• Proceedings of the Korean Information Science Society Conference
• /
• 2000.10c
• /
• pp.552-554
• /
• 2000

기존 워크플로우 시스템은 비즈니스 프로세스 내의 정보와 제어의 흐름 수행에 있어서 중앙 집중적인 워크플로우 엔진이 전체 실행의 모든 부분을 담당하고 있다. 이러한 워크플로우 시스템이 갖는 성능, 확장성 등 구조적 제약의 단점을 극복하기 위하여 워크플로우 엔진의 분산, 이동 에이전트의 적용, 웹 기반 등 다양한 연구가 진행되고 있다. 본 논문에서는 단위 업무 스케쥴링 기능과 관련된 정보를 분산된 형태로 참가자에게 일임하여 워크플로우 엔진 부하를 줄이고, 프로세스 인스턴스 단위의 이동 에이전트를 적용하여 비동기적 특성을 이용한 성능 및 확장성의 향상을 제공하는 워크플로우 시스템의 설계를 제안한다. 또한 제안한 시스템을 위하여 각 참가자별 스케쥴링 정보를 WfMC의 프로세스 정의 표준 언어인 WPDL로부터 추출하는 방법을 제안한다.

• Journal of Advanced Navigation Technology
• /
• v.14 no.1
• /
• pp.93-101
• /
• 2010

In this study, the performance characteristics of turbocharged engine is analyzed. The methods of engine performance improvements are suggested not only for full load characteristics of the engine but also for partial load characteristics of the engine, which is more frequently used in actual driving conditions. The compression ratio of the compressor is increased rapidly in a straight line pattern until 1260 engine rpm, and after that it is increased slowly to 2.5 ratio. Also the brake mean effective pressure increased until 1260 engine rpm and decreased rapidly after 1600 engine rpm. The higher the pressure ratio, the better the fuel consumption, air excess ratio and brake mean effective pressure. But those are higher in the rated revolution range than in the mid-low revolution range. The turbocharger is operated in a stable condition from 1260 rpm and its efficiency is low in the low speed range for the reason of its characteristics. The results of this study can be applied in the fundamental control methods of turbocharged engine for stable load and speed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.7
• /
• pp.1082-1091
• /
• 2004

Analyzed Parametrically was an internal combustion engine combined with gas turbine the cycle of which is splitted into compression side cylinder and expansion side one, and heat adding of which is during constant volume pressure, temperature process. The advantages of each measures were analyzed by means of thermal cycle diagram. The thermal efficiency of partial load cutting off firstly isothermal heat adding and secondly isobaric heat adding also was analyzed The authors suggested some potentials about the performance as for thermal efficiency, mean effective pressure and reducing emissions and noise supposed were the operating parameter of the engine set to some values and were some problems solved.

• Journal of Energy Engineering
• /
• v.27 no.2
• /
• pp.49-54
• /
• 2018

The common rail diesel engine used in this study is a remanufactured waste engine. The fuel injection timing of the waste engine is set to be suitable for the operating conditions of the vehicle. However, the engine of a generator is operated at a constant speed and mainly at partial load. Therefore, it is necessary to change the fuel injection timing suitable for the power generation engine, and the cost and the time required for such change must be minimized as much as possible. As a result of the analysis, it was confirmed that the fuel efficiency improves according to the fuel injection timing suitable for the engine for the generator, thereby increasing the performance and fuel efficiency.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.2
• /
• pp.13-21
• /
• 1986

점차 엄격해지는 요구조건을 만족시켜 주기 위해서는 승용차용 엔진의 실제특성과 운전특성을 지 배하는 설계변수의 조절은 불가피하며, 그중에서도 엔진의 핵심부인 연소질의 설계는 가장 중요 하다. 부분 부하에서의 SI기관의 연료경제성을 향상시키는 가장 좋은 방법이 압축비를 상승시 키는 것이므로, 앞으로의 여소실은 고압축비에서도 옥탄가가 높은 연료를 요구하는 성향을 낮 추는 특성을 갖고 있어야 한다. 새로운 엔진의 향상을 최적화하기 위하여는 quench area의 크 기와 위치 그리고 적절한 quench distance의 성질이 중요하며, 또한 연소실의 소형화, 스파크 플러크의 위치, 표면적/체적의 비 그리고 화염전파거리등도 고려에 넣어야 한다. 승용차용 엔진의 요구조건은 연소실을 피스톤 크라운에 위치시키는 용이한 방법을 통하여 해결될 수 있으며, 이 러한 형상의 연소실은 실린더 헤드에 장치한 연소실과 비교하여 다음과 같은 장점을 갖고 있다. - 스파크 플러그 주변에 연소실을 배치하기 쉽다. - 연소실 내에 quench area의 설정이 자유롭다. - 연소실 layout의 개조없이 압축비의 설정이 자유롭다. - 연소실의 조합이 간단하다. - 실린더벽으로의 열손실이 감소되어 열효율이 증대된다. - 공연비의 희박가능한계가 크다. - EGR성능이 향상되어 NOx 의 배출과 연료소비율이 감소된다. - 필요하다면 연소실실 또는 직접분사식 Diesel 기관으로서의 개조가 간단하다. 만약 생산단가가 크게 상승하지 않는다면, NOx의 배출과 연료소비율이 작으면서도, 비출력이 큰 4-밸브 연소실이 실용화 될 전망이다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.87-97
• /
• 2000

A steady state performance simulation and diagnostics program for the turboprop engine (PT6A-62), which is the power plant of the first developed military basic trainer KT-1 in Republic of Korea, was developed. The developed steady state performance analysis program was evaluated with the performance data provided by the engine manufacturer and with analysis results of GASTURB program, which is well known for the performance simulation of gas turbines. Performance parameters were discussed to evaluate validity of the developed program at various cases such as altitude, flight velocity and part load variation. GPA(Gas Pass Analysis) allows engine performance deterioration to be identified at the module level in terms of reduction in component efficiencies and changes in mass flow. In order to find optimal instrument set to detect the physical faults such as fouling, erosion and corrosion, a gas path analysis approach is utilized. This study was performed in two cases for selection of optimal measurement parameters. One case was considered with the effect of instrument number by changing independent parameter number. The other case was performed with selection of independent parameter set. According to the analysis results, the optimal measurement parameters selected were eight dependent variables such as shaft horsepower, fuel flow rate, compressor exit pressure and temperature, compressor turbine inlet pressure and temperature and power turbine inlet pressure and temperature.

• Journal of the Korean Institute of Gas
• /
• v.14 no.1
• /
• pp.8-14
• /
• 2010

In this study, we experimentally investigated a compression ignition engine operated with Bio-diesel blended LPG fuel. In particular, the performance, emissions characteristics (including total hydrocarbon, carbon monoxide, nitrogen oxides, and carbon dioxides emissions), and combustion stability of a CI engine fueled with Bio-diesel blended LPG fuel were examined at 1500 rpm. The percentage of Bio-diesel in the fuel blend ranged from 20-60%. The results showed that stable engine operation was possible for a wide range of engine loads up to 40% Bio-diesel by mass. When the Bio-diesel content was increased, leading to a decrease in the lower heating value of the blended fuel, the cetane value increased, resulting in a advanced start of heat release. Exhaust emission measurements showed that THC and CO emissions were increased when using the blended fuel at low engine speeds due to partial burn from over-mixing. NOx emission was emitted less at lower loads and more at higher loads.

• Journal of ILASS-Korea
• /
• v.21 no.1
• /
• pp.1-6
• /
• 2016

A gasoline injector rig which can measure cumulative injected fuel mass under a vehicle driving condition was developed. The measurement system consists of an engine control unit (ECU), data acquisition (DAQ) and injected fuel collection system using loadcells. By supplying reconstructed sensor signals which simulate the real vehicle's sensor signals to the ECU, the ECU drives injectors as if they were driven in the vehicle. The vehicle's performance was computer simulated by using $GT-Suite^{(R)}$ software based on both engine part load performance and automatic transmission shift map. Throttle valve position, engine and vehicle speed, air mass flow rate et al. were computer simulated. The used vehicle driving pattern for the simulation was FTP-75 mode. For reconstructing the real vehicle sensor signals which are correspondent to the $GT-Suite^{(R)}$ simulated vehicle's performance, the DAQ systems were used. The injected fuel was collected with mess cylinders. The collected fuel mass in the mess cylinder with elapsed time after starting FTP-75 driving mode was measured using loadcells. The developed method shows highly improved performance in fast timing and accuracy of the cumulative injected fuel mass measurement under the vehicle driven condition.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.2
• /
• pp.61-70
• /
• 2000

The performance simulation program on the turboprop engine(PT6A-62), which is a main engine of the first trainer KT-1 in republic of Korea, was developed. Characteristics of engine components were required for the steady-state performance analysis including on and off design point analysis. In most cases, these were substituted for what scaled from well known engine components characteristics with the scaling law. The developed program was compared with CASTURB program which is well known for the simulation performance analysis, such as analysis results of mass flow rate, compressor pressure ratio, fuel flow rate, power, specific fuel consumption ratio and turbine inlet temperature in the following four cases, to evaluate whether the developed program is acceptable or not. The first case was the sea level static standard condition and other cases were considered with various flight Mach numbers, altitudes. After verifying the developed program, the partload performance analysis was carried out. Transient performance analysis for various fuel schedules were performed. When the fuel step increase of 0.1sec was performed, the overshoot of the compressor turbine inlet temperature occurred. However, the fuel ramp increase for longer than 0.1sec time was performed, the overshoot could be eliminated.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.2
• /
• pp.47-55
• /
• 1998

Steady-state and transient performance for the medium scale civil aircraft turbofan engine was analyzed. Steady-state performance was analyzed on maximum take-off condition, maximum climb condition, and cruise condition. At 90％RPM of the low pressure compressor, the partload performance was economized. The transient performance was analyzed with cases of the step increase, the ramp increase, the ramp decrease, and the step increase and ramp decrease for the input fuel flow. For the transient performance analysis, work matching between compressor and turbine was needed. Modified Euler method was used the integration of residual torque in work matching equation. At all flight condition, the overshoot of the high pressure turbine inlet temperature was appeared in the step and ramp increase case, and the surge of high pressure compressor was appeared in the step increase case and the ramp increase case within 5.5 seconds of maximum climb condition.