서는 목분-폴리프로필렌 복합재의 연소성 및 열적특성을 평가하기 위하여 한계산소지수 실험 및 열중량 분석실험을 실시하였다. 목분-폴리프로필렌 복합재의 제조를 위하여 이축압출기를 활용한 압출공정과 사출성형기를 활용한 사출공정을 이용하였다. 그리고 복합재의 난연성능 향상을 위하여 난연제(4종류)를 첨가한 복합체의 화재성능을 평가하였다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.1
• /
• pp.53-62
• /
• 2024

In this paper, an experimental study on the strengths and material properties of concrete manufactured by using coal gangue, as a fine aggregate was conducted. Experimental parameters included coal gangue aggregate contents as a replacement of fine aggregate by 50 % and 100 % (by volume) and fly ash contents. The water-binder ratio was fixed at 0.38. In addition, 30 % of the OPC binder was replaced with fly ash in some mixtures. Test of the unit weight, compressive, split tensile, and flexural tensile strength of concrete were performed and test results were analyzed. Unit weight, compressive strength, split tensile strength, and flexural tensile strength decreased as the coal recycled aggregates increased. In addition, TGA and SEM experiments, which are microstructure experiments, were conducted to analyze thermogravimetric analysis and ITZ by section.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.11
• /
• pp.727-734
• /
• 2017

The electrochemical conversion of $CO_2$ is one of the methods for reducing $CO_2$. Four materials (Ag, Ni, Pt, and Ir) were selected as the electrodes. The electrochemical conversion was performed under a cell voltage of 4.0 V at $600^{\circ}C$. The amounts of $CO_2$ reduction and carbon production were at the highest for Ag, followed by, Pt, Ni, and then Ir. The produced carbon samples were analyzed by thermogravimetric analysis and XRD. The thermogravimetric analysis results indicated that all the carbon produced at each electrode exhibited similar thermal reactivity. The XRD results showed that the crystallization of carbon was different depending on the electrode utilized. Although electrochemical conversion was the highest for the Ag electrode, a loss of material accompanied it. Therefore, for this study, the optimal electrode is Pt, taking into account reactivity and material losses.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.4
• /
• pp.1-8
• /
• 2012

The aim of this study is to evaluate fire-induced damage for shield tunnel linings. Full-scale fire test was conducted to evaluate fire-induced damage. Residual compressive strength was measured on the core samples of shield tunnel lining subjected to high temperatures. Heating temperature was predicted by XRD and TG analysis. As a result, Strength degradation of concrete with temperatures can be evaluated by residual compressive strength of core samples. In addition, residual compressive strength can be estimated by previous studies if heating temperature is exactly predicted. It is possible that heating temperature is predicted by XRD and TG analysis at $450^{\circ}C$. For more accurate prediction of heating temperature it should be performed both instrumental analysis and analytical methods with temperatures ranging from $400{\sim}600^{\circ}C$.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.8
• /
• pp.598-606
• /
• 2013

This study was performed to determine whether biomineralization microbes were actively present underneath landfill cover soil producing biocalcification. From this, various types of microbes were observed. Among them, two species were dominantly found; Bacillus megaterium and Alkaliphilus metalliredigens that were known as biominerlization bacteria. With those microbes, $CO_2$ was more highly consumed than without bacteria. In response, the calcium carbonate mineral was produced at 30% (wt) greater than that of the control. At the same time, TG-DTA was successfully used for quantification of $CO_2$ consumed forming calcium carbonate minerals resulting from biocalcification. It was decided that the presence of solidified sewage sludge cake utilized as a cover soil in the landfill could efficiently contribute to possible media adaptably and naturally sequestering $CO_2$ producing from the landfill.

• Korean Chemical Engineering Research
• /
• v.48 no.1
• /
• pp.58-67
• /
• 2010

Combustion of the Korean Anthracite and wood-pellet was characterized in air atmosphere with variation of heating rate(5, 10, 20 and $30^{\circ}C/min$) in TGA. The results of TGA have shown that the combustion of the wood-pellet occurred in the temperature range of $200{\sim}620^{\circ}C$ which is much lower than that of Korean anthracite. Activation energies of the wood-pellet and Korean anthracite, determined by using Friedman method were 44.12, 21.45 kcal/mol respectively. Also, their reaction orders(n) and pre-exponential factors(A) were 5.153, 0.7453 and $4.01{\times}10^{16}$, $1.39{\times}10^6(s^{-1})$ respectively. In order to find out the combustion mechanism of the wood-pellet and Korean anthracite, twelve solidstate mechanisms defined by Coats Redfern Method were tested. The solid state combustion mechanisms of the woodpellet and Korean anthracite were found to be sigmoidal curve A3 type and a deceleration curve F1 type respectively. Also, from iso-thermal combustion($300{\sim}900^{\circ}C$) of their char, the combustion characteristics of their char was found. Activation energies of the their char were 27.5, 51.2 kcal/mol respectively. Also, pre-exponential factors(A) were $2.55{\times}10^{12}$, $1.49{\times}10^{10}(s^{-1})$ respectively. Due to the high combustion reactivity of wood-pellet compared with Korean anthracite, combustion atmosphere will be improved by co-combustion with Korean anthracite and wood-pellet.

• Journal of the Korean Institute of Gas
• /
• v.17 no.5
• /
• pp.69-74
• /
• 2013

The study was conducted experimentally on characteristic of thermal decomposition and minimum ignition temperature of magnesium dusts. For this purpose, three different Mg dusts of mean diameter (38, 142, $567{\mu}m$) were used. Experimental investigations were conducted by using TGA(Thermo gravimetric analysis) and MIT(Minimum Ignition Temperature) apparatus made in accordance with IEC 61241-2-1 standard. As the results, temperature of weight gain in Mg dust layers increased with increasing of heating rates in air and, under the same heating rate condition, minimum ignition temperature increased with particle size. Also the MIT of suspended Mg dust clouds tended to increase with increasing of mean diameter.