• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.1
• /
• pp.19-26
• /
• 2010

A PEMFC(proton exchange membrane fuel cell) is a good candidate for residential power generation to be coped with the shortage of fossil fuel and green house gas emission. The attractive benefit of the PEMFC is to produce electric power as well as hot water for home usage. The thermal management of PEMFC for RPG is to utilize the heat of PEMFC so that the PEMFC can be operated at its optimal efficiency. In this study, thermal management system of PEMFC stack is modeled to understand the dynamic response during load change. The thermal management system of PEMFC for RPGFC is composed of two cooling circuits, one for controling the fuel cell temperature and the other for heating up the water for home usage. The different operating strategy is applied for each cooling circuit considering the duty of those two circuits. Even though the capacity of PEMFC system (1kW) is enough to supply hot domestic water for residence, heat-up of reservior takes some hours. Therefore, in this study, time schedule of the simulation reflects the heat-up process. Dynamic responses and operating strategies of the PEMFC system are investigated during load changes.

• Membrane Journal
• /
• v.33 no.3
• /
• pp.127-136
• /
• 2023

In this study, the electrochemical performance of a 5-layer fuel cell stack using silica composite membranes as polymer electrolyte membranes was evaluated. It was observed that the flow rate of the fuel gases plays a crucial role in stack performance, particularly being mainly dependent on the flow rate of hydrogen. Increasing the flow rate of oxygen resulted in negligible changes in performance, whereas an increase in the flow rate of hydrogen demonstrated performance improvements. However, this led to an imbalance in the ratio of hydrogen to oxygen flow rates, causing significant degradation in stack performance and durability. A decline in stack performance was also observed over time due to the degradation of stack components. This phenomenon was consistently observed in individual unit cells. Based on these findings, it was emphasized that, in addition to optimizing the performance of each component during stack operation, it is important to optimize design and operating conditions for uniform flow rate control. Lastly, the developed silica composite membrane was assessed to have sufficient performance for application in actual fuel cell systems, exhibiting a performance of over 25 W based on maximum power.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.342-350
• /
• 2009

Fuel cells convert a fuel together with oxygen in a highly efficient electrochemical reaction to electricity and water. Since the electrochemical reaction in the fuel cell stack dose not generate any noise, Fuel cell systems are expected to operated much quieter than combustion engines. However, the tonal noise and the broad band noise caused by a centrifugal compressor and an electric motor cause which is required to feed the ambient air to the cathode of the fuel cell stack with high pressure. In this study, the multi-camber perforated muffler is used to reduce noise. We propose optimized muffler model using an axiomatic design method that optimizes the parameters of perforated muffler while keeping the volume of muffler minimized.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.6 s.39
• /
• pp.45-53
• /
• 2006

Turbo-blower as an air supply system is one of the most important BOP (Balance of Plant) systems for FCV(Fuel Cell Vehicle). For generating and blowing compressed air, the motor of air blower consumes maximum 25% of net power, and fuel cell demands a clean air. In this study, turbo-blower supported by air foil bearings is introduced as the air supply system used by 80kW proton exchange membrane fuel systems. The turbo-blower is a turbo machine which operates at high speed, so air foil bearings suit their purpose as bearing elements. Analysis for confirming the stability and endurance is conducted. The rotordynamic stability was predicted using the numerical analysis of air foil bearings and it is verified through experimental works. In spite of various transient dynamic situation, the turbo-blower had stable performances. After the performance test, results are presented. The normal power of driving motor has about 1.6 kW with the 30,000 rpm operating range and the flow rate of air has maximum 160 SCFM. The test results show that the aerodymic performance and stability of turbo-blower are satisfied to the primary goals.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.67-72
• /
• 2006

Blower as an air supply system is one of the most important BOP (Balance of Plant) system fur FCV(Fuel Cell Vehicle). For generating and blowing compressed air, the motor of air blower consumes maximum 25% of net power and fuel cell demands a clean air. Considering the efficiency of whole FCV, low friction lubrication of high speed rotor is needed. For the purpose of reducing electrical power and supplying clean air to Fuel cell, oil-free air foil bearings are applied at the each side of brushless motor (BLDC) as journal bearings which diameter is 50mm. The normal power of driving motor has 1.7kW with the 30,000rpm operating range and the flow rate of air has maximum 160 SCFM. The impeller of blower was adopted a mixed type of centrifugal and axial which has several advantages for variable operating condition. The performance of turbo-blower and parameters of air foil bearings was investigated analytically and experimentally. From this study, the performance of the blower was confirmed to be suitable far 80kw PEM FC.

• Transactions of the Korean hydrogen and new energy society
• /
• v.30 no.6
• /
• pp.556-566
• /
• 2019

Recently, as the supply of residential polymer electrolyte membrane fuel cells (PEMFCs) increases, the durability and lifetime of the PEMFC system are becoming important. The related studies have been mainly focused on the durability and lifetime of materials while the research on the durability and maintenance of the system level is insufficient. In this paper, a model-based fault detection method is developed considering an air supply system that is dominant to the system performance and efficiency. A commercial 1 kW residential fuel cell system is built, and experiments are conducted under various operation loads and states (normal, 6 faults). From the experimental data, nominal models and residuals are generated. With the residual pattern obtained from real-time data, the detection and classification of various faults can be possible. The technical importance of this paper is to minimize extra sensor installation by using the empirical model rather than a complex mathematical model, and to decrease the number of models by using the applicable model at three loads. Finally, the model-based fault detection method for the air supply system of a PEMFC is established and is expected to be applicable to other subsystems.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.1
• /
• pp.1-11
• /
• 2021

POGO is a dynamic axial instability phenomenon that occurs in liquid-propelled rockets. As the natural frequencies of the fuselage and those of the propellant supply system become closer, the entire system will become unstable. To predict POGO, the propellant (oxidant and fuel) tank in the first stage is modeled as a shell element, and the remaining components, the engine and the upper part, are modeled as mass-spring, and structural analysis is performed. The transmission line model is used to predict the pressure and flow perturbation of the propellant supply system. In this paper, the closed-loop transfer function is constructed by integrating the fuselage structure and fluid modeling as described above. The pogo suppressor consists of a branch pipe and an accumulator that absorbs pressure fluctuations in a passive manner and is located in the middle of the propellant supply system. The design parameters for its design optimization to suppress the decay phenomenon are set as the diameter, length of the branch pipe, and accumulator. Multiple-objective function optimization is performed by setting the energy minimization of the closed loop transfer function in terms of to the mass of the pogo suppressor and that of the propellant as the objective function.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.32-32
• /
• 2017

2012년부터 도입된 "신재생에너지 의무할당제(RPS)"로 인하여 500MW이상의 설비 용량을 갖춘 발전소의 경우 총발전량에서 일정 비율을 신재생에너지로 공급하여야 한다. 이러한 신재생에너지 중 농업부산물은 목질계 바이오매스의 한 종류로 '탄소중립(Carbon Neutral)' 연료이며 기존 화석연료와 혼소로 활용 할 수 있는 장점을 지니고 있다. 그러나 낮은 발열량, 운송 및 저장비용, 일정하지 않은 연소특성의 문제로 인하여 대부분 노지에 방치되거나 버려지고 있다. 이러한 버려지는 농업부산물을 효율적으로 활용하기 위한 방법 중 하나로 반탄화(Torrefacation) 처리가 대두되고 있다. 반탄화 처리 시, 발열량이 증대되며, 저장과 이송에서의 이점을 갖게 된다. 그러나, 반탄화는 공정 과정중 질량손실에 따른 에너지 총량의 감소한다는 단점을 가지고 있다. 이에 본 연구에서는 효율적인 반탄화공정을 위한 질량감소모델을 제시 하고자한다. 승온 속도(heating rate)를 $7.5^{\circ}C/min$, $15^{\circ}C/min$, $22.5^{\circ}C/min$의 조건에서의 열중량분석 결과를 토대로 속도모델식(Arrhenius method, Ingraham & Marrier method 등)을 적용하여, 반응속도상수를 도출하였다. 이 반응속도상수를 이용하여 질량감소 모델을 정립하였고, 이를 실험결과와 비교, 검증하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.2
• /
• pp.32-39
• /
• 2005

The effectiveness of the pogo suppression device (PSD) on the response of the piping system simulating the fuel (or oxidizer) supply lines of the rocket engines was investigated. The system response defined as the ratio of the flow rate to the pressure in the main tube was obtained for various PSD gas volumes $((0\~2)\times10^{-3}m^3)$ and three different baffle hole diameters (5, 50, 115mm). Existence of a gas volume in the PSD reduced the system resonance frequency. With a larger gas volume, the resonance frequency became lower, but only slightly, while the fluctuations of the main tube pressure and the flow rate damped down considerably. The resonance frequency decreased with the increase of the PSD inlet restriction (or the decrease of the baffle hole diameter), though slightly. However, with a larger inlet restriction, the PSD pressure wave showed a delayed response with the smaller amplitude compared to the pressure variation in the main tube.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.250.1-250.1
• /
• 2010

최근 석유공급 불안정성과 이산화탄소 배출 규제 움직임에 대응하기 위한 수단으로 바이오연료의 공급이 전세계적으로 증가하고 있다. 이와 같은 바이오디젤의 보급 활성화는 식물성 기름의 가격 상승과 수급 불안정 문제, 그리고 식량자원과의 충돌 문제를 야기하고 있다. 국내 바이오디젤 생산 원료로 사용되는 대두, 유채, 해바라기, 팜 등은 모두 식용시장과 수급 균형을 형성하고 있어 바이오디젤의 생산이 증가하게 되면 식용 오일 시장의 수급균형이 깨져 오일곡물 가격의 변동을 초래하게 될 것이다. 과거에는 수거비용을 들여 폐기하던 폐식용유 마저 이제는 돈을 주고 구입해야하는 실정에 다다랐다. 바이오디젤 생산비의 70~80%를 차지하는 원료유의 부족 현상에 따라 바이오디젤 업계에서는 soapstock, trapped grease, 폐식용유 등의 저급유지 활용 방안을 강구하고 있으며 자트로파와 같은 비식용 작물의 해외플랜테이션도 진행하고 있다. 본 연구에서는 커피찌거기에 남아 있는 오일을 속슬렛추출장치를 이용해 추출하고 전이에스테르화 반응을 수행하여 반응 특성과 커피오일 바이오디젤의 지방산 조성을 알아보고 바이오디젤 원료유로서의 사용가능성에 대해 알아보았다. 석유에테르를 용매로 속슬렛 추출장치를 이용해 추출시 원료대비 약 17%(w/w)의 오일을 추출할 수 있었다. 추출된 오일의 산가는 18.79mgKOH/g으로 매우 높아 직접 전이에스테르화 반응이 불가능하다. 고체 산 촉매 하에서 전처리 반응을 실시하여 유리지방산을 전환 제거한 후 염기촉매를 이용해 전이에스테르화 반응을 진행한 결과 약 80%의 바이오디젤(FAME) 함량을 얻을 수 있었다. 지방산 조성 분석 결과 리놀레익산(Linoleic acid, C18:2), 올레익산(Oleic acid, C18:1), 팔미틱산(Palmitic acid, C16:0)이 대부분을 차지하며 이 중에서도 리놀레익산이 44.17%로 가장 많은 함량을 보였다. 이는 커피찌꺼기 추출 오일이 바이오디젤 원료유로 활용 가능성을 나타내는 결과로, 색소성분 등의 불순물을 효율적으로 제거하여 증류정제 전단계에서의 바이오디젤 순도와 생산 수율을 증대시키기 위한 추가 연구가 필요한 것으로 판단된다.