• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.64-70
• /
• 2005

The overall results of hot firing tests of fuel-rich gas generator with impinging injector at design and off-design points are described. The gas generator consists of an injector head with impinging injector, a water cooled combustor wall, a turbulence ring to enhance mixing, an instrument ring measuring temperature and pressure and a nozzle. The combustion tests were successfully performed without damage of gas generator. Test results show that the outlet temperature is not dependent on residence time of hot gas within 4～6msec but dependent on chamber pressure. The relation between outlet temperature and combustion efficiency resulting from measured pressure, mass flow rate and area of nozzle throat is shown. The overall O/F ratio is the critical parameter to determine the outlet temperature and the linear correlation between two parameters is established.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.12
• /
• pp.1121-1126
• /
• 2010

This study is to investigate the effects of aromatics and T90 for low cetane number (CN) fuels on combustion and exhaust emissions in low-temperature diesel combustion. We use a 1.9-L common rail direct injection diesel engine at 1500 rpm and 2.6 bar BMEP. Low temperature diesel combustion was achieved via a high external EGR rate and strategic injection control. The tested fuels four sets: the aromatic content was 20% (A20) or 45% (A45) and the T90 temperature was $270^{\circ}C$ (T270) or $340^{\circ}C$ (T340) with CN 30. Given the engine operating conditions, the T90 was the stronger factor on the ignition delay time, resulting in a longer ignition delay time for higher T90 fuels. All the fuels produced nearly zero PM because of the extension of the ignition delay time induced by the low cetane number. The aromatic content was the main factor that affected the NOx and the NOx increased with the aromatic content.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.1
• /
• pp.18-24
• /
• 2015

An experimental investigation was conducted to figure out the effects of the inlet air temperature on the combustion efficiency using the fuel grains which were highly loaded with boron carbide. The results showed that the normalized combustion efficiency increased with the inlet air temperature, apparently the result of enhanced combustion of the boron particles. Even though the combustion efficiency is increased, the overall efficiency through the semi-empirical method, is decreased with the increasing inlet air temperature. Brayton cycle analysis has been performed using the heat input parameter and combustor Mach number, those two parameters are important role for the performance and similar trends are shown at the experimental results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.274-280
• /
• 2005

Experimental investigations were carried out in an atmospheric pressure, optically accessible and laboratory-scale dump combustor. The objective of this study is to obtain the phase-resolved gas temperatures at different phases of the oscillating pressure cycle during unstable combustion. To see the effect of incomplete fuel-air mixing on phase-resolved temperature characteristics, CARS temperature measurements were performed. Results including phase-resolved averaged temperature, normalized standard deviation and temperature probability distribution functions (PDFs) were provided in this paper. It could be found that the profile of mean temperature showed the in-phase relationship with pressure cycle. Temperature PDFs give an insight on the flame behavior as well as NOx emission characteristics. These results would be expected to play an important role in better understanding of driving mechanisms and thermo-acoustic interactions.

• Journal of Energy Engineering
• /
• v.19 no.3
• /
• pp.156-162
• /
• 2010

3-D CFD(Computational Fluid Dynamics) work were carried out to investigate the combustion characteristics in a boiler depending on the variations in air supply condition. For the gas temperature, $O_2$, NO, SOx at the outlet of economizer, the predicted values were been compared with the measured data. With the verified CFD model, the effects of air flow rates through SOFA(Separated Over Fire Air) and CCOFA(Closed Coupled Over Fire Air) on the combustion behavior in a boiler were simulated, and the distributions of NOx and gas temperature were mainly compared each other. The change in SOFA air flow rate gave the more sensitive effect on NOx than that in CCOFA. The distributions of gas temperature at convection path are differed with the changes in SOFA and CCOFA flow rate, so the combustion modification such as yaw anlge adjustment are required to get an enhanced gas temperature distribution.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3370-3375
• /
• 2014

MILD combustion is a highly favored technology for solving the trade-off relation between high thermal efficiency and low pollutant emissions. The system has low NOx concentration in high temperature combustion by recirculating the combustion gas, as well as improving the thermal efficiency by making the internal temperature in a combustion furnace uniform. This study describes the combustion characteristics of a conical MILD combustor in a laboratory-scale furnace by adjusting the equivalence ratio with the fuel gas flow rate while maintaining a constant air flow rate of the furnace. The MILD regime in the furnace is well characterized and the in-furnace temperature and emissions were predicted, respectively, for the range of equivalence of 0.69 - 0.83. For the range of equivalence ratios, this study confirmed the existence of a stable flame region that has an approximately $300^{\circ}C$ temperature difference between the maximum flame temperature region and main reaction region.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.2
• /
• pp.92-97
• /
• 2005

A series of combustion test was done to verify the optimization result of a gas generator for a 10 ton thrust liquid rocket engine. An injector element is F-O-F impinging type injector and the test was conducted with kerosene/LOX propellants. Test results of combustion temperature and pressure show a very good agreement with optimal design result and verify that the design method was properly established. And turbulence ring revealed its effectiveness in enhancing combustion gas mixing and temperature difference in the radial direction showed only less than 15K. Also turbulence ring induced only 3.2% pressure loss in the combustion chamber, which is far less than conventional level observed in a gas turbine engine. Axial temperature distribution also shows that turbulence ring could effectively reduce about 10% or more in gas generator length if its location is properly selected.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.3
• /
• pp.54-61
• /
• 1998

A numerical simulation is attempted for the regenerative cooling heat transfer processes of the liquid propellant rocket engine. The heat transfer from the combustion gases to the thrust chamber wall is called gas side heat transfer. This heat is conducted radially to the coolant through the carbon deposit and metallic wall of thrust chamber Finally, this heat is convected away by the coolant flowing along the passages in the thrust chamber. The equivalence of these three heat fluxes of the above processes is utilized to determine the coolant side wall temperature, gas side wall temperature and the heat flux. When the number and shape(width, height) of coolant passages, the shape(size) of thrust chamber, oxidant and fuel properties, coolant properties, oxidant/fuel mixture ratio, coolant inlet temperature, the thickness of carbon deposit formed along the thrust chamber wall during combustion are given, reasonable radial direction temperature distributions and heat fluxes along the thrust chamber axis are obtained.

• Journal of Energy Engineering
• /
• v.13 no.2
• /
• pp.112-117
• /
• 2004

Volatile organic compounds (VOCs) are low calorific value gases (LCVG) emitted from chemical processes such as painting booth, dye works and drying processes etc. Characteristics of VOCs are low calorific values less than 150kcal/㎥, high activation energy for ignition and low energy output. These characteristics usually make combustion unstable and its treatment processes needs high-energy consumption. The cyclone combustion system is suitable for LCVG burning because it can recirculate energy through a high swirling flow to supply the activation energy for ignition, increases energy density In make a combustion temperature higher than usual swirl combustor and also increases mixing intensity. This research was conducted to develop optimized cyclone combustion system for thermal oxidation of VOCs. This research was executed to establish the effect of swirl number with respect to the combustion temperature and composition of exhausted gas in the specific combustor design.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.173-178
• /
• 2003

The study was performed to understand combustion characteristics of the slinger combustor. Liquid fuel is discharged radially outwards through injection holes drilled in the high speed rotating shaft. We observed atomizing characteristics with variation of fuel nozzle rotating speed by using PDPA system. The mean drop diameter highly depends on fuel nozzle rotating speed. In KARI combustion test facility, Ignition and combustion tests were performed by using real scale combustor. In the test results, ignition and combustion efficiency were increased according to increasing fuel nozzle rotating speed. The measured radial temperature distribution at the combustor exit shows stable and fairly good distribution.