• Restorative Dentistry and Endodontics
• /
• v.34 no.1
• /
• pp.42-50
• /
• 2009

Deterioration of long-term dentin adhesion durability is thought to occur by hydrolytic degradation within hydrophilic domains of the adhesive and hybrid layers. This study investigated the hypothesis that priming the collagen network with an organic solvent displace water without collapse and thereby obtain good bond strength with an adhesive made of hydrophobic monomers and organic solvents. Three experimental adhesives were prepared by dissolving two hydrophobic monomers, bisphenol-A-glycidylmethacrylate (Bis-GMA) and triethyleneglycol dimethacrylate (TEGDMA), into acetone, ethanol or methanol. After an etching and rinsing procedure, the adhesives were applied onto either wet dentin surfaces (wet bonding) or dentin surfaces primed with the same solvent (solvent-primed bonding). Microtensile bond strength (MTBS) was measured at 48 hrs, 1 month and after 10,000 times of thermocycles. The bonded interfaces were evaluated using a scanning electron microscope (SEM). Regardless of bonding protocols, well-developed hybrid layers were observed at the bonded interface in most specimens. The highest mean MTBS was observed in the adhesive containing ethanol at 48 hrs. With solvent-primed bonding, increased MTBS tendencies were seen with thermo cycling in the adhesives containing ethanol or methanol. However, in the case of wet bonding, no increase in MTBS was observed with aging.

• Clean Technology
• /
• v.24 no.3
• /
• pp.212-220
• /
• 2018

Oxy-fuel combustion is considered as a promising greenhouse gas reduction technology in power plant. In this study, the behaviors of NO and $SO_2$ were investigated under the condition that in-furnace $deNO_x$ and $deSO_x$ methods are applied in oxy-fuel circulating fluidized bed combustion condition. In addition, the generation trends of $SO_3$, $NH_3$ and $N_2O$ were observed. For the purpose, limestone and urea solution were directly injected into the circulating fluidized bed combustor. The in-furnace $deSO_x$ method using limestone could reduce the $SO_2$ concentration in exhaust gas from ~403 to ~41 ppm. At the same experimental condition, the $SO_3$ concentration in exhaust gas was also reduced from ~3.9 to ~1.4 ppm. This trend is mainly due to the reduction of $SO_2$. The $SO_2$ is the main source of the formation of $SO_3$. The negative effect of $CaCO_3$ in limestone, however, was also appeared that it promotes the NO generation. The NO concentration in exhaust gas reduced to ~26 - 34 ppm by appling selective non-catalytic reduction method using urea solution. The $NH_3$ concentration in exhaust gas was appeared up to ~1.8 ppm during injection of urea solution. At the same time, the $N_2O$ generation also increased with increase of urea solution injection. It seems that the HNCO generated from pyrolysis of urea converted into $N_2O$ in combustion atmosphere. From the results in this study, the generation of other pollutants should be checked as the in-furnace $deNO_x$ and $deSO_x$ methods are applied.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.11
• /
• pp.1132-1138
• /
• 2008

The study was carried out to investigate adsorption characteristic on hydrogen sulfide (H$_2$S) and methylmercaptan (CH$_3$SH) odor gas using the char made by a thermal decomposition of sewage sludge. The fixed bed adsorption experiments of the optimum L/D ratio could be 1.0, and adsorption capacity and break point increased with the increase of temperature. A simultaneous adsorption characteristic of H$_2$S and CH$_3$SH increased in breakthrough time and adsorption capacity more than single adsorption experiment, and CH$_3$SH had higher effective diffusivities than H$_2$S in same condition. The adsorption capacity of CH$_3$SH increased with fast velocity. When it was compared the produced absorbent with commercial activated carbon, As to adsorbent amount, it was H$_2$S 77% and CH$_3$SH 80% of commercial activated carbon.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2007.05a
• /
• pp.810-813
• /
• 2007

본 논문에서는 맥락 인식 (context-aware) 애플리케이션 개발에 있어서 사용자의 맥락 정보를 보다 효과적으로 처리할 수 있는 사용자 중심의 맥락 모델을 제안한다. 유비쿼터스 컴퓨팅 개념의 확산과 함께 맥락 인식 애플리케이션들에 관한 많은 연구가 진행되고 있다. 하지만, 맥락에 대한 정의는 여전히 모호하며, 애플리케이션들 마다 서로 다른 형태의 맥락을 활용하고 있기 때문에, 맥락에 대한 보다 구체적인 정의와 다양한 애플리케이션에 활용 가능한 형태의 맥락 모델이 필요하다. 제안된 사용자 중심의 맥락 모델에서는 사용자가 애플리케이션과 상호작용할 때 사용자의 직접적인 명령을 제외한 사용자와 관련된 정보를 맥락으로 정의한다. 또한, 제안된 사용자 중심의 맥락은 5W1H 형태로 구조화한 맥락요소 (ContextElement), 맥락 요소들을 편리하게 처리할 수 있는 연산자들을 포함하는 맥락 (Context), 그리고 단편적인 맥락 정보뿐만 아니라 기존의 맥락 정보까지도 활용할 수 있는 맥락메모리 (ContextMemory)로 구성된다. 특히, 다양한 센서들로부터 획득된 정보를 맥락 모델의 인터페이스를 통해서 맥락 인식 애플리케이션에서 활용할 수 있기 때문에, 서로 다른 맥락 인식 애플리케이션들을 개발함에 있어서도 동일한 맥락 모델을 사용할 수 있는 장점이 있다. 제안된 맥락 모델의 유용함을 보이기 위해서, 센서로부터 획득된 맥락 정보를 처리하는데 소요되는 시간을 측정하는 실험을 하였다. 따라서 제안된 사용자 중심의 맥락 모델은 사용자와 맥락 인식 애플리케이션간 자연스러운 상호작용을 지원할 것으로 기대된다.) kcal/mol의 생성활성화 에너지 감을 나타내었고, TGA로부터의 분해활성화 에너지는 각각 31.94, 30.84, 24.16 kcal/mol의 값을 나타내었다.로 감소되었다(35.2% vs. 77.4%; p<0.01). 실험 2에서 다양한 정자 농도에 의한 정자 침투율과 정상 수정률을 바탕으로 판단했을 때 $4.6{\times}10^6/ml$의 정자 농도가 다른 정자 농도에 비해 난구 세포부착 난자의 체외 수정에 적합한 것으로 나타났다. 체외 수정과정에서 난구 세포 부착된 상태로 수정된 난자는 나화 난자에 비해 유의적으로(p<0.05) 높은 분할률(48.8% vs. 58.9%), 배반포 형성률(11.0% vs. 22.8%)과 배반포 세포수$(22{\pm}2\;vs.\;29{\pm}2)$를 나타내었다. 본 연구의 결과로부터 돼지의 체외 수정과정에서 난구 세포의 존재는 정자 침투를 저해하지만 분할률, 배반포 형성률 및 배반포의 세포수를 증가시키는 것으로 사료된다.수의 유출입 지점에 온도센서를 부착하여 냉각수의 온도를 측정하고 냉각수의 공급량과 대기의 온도 등을 측정하여 대사열의 발생을 추정할 수 있었다. 동시에 이를 이용하여 유가배양시 기질을 공급하는 공정변수로 사용하였다 [8]. 생물학적인 폐수처리장치인 활성 슬러지법에서 미생물의 활성을 측정하는 방법은 아직 그다지 개발되어있지 않다. 본 연구에서는 슬러지의 주 구성원이 미생물인 점에 착안하여 침전시 슬러지층과 상등액의 온도차를 측정하여 대사열량의 발생량을 측정하고 슬러지의 활성을 측정할 수 있는 방법을 개발하였다.enin과

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.9
• /
• pp.971-978
• /
• 2012

Vacuum carburizing is supposed to be the superior process to the gas carburizing. However, the vacuum carburizing has the stage in which hydrocarbon gas is supplied into the furnace to be pyrolysis, and consequently the stable heat treatment is hard to achieve due to the soot from the hydrocarbon pyrolysis. Recently, many studies have been made which utilize acetylene gas to overcome this defects. In this paper, the carburizing and the diffusion periods have been selected based on the Harris experimental formula, and the mechanical properties of the vacuum carburized specimen have been compared with those of the gas carburized SCM415H specimen to identify the feasibility of the $CO_2$ free vacuum carburizing process. The result showed that the vacuum carburized materials used have no oxidization of the grain boundaries, and show the 29.8% higher effective hardness depth and the acceptable tensile strength.

• Economic and Environmental Geology
• /
• v.39 no.6 s.181
• /
• pp.753-770
• /
• 2006

In urban areas, groundwater pollution is heavily affected by urbanization with land use types. This study aims to characterize groundwater quality and contamination in Sasang industrial area of Busan Metropolitan City where metalworking, machinery and footwear factories are located. Busan Metropolitan City is the highest in the utilization of groundwater resources among the metropolitan cities in Korea. $K^+,\;Na^+,\;Ca^{2+},\;Mg^{2+},\;Cl^-,\;SO_4^{2-}\;and\;HCO_3^-$ concentrations, and electrical conductivity (EC), total dissolved solids (TDS) and salinity are high in the areas near the Nakdong River. The results are attributed to the influence of salt water which intruded into the coastal sediments during sedimentation. In addition, the dominant chemical type of Ca-Cl indicates the influence of salt water in the geological formations as well as anthropogenic pollution. $SiO_2$ ion is interpreted to originate from both water-silicate mineral reactions and the decomposition of cement concretes. Trichloroethylene (TCE) was detected at 12 sites of total 18 sites. However, tetrachloroethylene (PCE) was detected at f sites and 1.1.1-trichloroethane (TCA) at 3 sites. According to the factor analysis, factor 1 was explained by 49.8%, factor 2 19.8%, and factor 3 11.0% with total 80.6% explanation. pH, TDS, salinity, $Ca^{2+},\;K^+,\;Mg^{2+},\;Na^+,\;Al^{3+},\;As^{3+},\;Cl^-\;and\;Fe^{2+}$ were positively highly loaded to factor 1. The chemical components loaded to factor 1 represent the chemical characteristics of both industrial pollution and influence by salt water. Based on the cluster analysis and distribution pattern of chemical components, the concentration of $Na^+,\;Ca^{2+},\;Cl^-,\;SO_4^{2-}\;K^+,\;and\;Mg^{2+}$ is high in the riverside area of the Nakdong River composed of coastal sediments that is influenced by salt water. The downstream area of the Hakjang Stream is judged to be affected by both salt water and artificial pollution. The other part of the study area is interpreted by anthropogenic pollution.

• Korean journal of applied entomology
• /
• v.1
• /
• pp.20-25
• /
• 1962

A. The increases moisture contents of grain at R.H $75\%,\; and\; 28^{\circ}C$ 1) The moisture contents of polished rice were $0.4\%,\; 1 \%,\; 3.3\%$ higher than control after 4weeks in which had been infested with 100, 200, 500 individuals of weevil at the beginning. respectively. 2) The greatest moisture contents of polished rice was $16.26\%$ for 500 individual infested grain and the lowest one was $14.86\%$ for the 100 individual weevil infested grain after 4 weeks. 3) The increases in moisture contents of grain were proportionally greater with the size of the weevil population. B. Changes in moisture contents of polished rice at the three levels of cylinder which contain 3kgs of grain and 1000 weevils were infested at the beginning of the experiment. 1) The moisture contents of the grain at all the levels of the cylinder which was not infested with weevil, were consistantly decreased in 12 weeks. 2) The moisture contents of the grain at all the levels of the cylenders which had been infested with 1000 weevils at the beginning of the experiment, were increased except top lovel, that were $15.6\%$ for middle, $41.55\%$ for the bottom levels after 12 weeks. 3) The moisture contents of the grain were greater toward bottom in both weevil infested grain and in control. 4) The moisture content increase might be caused by the respiration of the weevils and deterioration of the grain by microorganisms. 5) There were no tendency to confine the weevils at any definite levels, but as the deterioration of the grain goes on, the weevil moved to top levels of cylinders. 5) The decreases in moisture contents of the grain at the top levels of the cylinders might be caused by diffusion of water to the environment. 7) The differences in temperature at three levels of the cylinder from enviroment were little or negative in control but were greater and positive. and the bottom were higher than top in experimental cylinders. 8) The increases of temperature might be caused by the respiration of the weevil and microorganisms.

• Journal of the Mineralogical Society of Korea
• /
• v.25 no.4
• /
• pp.185-195
• /
• 2012

Due to the high reduction and sorption capacity as well as the large specific surface area, nanosized mackinawite (FeS) is useful in reductively transforming chlorinated organic pollutants and sequestering toxic metals and metalloids. Due to the dynamic nature in its colloid stability, however, nanosized FeS may be washed out with the groundwater flow or result in aquifer clogging via particle aggregation. Thus, these nanoparticles should be modified such as to be built into permeable reactive barriers. This study employed coating methods in efforts to facilitate the installation of permeable reactive barriers of nanosized mackinawite. In applying the methods, nanosized mackinawite was coated on non-treated silica sand (NTS) and chemically treated silica sand (CTS). For both silica sands, the maximum coating of mackinawite occurred around pH 5.4, the condition of which was governed by (1) the solubility of mackinawite and (2) the surface charge of both silica and mackinawite. Under this pH condition, the maximum coating by NTS and CTS were found to be 0.101 mmol FeS/g and 0.043 mmol FeS/g respectively, with such elevated coatings by NTS likely linked with impurities (e.g., iron oxides) on its surface. Arsenite sorption experiments were performed under anoxic conditions using uncoated silica sands and those coated with mackinawite at the optimal pH to compare their reactivity. At pH 7, the relative sorption efficiency between uncoated NTS and coated NTS changed with the initial concentration of arsenite. At the lower initial concentration, uncoated NTS showed the higher sorption efficiency, whereas at the higher concentration, coated NTS exhibited the higher sorption efficiency. This could be attributed to different sorption mechanisms as a function of arsenite concentration: the surface complexation of arsenite with the iron oxide impurity on silica sand at the low concentration and the precipitation as arsenic sulfides by reaction with mackinawite coating at the high concentration. Compared to coated NTS, coated CTS showed the lower arsenite removal at pH 7 due to its relatively lower mackinawite coating. Taken together, our results indicate that NTS is a more effective material than CTS for the coating of nanosized mackinawite.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.4
• /
• pp.733-742
• /
• 2000

Fundamental materialistic characterization and adsorption/neutralization behavior of waste egg shell for heavy metal ion have been studied for its application to wastewater treatment. To investigate the structural change and thermal decomposition characteristics of egg shell. X-ray diffraction and FT-IR analysis were conducted for egg shell treated at $105^{\circ}C$ and $700^{\circ}C$, respectively. For the result of FT-IR analysis, the sample treated at $700^{\circ}C$ showed a reduced C-O absorption band compared with that of egg shell treated at $105^{\circ}C$, which may be due to the $CO_2$ release. Unlike to the result of FT-IR analysis, the XRD patterns of egg shell were almost similar for the cases of $105^{\circ}C$ and $700^{\circ}C$ treatment. however, characteristic diffraction pattern of CaO was observed for $850^{\circ}C$ treatment, at which $CaCO_3$ is known to be completely converted to CaO. TGA/DTA analysis showed a slow decline in weight loss up to $600^{\circ}C$ and, for $600{\sim}800^{\circ}C$ range, the weight loss became drastic by reason of $CO_2$ discharge, which was accompanied by an appearance of major endothermic peak. The ratio of practical breakthrough time to ideal one, total transfer unit, and mass transfer coefficient were observed to be increased as the adsorption was progressed in a multiple-column fixed-bed reactor using egg shell as an adsorbent, which signified the distribution effect of mass transfer for continuous adsorption reaction. The neutralization effect of egg shell for several types of acidic wastewater made of different mineral acids was not much different from each other except for the case of $H_2SO_4$, for which the neutralization reaction was thought to be retarded by the formation of gypsum.