• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.2
• /
• pp.257-268
• /
• 1994

An experimental study was carried out to elicit important factors causing cracks and rupture of steel members and their elements under imposed large repeated deformations, and of the quantitative relationships among the important physical factors leading to failure. Each of twenty-eight angles and nine thin-plates served as the specimen and was subjected to repeated axial load after undergoing inelastic buckling. Particular attention was paid to the effects of loading pattern, failure mode and cross-sectional shape on the very-low-cycle failure behavior under loading repetitions of the order of a few to twenty. The experimental results show that energy dissipation capacity depends heavily on the entire history of loading, the failure mode, the slenderness ratio and the width-to-thickness ratio. No simple quantitative relations were observed between the initiation of the visible cracks or rupture and the energy dissipation capacity. The maximum values of residual "net" strains are found to range from 25% to 40%, independent of the test parameters.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.68.2-68.2
• /
• 2010

Dye-sensitized solar cells (DSSC) show great promise as an inexpensive alternative to conventional p-n junction solar cells. Investigations into the various factors influencing the photovoltaic efficiency have recently been intensified. The conventional absorber electrode in DSSC is composed of compacted or sintered $TiO_2$ nanopowder that carries an anchored organic dye. The absorbance of incident light in the DSC is realized by specifically engineered dye molecules placed on the semiconductor electrode surface ($TiO_2$). The dye absorbs light at wavelengths up to about 920nm, the energy of the exited state of the molecule should be about 1.35eV above the electronic ground state corresponding to the ideal band gap of a single band gap solar cell. The dye molecules ar adhered onto the nanostrutured $TiO_2$ electrode by immersing the sintered electrode into a dye solution, typically 3mM in alcohol, for a long enough period to fully impregnate the electrode. However, the concentrations of the dye is slightly changed due to the evaporation of the alcohol. The dye is more expensive than other materials in DSSC and related to the efficiency of DSSC. Therefore, the concentrations of the dye should be carefully measured. In this study, we investigated to the dye loading on fired $TiO_2$ powder as a function of temperature by the TG-DTA and the dye solution by UV-visible spectroscopy after the impregnation process. The dye loading is related to the porosity of the nanostructured $TiO_2$ electrode.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.85.1-85.1
• /
• 2010

$Cu(In,Ga)Se_2$ (CIGS) thin film solar cell is currently 19.5% higher efficiency and developing a large area technology. The structure of CIGS solar cell that make five unit layers as back contact, light absorption, buffer, front transparent conducting electrode and antireflection to make them sequentially forming. Materials and various compositions of thin film unit which also manufacture a variety method used by the physical and chemical method for CIGS solar cell. The construction and performance test of evaporator for CIGS thin film solar cell has been done. The vapor pressures were changed by using vapor flux meter. The vapor pressure were copper (Cu) $2.1{\times}10^{-7}{\sim}3.0{\times}10^{-7}$ Torr, indium (In) $8.0{\times}10^{-7}{\sim}9.0{\times}10^{-7}$ Torr, gallium (Ga) $1.4{\times}10^{-7}{\sim}2.8{\times}10^{-7}$ Torr, and selenium (Se) $2.1{\times}10^{-6}{\sim}3.2{\times}10^{-6}$ Torr, respectively. The characteristics of the CIGS thin film was investigated by using X-ray diffraction (XRD), scanning electron microscopy/energy dispersive spectroscopy (SEM/EDS) and photoluminescence (PL) spectroscopy using a He-Ne laser. In PL spectrum, temperature dependencies of PL spectra were measured at 1137 nm wavelength.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.151.2-151.2
• /
• 2010

본 연구는 하이드로퀴논(HQ)을 이용하여 매립가스로부터 이산화탄소를 선택적으로 분리하고 유기 크러스레이트 형태로 분리 및 저장에 적용하기 위한 연구로써 하이드로퀴논을 다양한 객체가스와 반응시키면서 열역학적 안정영역을 파악하고 분광학적 방법을 이용하여 미세구조 변화를 분석하고자 하였다. 먼저 ${\alpha}$-HQ를 고압(4MPa)의 이산화탄소와 반응시켜 이산화탄소가 포집된 ${\beta}$-HQ를 합성하였고, 동공 내에 존재하는 이산화탄소를 제거하여 동공을 유지하는 empty ${\beta}$-HQ를 만들었다. 온도를 증가시키면서 XRD 패턴을 측정한 결과 298 K 에서 378 K 사이에서 ${\beta}$-HQ 시료는 서서히 empty ${\beta}$-HQ 의 구조로 전환되었으며 378 K 이상의 온도에서 ${\alpha}$-HQ 구조로 급격히 전환되었다. 또한 생성된 empty ${\beta}$-HQ 동공에 이산화탄소가 포집, 해리되는데 있어서 온도의 영향을 확인하기 위해 298K과 343K의 온도에서 실시간 라만분광법으로 측정하였다. 그 결과 298K에서 약 200분의 시간이 지난 후 이산화탄소는 하이드로퀴논 동공 내로 포집되어 안정화되었으며 압력해방 후에는 빠져나가지 않고 동공 내에 존재함을 확인하였다. 그러나 343K에서는 급격히 포집되어 30분 이내 안정화되었고, 압력해방 후 동공 내에 존재하지 못하고 빠져나가는 것을 확인하였다. Empty ${\beta}$-HQ의 이산화탄소 선택도를 관찰하기 위해 이산화탄소와 메탄, 수소, 질소의 조성이 각각 30%, 30%, 20%, 20%인 혼합가스와 반응시킨 후 가스 크로마토그래프 분석을 실시한 결과, empty ${\beta}$-HQ내 포집된 가스 중 이산화탄소의 조성이 약 80% 이상으로 나타나 높은 선택도를 나타냄을 관찰하였다.

• Journal of Korea Foresty Energy
• /
• v.20 no.1
• /
• pp.62-72
• /
• 2001

To elucidate the behaviors of alkali swelllng of woods. the dimensional change in cross section of cell elements of four major Korean woods during alkali swelling were examined by an optical microscory, an imaging analysis method and an X-ray diffrartion During alkali swelling, tracheid diameter of Larix kaempferi wood showed greater swelling property than that of Pinus koraiensis wood, and the cell wall swelled highly over 10% sodium hydroxide solution treatment. The radial diameter of vessel elements in earlywood shrunk, but it swelled slightly in tangential direction. When treated with 5% NaOH, the wall thickness of wood fiber increased about three times over the original one. The thickness of cell wall in all elements and the diameter of wood fiber and tracheid showed almost isotropic shrinkage. The diameter of cell elements during the mercerization process decreased, but cell wall thickness Increased. Crystal transformation of cellulose in wood was not occurred by alkali treatments. but relative crystallinity and crystallite width of the woods increased slightly. Consequently, it was demonstrated that the swelling properties of woods were dependant on wood species, cell elements and alkali concentration.

• Journal of Korea Foresty Energy
• /
• v.23 no.1
• /
• pp.26-37
• /
• 2004

This study was to investigate the rational propagation of the Vitex rotundifolia, which is distributed as a community naturally at coastal area in Korea. The germination rate of ordinary temperature stored fruits was the highest with 67%. In the matter of the number of seedlings per fruit, 1 seed germinated fruit was the most with 40.3 % and the mean was 1.4 seedlings per fruit. The best rooting rate of both greenwood and hardwood cutting was 96.7% in the case of cuttings soaked in IBA 2500ppm for 1 minute on the Compost+Sand bed-soils. Generally the root development of cuttings was higher in the high IBA concentration with soaking in a moment than in the low IBA concentration with soaking in long time, and bed-soils mixed with sands and composts. And in the rooting rate, greenwood cutting was better about 10% than hardwood cutting of Vitex rotundifolia.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.1 s.74
• /
• pp.33-43
• /
• 2005

This paper presents the test results and evaluations for the energy dissipation capacity and compressive performance of light-weight hybrid panels. A total of 26 full-scale specimens of light-weight hybrid panels were tested. The parameters include the presence of light-weight foamed mortar, the specific gravity of light-weight foamed mortar (0.6, 0.8, 1.0, 1.2), the finishing materials (light-weight foamed mortar, OSB [Oriented Strand Board], gypsum board), the shape of bracing (x, ~), and the size of panels (1P-900 mm 2,400 mm, 2P-1,800 mm 2,400 mm). The results of the cyclic tests are somewhat different from those of monotonic tests, due to the different specific gravity of light-weight foamed mortar. It was found from the compressive tests that the ultimate strength and initial stiffness are increased by means of light-weight foamed mortar (2~2.5 times in ultimate strength and 2~3 times in initial stiffness).

• Journal of Hydrogen and New Energy
• /
• v.31 no.1
• /
• pp.23-32
• /
• 2020

The intermittent characteristics of renewable energy complicates the process of balancing supply with demand. Electrolysis technology can provide flexibility to grid management by converting electricity to hydrogen. Alkaline electrolysis has been recognized as established technology and utilized in industry for over 100 years. However, high overpotential of oxygen evolution reaction in alkaline water electrolysis reduces the overall efficiency and therefore requires the development of anode catalyst. In this study, Raney Ni-Zn-Fe electrode was prepared by electroplating and the electrode characteristics was studied by varying electroplating parameters like electrodeposition time, current density and substrate. The prepared Raney Ni-Zn-Fe electrode was electrochemically evaluated using linear sweep voltammetry. Physical and chemical analysis were conducted by scanning electron microscope, energy dispersive spectrometer, and X-ray diffraction. The plating time did not changed the morphology and composition of the electrode surface and showed a little effect on overpotential reduction. As the plating current density increased, Fe content on the surface increased and cauliflower-like structure appeared on the electrode surface. In particular, the overpotential of the electrode, which was prepared at the plating current density of 320 mA/㎠, has showed the lowest value of 268 mV at 50 mA/㎠. There was no distinguishable overpotential difference between the type of substrate for the electrodes prepared at 80 mA/㎠.

• Journal of Hydrogen and New Energy
• /
• v.31 no.1
• /
• pp.8-22
• /
• 2020

In this study, we investigated the deactivation characteristics of Ni-Zn-Fe electrodes due to intermittent operation in alkaline water electrolysis. To find suitable method to accelerate deactivation of electrode, the accelerated stress-test (AST) which repeated on/off step was performed with constant current/voltage control. The AST under constant voltage control is suitable to deactivate electrode so it were selected to investigate deactivation of electrode. The AST which repeated on/off step in range of -1.3 V and 0 V was performed and the relationship between oxidation current and electrode deactivation in the off step was investigate. As results, it was confirmed that the nickel and zinc on electrode surface were oxidized due to anodic current which occurred at off step.

• KIPS Transactions on Computer and Communication Systems
• /
• v.6 no.11
• /
• pp.463-468
• /
• 2017

To sense a wide area with mobile nodes, the uniformity of node deployment is a very important issue. In this paper, we consider the coverage problem to sense big data in sparse mobile ad hoc networks. In most existing works on the coverage problem, it has been assumed that the number of nodes is large enough to cover the area in the network. However, the coverage problem in sparse mobile ad hoc networks differs in the sense that a long-distance between nodes should be formed to avoid the overlapping coverage areas. We formulate the sensor coverage problem in sparse mobile ad hoc networks and provide the solution to the problem by a self-organized approach without a central authority. The experimental results show that our approach is more efficient than the existing ones, subject to both of coverage areas and energy consumption.