• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.5
• /
• pp.427-438
• /
• 2019

It was important to estimate the full-scale operating performance including actual RPM and engine power of a ship since the operation efficiency during a voyage could be evaluated from the values. In the previous research, an entire voyage was simulated by following recorded speeds obtained from AIS and full-scale measurement data. Although reasonable tendencies were observed in the estimated speed, actual RPM, and engine power, it was impossible for them to be completely corresponded with the measured values due to the difference between actual operation and mathematical model. In this paper, alternative approaches to cope with the speed, actual RPM, and engine power were suggested by following the given speed, RPM, and power respectively. After entire voyages were simulated according to a given value, the effects of the value on the estimated performance were investigated. And, it was confirmed that the appropriate approach could be differently chosen according to the aim of the simulation or given value.

• Journal of the Korean Institute of Gas
• /
• v.25 no.2
• /
• pp.34-41
• /
• 2021

In order to cope with the problems that may occur when the natural gas used in Korea becomes low in calories, the problems that may have to the domestic industrial gas equipment must be identified in advance, and based on this, countermeasures for efficient use of energy must be preceded. In this study, in order to solve the problem of deterioration of engine output performance and efficiency due to the introduction of low calorific gas when using a lean-burning natural gas engine that complies with the EURO-6 regulation, specific control plans and results based on the experiment are intended to be presented. In order to identify the improvement effect by the control variable represented by the ignition timing under the full load condition at the engine speed of 1,400 rpm and 550 Nm, 2,100 rpm, which is the engine speed at the rated operation condition, the thermal efficiency and exhaust gas characteristics were identified and optimized by changing the ignition timing for each gas fuel. In the case of pure methane, which shows the lowest value based on the torque under the full load condition, if the ignition timing is advanced by about 2 CAD from the reference ignition timing, the torque can be compensated without a large increase in NOx emission.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.1
• /
• pp.67-74
• /
• 1998

The primary cause of air pollution by vehicles is imperfect combustion of fuel. One of the most usual causes of this imperfect combustion is the misfire in IC engins. The U.S. EPA(Environment Protection Agency) and the CARB(California air Resources Board) have imposed regulations for the detection of misfiring in automotive engines. The OBD-II regulations require that misfire should be monitored by the engine diagnostic system, and that the goal of OBD-II is to alert the driver to the presence of a malfunction of the emission control system. Several solutions to the misfire detection problem have been proposed for the detection of misfires. However, the performance of these methods in the presence of misfire is not altogether clear. This paper presents a precise method and system for internal combustion engine misfire. Present invention based upon measurements of engine roughness as derived from crankshaft angular velocity measurements with special signal processing method. Crankshaft angular velocity signals are processed by WDPT, so that the more reliable misfire detection than the time domain analysis. Experimental work confirms that it is possible to apply the WDFT for the detection of misfires in no-load idle and road testing.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.5
• /
• pp.380-388
• /
• 2019

Jet engine modulation(JEM) signals are widely used for target recognition. These signals coming from a potentially hostile aircraft provide specific information about the jet engine. In order to obtain the number of blades, which is uniquely provided by the JEM signal, one must extract the spool rate, which is the rotation speed of the blades. In this paper, we propose an algorithm to extract the spool rate from a weak JEM signal. A criterion is developed to extract the spool rate from the JEM signal by analyzing the intensity of the JEM signal component. The weak signal is first subjected to a high-pass filtering-based process, which modifies it to facilitate spool rate extraction. We then apply a peak detection process and extract the spool rate. The technique is simpler than the existing CEMD or WD method, is accurate, and greatly reduces the time required.

• Journal of KSNVE
• /
• v.4 no.3
• /
• pp.264-272
• /
• 1994

동력을 발생하거나 이를 이용하는 대부분의 기계장치는 회전하는 축계 장치 를 갖고 있는데 이들은 중량을 갖는 회전체와 이것을 지지하거나 연결하는 강성축과 베어링으로 구성되므로 진동형태에 따른 고유진동수를 나타낸다. 그 결과 축계 장치 가 운전되는 동안 발생하는 기진력이 축계 강도를 초과하거나 진동수가 시스템의 공진점에 일치하던지 가까우면 이들 진동에 의해 축계 장치에 부착되어 있는 카프링, 감속기어, 지지베어링, 밀봉씰, 공정볼트 등이 이상마모 또는 피로파괴의 원인이 되므로 설계시나 운전중에 이에 대한 진동원인들을 PC를 이용하여 현장운전자들이 쉽게 규명할 수 있도록 개발하고 발생되는 진동문제를 효과적으로 해결할 수 있는 진동 저감장치를 몇 가지 소걔하였다. 국내에서 제작되는 선박, 자동차, 발전프랜트 또는 여기에 설치되는 엔진의 진동저감울 위해 이들 소프트웨어와 하드웨어들은 국내 관련기업의 현장기술 지도를 위해 여러차례 활용된 바 있으며 이를 이용하므로 써 축계진동 저감기술 자립은 물론 국산화 제품의 성능향상에도 크게 기여할 수 있다고 본다.

• Journal of the Korea Convergence Society
• /
• v.10 no.4
• /
• pp.131-138
• /
• 2019

Diesel engines have important advantages over its gasoline counterpart including high thermal efficiency, high fuel economy and low emissions of CO, HC and $CO_2$. However, NOx reducing is more difficult on diesel engines because of the high $O_2$ concentration in the exhaust, marking general three way catalytic converter ineffective. Two method available technologies for continuous NOx reduction onboard diesel engines are Urea-SCR and LNT. The implementation of the Urea-SCR systems in design engines have made it possible for 2.5l and over engines to meet the tightened NOx emission standard of Euro-6. In this study, we investigate the characteristics of NOx reduction with respect to engine speed, load, types of catalyst and the $NH_3$/NOx ratio and present the conditions which maximize NOx reduction. Also we provide detailed experimental data on Urea-SCR which can be used for the preparation for standards beyond Euro-6.

• 한국방재학회:학술대회논문집
• /
• 2010.02a
• /
• pp.45.2-45.2
• /
• 2010

자동차 주행 시 엔진회전수가 1,500rpm 이상이고 주행속도가 50km/hr 이상의 조건에서 가속 페달을 밟지 않은 상태로 관성주행(타행주행)을 하면 연료분사량이 "0"이 되고 그에 따라 엔진 배출 $CO_2$ 배출량도 "0"이 된다. 본 연구에서는 고속도로 및 자동차 전용도로에서의 이러한 연료차단(퓨얼컷 fuel-cut) 주행 구간을 찾고 연료차단 기능을 활용하는 경우 그 효과를 평가하였다. 본 시험의 결과 퓨얼컷 주행을 활용하면 약 4~5% 정도의 $CO_2$ 배출량을 줄일 수 있음을 알 수 있었고, 감속의 정도를 도로 상황에 맞게 최적화하는 경우 감소율을 더욱 향상시킬 수 있을 것으로 판단된다. 추후 본 시험의 결과를 이용하여 도로 내리막 구간에서 연료소모량 및 $CO_2$ 배출량을 저감하면서도 과속으로 인한 사고를 예방하는 방안으로 활용할 수 있을 것으로 판단된다.

• Journal of the Korean Institute of Gas
• /
• v.19 no.6
• /
• pp.47-53
• /
• 2015

This paper is to study applying for numerical analysis method for flow field, velocity and pressure of fuel on the low pressure pump using excavator. The pressure distribution of fuel pump certified the linear variation according to rotation angle of rotor. Especially, it knew the fact that the pressure in rotation angle $40^{\circ}$ appeared high outlet and low inlet of fuel pump. Also, this range angle can seek the fact that the leakage flow and velocity are the most increasing. And the more rotor rotation of fuel pump, the more mean outlet flow rate increased in linear. Whenever the gap size decrease with rotor and housing, the discharge flow rate could seek the approaching 0.0712kg/s that consider with theory discharge flow rate calculated from displacement between rotor gear and idle gear.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.202-203
• /
• 2011

본 논문에서는 자동차가 전기모터로 주행하다가 배터리가 방전되면 엔진으로 구동할 수 있도록 연결해 주는 클러치 시스템에 적용된 BLDC 모터의 위치제어기를 제안한다. 클러치 시스템에 사용되는 BLDC 모터의 구동은 Hall 센서로부터 검출된 회전자 위치정보를 이용하여 위치제어를 수행하였다. PHEV 시스템에서는 클러치를 엔진과 전기모터로 연결해야 하므로 정확하고 빠른 위치제어를 위해 위치제어기를 적용하였고, 클러치 연결 시 진동을 최소화하기 위해 속도제어기를 사용하여 엔진의 속도와 클러치 모터의 속도를 동기가 되도록 하였다. 또한 위치제어를 하기 전에 클러치의 초기위치를 맞춰 줘야 하므로 모터의 위치정보를 이용하여 속도제어기와 전류제어기로 모터를 일정한 위치로 이동시켰다. BLDC 모터의 전압제어를 위한 PWM 방법은 기존의 바이폴라 PWM 보다 전류리플이 적은 유니폴라 효과를 내는 새로운 바이폴라 PWM 방법을 사용하였다. 제안된 알고리즘은 시뮬레이션과 실험을 통해 검증하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.1-6
• /
• 2002

Engine lubrication system is generally affected by vehicle driving conditions, which are composed of acceleration, braking deceleration and accelerating during cornering. The major reason is due to the oil pan system in which oil is directly influenced by inertia farce caused by vehicle driving conditions. Therefore, to confirm safety of engine lubrication system inertia farce effects are also considered in the developing state. For the purpose, we have carried the engine tilting tests using ourselves made test rig. Verifying the test results we also measured the inertia effects on the engine lubrication system using the circular tuning and slalom test with vehicle. Through the comparison study between two kinds of results we obtained that the engine tilting test rig was very useful to confirm the safety evaluation of engine lubrication system.