• Proceedings of the KAIS Fall Conference
• /
• 2001.05a
• /
• pp.84-86
• /
• 2001

본 논문에서는 고성능 활성탄의 악취 및 유해가스 흡착효율과 멜트브로운(M/B)부직포의 여과성능에 의한 복합적인 고기능 방진특성을 갖는 활성탄 부착 M/B 국산화 여과재를 제조개발하였다. 고성능 활성탄은 고순도의 일반활성탄에 금속염, 유기물 등을 담지시켜 활성화시킨 활성탄이고, M/B여과재의 웹(web)제조조건은 M/B 방사기에서 방사온도 250℃, 방사속도 150m/sec, 고온공기온도 250℃ 그리고 DCD(die to collector distance) 20cm가 적합함을 알 수 있었다. 또한 M/B 여과재에 활성탄 부착은 열롤러시스템에 의한 열적결합방법을 이용하여 균일한 분포의 점접착결합구조를 갖도록 하였고, 개발된 복합기능 여과재가 방진마스크용 여과재로의 이용이 가능하다는 것을 분진포집효율, 투과율, 흡기저항 등 여과재 성능기준실험 결과를 통해 확인하였다.

• Journal of Wetlands Research
• /
• v.14 no.4
• /
• pp.471-478
• /
• 2012

The objective of the study is to find a way to utilize MSWI slag as filter material and to verify it. To do so, stability as filter material was tested, and used Ju-Munjin filter sand as control group to run actual filtering experiment to analyze filtering efficiency. According to result, MSWI slag is usable within designated waste acceptable standards. Also, it showed similar level of filtering capability to filter sand. Thus, MSWI slag could help to save and recycle resources if used as filtering material instead of filter sand As result of filtering test, SS and COD showed about same level of filtering capability similar to standard filter sand. MSWI slag has shown 26.96% higher with T-N, and 6.55% higher with T-P compared to standard filter sand. Also, remove efficiency comparison result with No. 40#(0.43mm) and mixed diameter showed equal or greater filtering capability.

• Clean Technology
• /
• v.7 no.3
• /
• pp.161-167
• /
• 2001

A model was proposed for the removal of poly-dispersed suspended solid by deep bed filtration and the collection efficiency was investigated by computer simulation. Deposited particles on the collector surface may act as additional collector and reduce the pore size of the collector. As a result, the capability of removing suspended particles of the filter bed was improved with the deposition. The filtration process of poly-dispersed suspension shows higher collection efficiency than that of mono-dispersed suspensions. Since the large particles deposited on the collector surface may contribute to the increase of contact between collectors and small particles, the improved overall collection efficiency was obtained.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.5
• /
• pp.5-12
• /
• 2018

The porosity formation by the addition of additives was found to be the highest in the case of aluminum powder 3% and $Ca(OH)_2$ 2% under the condition that strength was maintained. The optimum mixing ratio of the binder was shown to be the most effective at (Ash+Food waste+clay):(water glass+colloidal silica) 7:3, and the temperature response is most economical and effective at $1,000^{\circ}C$. The optimal mixing ratio is the strength in 30% of ash, 30% of clay and 10% of food waste, which is the effective in non-point pollution water treatment. Filter media produced under optimal mixing conditions were analyzed as $SiO_2$ 65.8%, density $1.4g/cm^3$, porosity 25.6%, pH 9.8, and no hazardous substances were detected. As a result of the filtration of the water treatment, the mean concentration of the filtered SS was $14.06mg/{\ell}$, and the removal efficiency of SS was 90%, the recovery rate of the reversal is 97.1%. This enables the development of filter media considering economic efficiency and efficiency as well as the utilization of waste resources, enabling high value added of waste resources.

• Journal of Energy Engineering
• /
• v.3 no.2
• /
• pp.172-178
• /
• 1994

고온, 고압하에서 효율적으로 분진을 제거하는 고온 여과재는 IGCC의 Hot Gas Cleaning, 화학공정 등에 유용하게 사용될 수 있으며 전세계적으로 pilot 또는 semicommercial scale로 연구개발 중에 있다. 본 논문에서는 디스크형(50 $\times$10t) 섬유형 여과재를 제조하여 $600^{\circ}C$에서 제철, 유리, 제지 및 석탄화력발전소 배출분진을 이용한 성능시험을 수행하였다. 개발된 여과재의 저항계수는 1010―5$\times$1011의 범위에 존재하였고 총집진효율은 99.7%이상의 높은 효율은 나타내었다. 또한 분진의 표면여과 속도는 10cm/sec로 기존여과 집진기의 5배이상으로 유지하였고 탈진강도 2기압, 탈진시간 0.1초에서 효율적인 집진 및 탈진이 되었다.

• Journal of Korea Water Resources Association
• /
• v.35 no.2
• /
• pp.213-220
• /
• 2002

This reserch was focused upon experimental study for wastewater reuse and conducted to evaluate optimum operating conditions of rapid filtration process such as filter flow rate, filtration time and backwashing condition for reuse of secondary-treated effluent using the pilot plant installed in real wastewater treatment plant. Also, the experiment on treatment char-acteristics of coagulant-added activated sludge process was performed to compare with activated sludge succeeded to rapid filtration. As the filtration velocity was 100m/day, the filtration time of the rapid filter connected with activated sludge system was revealed to 40 hours. Backwashing of filter was conducted by water wash and air scour. The optimum backwashing time and backwash flow rate were 10min and 10LPM, respectively. The quantity of backwashing water of the rapid filter was about 2% of total treated water.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.3 no.1
• /
• pp.519-523
• /
• 1960

• Fire Science and Engineering
• /
• v.31 no.4
• /
• pp.7-11
• /
• 2017

The use of special gas masks such as PAPR is strongly required for the safe and efficient work of fire-fighters in removing fire residue and rescue activity. Special gas masks commonly use canisters with carbon activated particles. This paper analyzed the pressure distribution, velocity distribution and pressure loss characteristics in canisters using CFD simulation, and showed pressure drops are affected by inlet air velocity, canister geometry and increase dramatically especially with the decrease of particle diameters and volume fractions.

• Analytical Science and Technology
• /
• v.21 no.3
• /
• pp.167-173
• /
• 2008

In order to solve the reproduction problem of PCB, we carried out poly chlorinated biphenyl (PCB) removal at low temperature (< $220^{\circ}C$), which could not take place reproduction of PCB by over 90% on catalyst. We coated catalyst to commercial bag filter for simultaneous removal of PCB and particle. It was found that PCB could be not reproducible due to it's decomposition of benzene ring. The coating method of spray type was more useful than that of precipitation one. PCB removal conversion was highest on the Pt-Co catalyzed bag filter. The data of this study can be well used in order to remove PCB and particle simultaneously for incinerator process by substituting commercial bag filter to catalyzed bag filter.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.327-327
• /
• 2021

하수재이용에서 전처리 막여과 공정은 완벽한 고액분리로 인해 후단 역삼투막 손상을 줄일 수 있는 공정으로 각광을 받고 있다. 일반적으로 막여과 공정은 여과->물리세정->충진->여과 와 같은 제막사에서 제공하는 운전 사이클에 맞춰 적용하고 있으며 유지세정 역시 1회/일 또는 1회/주 단위로 정해진 범위에서 수행되고 있다. 이러한 운전 방식은 시시각각 변화하는 막 유입수질에 적절하게 대응하지 못해 장기적으로 막오염 발생에 따른 생산수량 감소는 물론 막오염 제거를 위한 화학세정 주기가 짧아져 전체적인 생산수량이 감소하는 원인이 되고 있다. Raffine(2012)에 따르면 가역적 막오염의 경우 Flux 증가에 큰 영향이 없으나 비가역적 막오염은 Flux 증가에 따라 급격히 증가한다고 보고하고 있으며 이는 제한된 분리막 면적당 처리수 생산량을 증가시키기 위해 비가역적 막오염의 발생량을 줄이는 것이 필요하며 이를 위해 주기적인 강화역세(Chemical Enhanced Backwashing, CEB)가 도입되고 효율적인 유지세정 방법에 대한 연구가 진행되고 있다. 당사에서는 일산에 있는 I 수질복원센터내에 25 m³/일 규모의 막여과 하수재이용 파일롯 플랜트를 설치하고 막여과 하수재이용 공정의 운영 효율을 높이기 위하여 W사에서 개발한 IntelliFluxControl(IFCr) 소프트웨어를 이용하여 하수재이용 막여과 성능을 확인 하였다. IFCr은 실시간으로 변화하는 수질에 따른 막오염 정도에 따라 역세 강도 및 빈도와 CEB 적용 정도를 변화시켜 분리막 운전의 효율을 높일 수 있는 운영 소프트웨어이다. I 수질복원센터의 하수 방류수를 막여과 유입수로 적용하여 40 LMH를 기준으로 IFCr을 적용하지 않은 경우 23.7일 운전 가능하였으나 IFCr을 적용한 경우 50일 연속 운전이 가능하였다. 또한 역세척수를 운전 기간 동안 약 50 m³을 사용한 반면 IFCr을 적용한 경우 이에 절반 수준인 24.1 m³ 만 사용하여 회수율이 91%에서 95%로 증가한 것을 확인 할 수 있었다. 본 연구의 결과는 기존의 제막사에서 제시하는 막 공정 운영방법을 탈피하여 분리막이 갖고 있는 성능을 최대한 끌어 올릴 수 있는 연구 결과라고 판단되며 향후 스케일 업 연구를 통해 실제 플랜트에 적용 가능성이 확인 될 경우 시설의 설치 막모듈 개수와 유지관리비를 동시에 절감할 수 있는 기술이 될 수 있을 것이다