• Journal of the Korean Society for information Management
• /
• v.32 no.1
• /
• pp.23-41
• /
• 2015

This study worked on the qualitative analysis about nomenclature East Sea by the record type in researches related to East Sea shown in the scientific journals. Here in this study, the way of marking is classified as three: 'sole notation of East Sea', 'sole notation of Sea of Japan', and 'simultaneous notation of both'. Based on a total of 4,192 selections from Web of Science DB, the analysis was followed up for change in time series by the notation type, notation type according to the nation that authors belong to, difference in research topic, impact factor, collaboration in research, and co-authorship network. The result turned out in this work that the sole notation of Sea of Japan accounted for the largest portion. It also showed that the rates of sole notation of East Sea and simultaneous notation have kept increasing continuously since the 1990s. Hub nations regarding the research of East Sea is five including Japan, Russia, Korea, USA, and China. In the case of sole notation of Sea of Japan, active collaboration studies are performed in USA, Russia, and China with a focus in Japan. In the case of sole notation of East Sea and simultaneous use, the research rate is relatively high in USA and Japan with a focus in Korea. As to the co-authorship network in the sole notation of Sea of Japan, sort of a "giant component" among different groups has been set up and through which the collaborative works are actively underway. However, it was found that the research of sole notation of East Sea is dispersed into small groups on the base of relevant individual institution.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.2
• /
• pp.186-194
• /
• 2020

In this study, spectral analysis was conducted to identify environmental factors af ecting short-term changes in water temperature in the East, West and South coasts of Korea. The data used in the spectrum analysis is the 2016 summer water temperature, air temperature, tide level and wind data provided by Korea Hydrographic & Oceanographic Agency. In power spectrum results, peaks of water temperature and tide level were observed at same periods in West Sea (Incheon, Pyeungteak, Gunsan and Mokpo) and South Sea (Wando, Goheung, Yeosu, Tongyeong and Masan) where mean tidal range was more than 100 cm. On the other hand, periodicity of water temperature did not appear in East Sea and Busan where the mean tidal range was small. Coherence analysis showed that water temperature was highly correlated with tide in West Sea and three stations(Wando, Goheung and Tongyeong) of South Sea. Especially, correlation between water temperature and tide level in Wando and Tongyeong presented 0.96 at semi-diurnal period. Water temperature in Yeosu seems to have influenced by tide and inflow of fresh water. In Masan, water temperature is influenced by south wind, tide and inflow of fresh water. In East Sea, influence of tide on water temperature is small due to current and small tidal range. As a result of comparing the time series graph, stations where the correlation between water temperature and tide is high show that relatively cold water was inputted at flood tide and flow out at ebb tide. short-term variation of water temperature was affected by tide, but long-term variation over a month was affected by air temperature.

• Korean Journal of Construction Engineering and Management
• /
• v.18 no.1
• /
• pp.65-73
• /
• 2017

Today, the United States, Europe and other advanced organizations are utilizing the concept of competency-based HR management. Recently, many organizations in Korea are also managing workforces by introducing the concept of job competencies in personnel management. However, in spite of the current trend, domestic human resources management methods for construction managers continues to operate by asking about work experience, licensing, education level, etc. This is a seniority system and it functions separately from an assessment of practical job competencies for the business. Moreover, construction management work has been very fragmented in terms of expertise and capacity depending on the type of management work and project progress. Therefore, it is necessary to develop a competencies management system for each business segment to effectively manage job competencies that reflect the the characteristics of a construction manager' s work. As such, the aim of this study is to analyze human resources management methods pertaining to domestic construction managers and present challenges and limitations in current practices. In particular, factors affecting the job competencies of construction managers are analyzed statistically. The results of this study will be used as the basis for future research into development of a construction manager competency management system.

• Journal of Life Science
• /
• v.23 no.11
• /
• pp.1360-1364
• /
• 2013

Petasin extracted from Petasites japonicus leaves has been well known to be effective in the treatment of allergic asthma. This study was carried out to optimize the extraction process of petasin from P. japonicus leaves by response surface methodology (RSM). The dried powder of P. japonicus leaves was extracted at ethanol concentrations ranging from 40% to 80%, extraction rpm ranging from 125 rpm to 225 rpm, and extraction time ranging from 1 to 3 hours. The effects of the extraction conditions on the dry yield and petasin content of the extracts were investigated using a second-order Box-Behnken design. The petasin content was significantly affected by ethanol concentration, extraction rpm, and extraction time, tending to increase more with increasing ethanol concentration. The optimum condition for petasin extraction from Petasites japonicus leaves was 79.92% in ethanol concentration, 178.10 rpm in extraction rpm, and 2.06 hours in extraction time, respectively.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.11 no.4
• /
• pp.85-93
• /
• 2008

The MAEULSOOP, Korean traditional village groves have been installed and survived since 7th Century to serve local village dwellers as a community forest. The common sense of their reasons for being is related to the surroundings such as hills, waterways and wind-ways. To understand the roles in a local community, spatial characteristics of distribution, locations and shapes were tested at the two-characterized regions, the Southwestern Flat Region and the Eastern Hilly Region. Approximately more than 500 written evidences related to trees and forests were surveyed, for example village names, folk tales and lists of designated trees for protection. Twenty sites in each region were selected and tested for the spatial analysis. Aerial photographs, DEM and the ArcGIS with a modified AML for slope analysis are applied based on the criteria of the KLCIS(Kwon, 2002; 권진오, 2008). The major factors in the role of the MAEULSOOP based on the spatial character of two regions are; the array and locations of hills for encircling or exposure, locations against corridors and waterway or not, locations of the community to serve, the conservation of energy. Although locations and shapes of the MAEULSOOP are slightly different, it seems that one of the prime roles is what makes their everyday life difficult the most in the community.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.4
• /
• pp.211-219
• /
• 2006

The UET(ultrasound excited thermography) for the ,eat-time diagnostics of the object employs an infrared camera to image defects of the surface and subsurface which are locally heated using high-frequency putted ultrasonic excitation. The dissipation of high-power ultrasonic energy around the feces of the defects causes an increase In temperature. The defect's image appears as a hot spot (bright IR source) within a dark background field. The UET for nondestructive diagnostic and evaluation is based on the image analysis of the hot spot as a local response to ultrasonic excited heat deposition. In this paper the applicability of VET for fast imaging of defect is described. The ultrasonic energy is injected into the sample through a transducer in the vertical and horizontal directions respectively. The voltage applied to the transducer is measured by digital oscilloscope, and the waveform are compared. Measurements were performed on four kinds of materials: SUS fatigue crack specimen(thickness 14mm), PCB plate(1.8 mm), CFRP plate(3 mm) and Inconel 600 plate (1 mm). A high power ultrasonic energy with pulse durations of 250ms Is injected into the samples in the horizontal and vertical directions respectively The obtained experimental result reveals that the dissipation loss of the ultrasonic energy In the vertical injection is less than that in the horizontal direction. In the cafe or PCB, CFRP, the size of hot spot in the vortical injection if larger than that in horizontal direction. Duration time of the hot spot in the vertical direction is three times as long as that in the horizontal direction. In the case of Inconel 600 plate and SUS sample, the hot spot in the horizontal injection was detected faster than that in the vertical direction

• Journal of the Mineralogical Society of Korea
• /
• v.31 no.4
• /
• pp.267-275
• /
• 2018

The purposes of this study were to analyze the mineralogical characteristics of slaked lime used for wall repair of traditional buildings in Bagan, Myanmar and to evaluate the physical properties of lime plaster produced by the same method as Bagan region. In the X-ray diffraction and thermal analysis of the Myanmar slaked lime, portlandite ($Ca(OH)_2$) and brucite ($Mg(OH)_2$) were detected as main constituent minerals, and a carbonate rock mainly composed of dolomite ($CaMg(CO_3)_2$) minerals may be used as a raw material to make slaked lime. The field-emission scanning electron microscope analysis showed that the Myanmar slaked lime was composed of irregularly shaped crystals of $0.5{\mu}m$ or larger and a small amount of $0.1{\mu}m$ of plate - like crystals. The size and uniformity of crystals in Myanmar lime is different from that of Korea slaked lime. This may be attributed to the effect of the mineral composition and the lime hydration method of Myanmar, which produces slurry by immersing the burnt lime in excess water for a long period of time. The compressive strength of the lime plaster in Myanmar resulted in a mean value of $1.13N/mm^2$ for the specimens cured for 28 days. The strength of the specimens with Bale juice was $1.03N/mm^2$, respectively. The lime is an air setting material that exhibits strength through long carbonation process. Therefore, it is necessary to evaluate physical properties according to curing period through long-term curing over 28 days in the future.

• Polymer(Korea)
• /
• v.29 no.2
• /
• pp.183-189
• /
• 2005

Films of poly(vinyl alcohol)(PVA)/chitosan blends and its blend hydrogels were prepared by the solution casting method. The state of miscibility of the blends and blend hydrogels were examined over the entire composition range by differential scanning carorimetry (DSC), thermogravimetry (TGA), and dynamic mechanical analysis (DMA). DSC analysis shows the depression of melting point of PVA in the blends and the decrease of crystallization temperature of PVA in the blends were observed with increasing chitosan content in the blends. TGA analysis indicates that chitosan was thermally more stable than PVA and the thermal stability of PVA in the blends was higher than that of pure PVA, due to some interactions between two component polymers in the blend. The glass transition temperature $(T_g)$ of the chitosan and of PVA, measured by DMA, were at 160 and $90^{\circ}C$, respectively. The $T_g$ of the blends was changed with the content of chitosan in the blends. The results of thermal and viscoelastic analysis indicate some miscibility between component polymers in the blend exists. Moisture and cross linking in the blend and blend hydrogel, which strongly change thermal and physical properties of hydrophilic polymers, affected the miscibility of chitosan and PVA to a small extent.

• Korean Journal of Soil Science and Fertilizer
• /
• v.33 no.6
• /
• pp.377-383
• /
• 2000

The composition of primary minerals of sand fractions and secondary minerals of clay fractions were investigated on the polder soils developed from alluvio-marine deposits near to Sapgyo-lake, constructed a sea dike across river estuary located in the west coast. The effects of a topographical sequence on the physico-chemical properties and mineralogical characteristics were evaluated using XRD, DTA, and TG with the chemical composition of $H^+$ saturated clays. Soils located on the seashore side were more silt fraction, higher pH and exchangeable cations than the others. The dominant minerals of soil parent materials are in the order of quartz, feldspars, micas, chlorite and amphibole. According to the greater distance from the lake, the amount of 1:1 minerals increased, but 2:1 minerals decreased. The dominant clay minerals of polder soils are kaolinite, vermiculite and illite. Hydroxy interlayer minerals are abundant in the clay fractions derived from the soil parent materials which have relatively low soil pH.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2003.04a
• /
• pp.35-35
• /
• 2003

)를 금속와이어에 인가하면 저항발열에 의해 와이어가 미세한 입자나 금속증기상태로 폭발하는 현상을 이용한 것으로 기상합성법에 속한다고 할 수 있다. 선폭법은 다른 제조법에 비해 공정이 간단하여 생산비용이 저렴하며, 원재료의 조성을 갖는 분말의 합성과 금속간화합물, 융점차이가 나는 재료의 합금화 등이 가능하다. 인가에너지의 크기와 폭발 시 분위기를 제어함으로써 분말의 평균크기와 분포 제어 또한 가능하다. 본 연구는 러시아의 우수한 기초기술을 바탕으로 Pb-Sn계 합금은 전기폭발법으로 극미세분말을 제조하였으며, 분말의 형상, 상 화학조성의 변화를 조사하였다. 본 실험에 사용된 Sn-Pb계(All-Union State Standard 1499-70, 0.53mm)합금와이어는 자동시스템(1-0.6Hz)에 의해 챔버안으로 공급되었다. 이 때 임계폭발 와이어 길이는 50-80nm으로 실험을 행하였다. 챔버 압력은 1.4~2.0atm으로 유지하였다. 제조된 분말의 특성은 XRD, XRPES, SEM등을 이용하여 분말의 형상과 상, 화학조성, 표면분석을 행하였으며 DSC, TGA, BET분석을 통하여 온도변화에 따른 금속분말의 열량변화, 질량변화, 비표면적을 측정하였다. 제조된 Sn-Pb계 분말은 모두 평균 입도 117nm~220nm의 구형형상이었다. 이때 합금분말의 조성은 51.17~63.21 at%Sn, 35.47~46.37 at%Pb로 나타났다. 와이어에 인가되는 비에너지(W/Wc)가 감소된에 EK라 표면층의 Pb함량이 증가함을 보였다. 이는 와이어 내부 저항의 감소로 인한 공정시간의 지연과 Sn, Pb의 확산계수 차이에 의한 것으로 사료된다. 열분석 결과, Sn~Pb계 화합물의 융점은 167~$169^{\circ}C$로 관찰되었으며, $10^{\circ}C$/min로 $920^{\circ}C$까지 승은 하였을 때 17.1~18 wt%의 질량증가를 보였다.TEX>계 나노복합분말이 얻어짐을 알 수 있었다. 이 때 X션 회절피크의 line broadening으로부터 복합분말의 Fe 명균 결정립 크기는 24nm로 초미세 결정럽의 분말합금이었다. 포화자화값은 볼밀처리에 따라 점점 증가하여 MA 30시간에는 20.3emu/g로 포화됨을 알 수 있었다. 또한 보자력 Hc는 MA초기단계에 350e로 매우 낮으나 30시간 후에는 Hc값이 2600e로 매우 큰 값을 나타내었다. 이것은 환원반응결과 초기에 생성된 Fe의 결정립이 비교적 크고 결정결함이 적으나 볼밀처리를 30시간까지 행하면 Fe 결정렵의 미세화 빛 strain 증가로 magnetic hardening이 일어나기 때문인 것으로 사료된다.길이가 50, 30cm인 압출재를 제조하였다. 열간압출한 후의 미세조직을 광학현미경으로 압출방향에 평행한 방향과 수직방향으로 관찰하였고, 열간 압출재 이방성을 검토하기 위하여 X선 회절분석을 실실하여 결정방위를 확인하였다. 전기 비저항 및 Seebeck 계수 측정을 위하여 각각 2$\times$2$\times$10$mm^3$ 그리고 5$\times$5$\times$10TEX>$mm^3$ 크기의 시편을 준비하였다.준비하였다.전류를 구성하는 주요 입자의 에너지 영역(75~l13keV)에서 가장 높은(0.80) 상관계수를 기록했다. 넷째, 회복기 중에 일어나는 입자들의 유입은 자기폭풍의 지속시간을 연장시키는 경향을 보이며 큰 자기폭풍일수록 현저했다. 주상에서 관측된 이러한 특성은 서브스톰 확장기 활동이 자기폭풍의 발달과 밀접한 관계가 있음을 시사한다.se that were all low in two aspects, named "the Nonsignificant group". And the issues were high risk perception in general setting and lo