• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.29 no.1
• /
• pp.30-38
• /
• 1993

In this study, the combustion characteristics in a pre-combustion chamber diesel engine was investigated with experimental conditions of marine engine load. The heat release analysis used was a single-zone single-chamber thermodynamic analysis based on pre-combustion chamber pressure-time data. Based on the results of this investigation, the following conclusions were reached: 1) Increasing the load, peak pressure was increased and position of P sub(max) was retarded in crank angle degrees. 2) Ignition delay time was almost constant without relating to the load and the heat values to form a combusitible mixture were decreased apparently with increasing the load. 3) In premixed-combustion mode, the pattern of heat release rate was resembled without relating to the load and premixed-combustion time was shortened with increasing the load. 4) Increasing the load, mass of premixed-burned fuel was increased slightly, but was invariable beyond a certain fuel-air ratio. 5) Increasing the load, premixed-burned fraction was decreased.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.9 no.4
• /
• pp.237-245
• /
• 2011

As necessity of safety re-evaluation for spent fuel storage facility has emphasized after the Fukushima accident, accuracy improvement of heat load evaluation has become more important to acquire reliable thermal-hydraulic evaluation results. As groundwork, parametric and sensitivity analyses of various storage conditions for Kori Unit 4 spent fuel storage pool and spent fuel depletion parameters such as axial burnup effect, operation history, and specific heat are conducted using ORIGEN2 code. According to heat load evaluation and parametric sensitivity analyses, decay heat of last discharged fuel comprises maximum 80.42% of total heat load of storage facility and there is a negative correlation between effect of depletion parameters and cooling period. It is determined that specific heat is most influential parameter and operation history is secondly influential parameter. And decay heat of just discharged fuel is varied from 0.34 to 1.66 times of average value and decay heat of 1 year cooled fuel is varied from 0.55 to 1.37 times of average value in accordance with change of specific power. Namely depletion parameters can cause large variation in decay heat calculation of short-term cooled fuel. Therefore application of real operation data instead of user selection value is needed to improve evaluation accuracy. It is expected that these results could be used to improve accuracy of heat load assessment and evaluate uncertainty of calculated heat load.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1832-1833
• /
• 2011

석탄연소 화력발전소 보일러의 최적 제어는 부하요구에 대하여 보일러 출력을 신속히 제어하고, 보일러 출력에 대하여 보일러 입력에너지인 석탄 유량을 조절하여 에너지 균형을 맞추는 것이다. 이는 안정된 부하뿐 아니라 부하변동시에도 균형을 유지하면서 제어해야 한다. 석탄 연소 보일러 에너지 입력이 되는 석탄유량 측정 및 보정은 유류나 가스연료보다 까다롭고, 석탄 연료의 발열량이 시간에 대하여 변하는 문제가 있으므로, 신속하고 안정된 제어 성능을 위해 계측된 석탄 유량을 설계기준치로 환산, 보정하여 제어해야 한다. 이에 대한 기술은 일찍이 보일러 출력인 증기 보유열량을 측정하여 실제 계측한 석탄 유량을 연속적으로 보정하는 기법을 사용하고 있다. 이에 대한 석탄 열량 보정 제어로직을 검토하여 최적 튜닝방안에 대하여 고찰하고자 한다.

• Journal of Energy Engineering
• /
• v.18 no.3
• /
• pp.156-162
• /
• 2009

Cylinder-pressure based combustion analysis provides a mechanism through which a combustion researcher can understand the combustion process. This paper was to identify the most significant sources of cycle-to-cycle combustion variability in a spark ignition engine at idle. To analyse the cyclic variation in the test engine, the burn parameters are determined on a cycle-to-cycle basis through analysis of the engine pressure data. The burn rate analysis program was used in the analysis of the data. Burn parameters were used to determine the variations in the input parameter-i.e., fuel, air, residual mass, and so on.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.25 no.2
• /
• pp.82-86
• /
• 1989

This paper is concerned with the effects of temperature of diesel fuel on combustion characteristics and engine performance in a home-made precombustion diesel engine for small-sized fishing boat. The results may be summarized as follows: 1. The fuel injection timing was delayed with increase in temperature for diesel fuel, and remarkably delayed at low load. 2. The point of maximum pressure was delayed with increase in temperature for diesel fuel, the maximum pressure decreased with increase in temperature for diesel fuel but increased with increase in load. 3. The brake specific fuel comsumption (BSFC) decreased with increase in load, the optimum temperature of the heated fuel was about 15$0^{\circ}C$. 4. The smoke emissions increased with increase in load and temperature for diesel fuel.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.6
• /
• pp.51-58
• /
• 2019

In this study, a set of performance tests on 3D-printed combustor components were carried out to investigate the performance of 3D-printed component and its feasibility for micro gas turbine engines. The test were conducted for four different equivalence ratios under two different engine operating conditions. The measurement results show that the tested combustor had a low total pressure loss coefficient and a uniform exit temperature distribution. However, the combustion efficiency values are less than 93.5% owing to the large amount of UHC and CO, which is considerably lower than a typical gas turbine engine combustor. The performance data obtained from the tests will be used for combustor performance improvements using 3D-printing technology.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.4
• /
• pp.365-371
• /
• 2014

A numerical simulation was conducted for the combustion chamber of a 4-step grate-firing boiler for wood pellet fuel. The flame is extended to the exit of combustion chamber, which is reproduced by present numerical method based on a homogeneous reaction model. Flow field from the simulation shows a strong recirculation flow at the upstream corner of the chamber, along which the flame is extended to the exit. These combustion and flow characteristics remain unchanged for partial load operations, which suggest modification of the combustion chamber structure rather than resizing should be effective to improve combustion characteristics. Possible modifications for combustion chamber are suggested such as relocating its exit, increasing the number of grate steps or installing internals such as guide baffles.

• Journal of Energy Engineering
• /
• v.22 no.2
• /
• pp.169-174
• /
• 2013

An experimental study has been conducted for the design of the regenerative oxy-fuel combustion system with ceramic ball. Various design parameters are considered such as ball size, regenerator weight, and combustion load. Regenerative system with a pair of oxygen burners and regenerators is set up and the temperature of oxygen and exhaust gas passing through ball regenerator is measured. It is shown that the temperature distributions with time are affected by ball diameter and regenerator weight, and the significant temperature change is observed by combustion load. As the ball size decreases and the regenerator weight increases, the regenerating temperature efficiency increases. It is found that the heat recovery ratio is low despites of high regeneration temperature efficiency.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1997.10a
• /
• pp.70-77
• /
• 1997

표면연소버너의 모재 중 최근 많은 관심을 끌고 있는 금속섬유를 이용한 LPG 및 COG의 연소특성을 파악하였다. 연소모드, 매트 표면온도분포, 공해물질 배출량, 버너 전후단 압력 손실을 측정한 결과, COG 연소시가 더 넓은 범위의 적열영역을 얻을 수 있었고, 매트의 평균 표면온도도 높았다. NOx 발생량은 100ppm 이하였고, 연소부하 50kcal/$ extrm{cm}^2$hr에서의 매트 전후단의 압력손실은 30mmH2O로 압력손실은 거의 없었다. 적열범위나 표면온도분포 등이 가스별로 약간의 차이를 보였으나, 매트의 종류에 크게 상관없이 안정연소를 달성할 수 있어 가스 특성이 상이한 각종 가스의 연소에 표면연소기술의 적용이 가능할 것이다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.498-503
• /
• 1998

본 연구는 밀폐형 표면연소기의 모드해석 및 주파수특성의 실험을 통해 음향모드의 발생기구 및 발생조건을 구하기 위한 것이다. 연소장치의 치수변화와 부하, 당량비 등의 변화에 따른 진동특성의 변화를 실험하고 모드해석에 의한 예측결과와 비교고찰하여 음향모드의 특성을 밝혔다.