• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.6
• /
• pp.533-542
• /
• 2014

In design standards such as AASHTO LRFD and Korea Highway Bridge Design, the dynamic behaviors under the impact loading has not been considered and it recommends of using a static force for designing bridge column against vehicle collisions. Accordingly, in this study, models of vehicle collisions to concrete bridge column were developed with various boundary conditions in order to take into account dynamic behaviour of the column. Cargo trucks of 10tons, 16tons and 38tons were selected and a typical type of concrete bridge pier column along the Kyungbu highway in Korea was selected for this study. Results from this study indicate that the static load specified in the design standards are too small compared to results obtained in this study. It was also found that a consideration of the bridge superstructure allowed smaller damages of concrete bridge pier column under truck impact loadings. Furthermore, a comparison study of direct impact analysis of vehicle to bridge-column with in-direct impact analysis using load-time history functions was performed. The in-direct impact analysis shows that the use of load-time history graph improves the computational cost up to 92% and predict the behaviors of the bridge column under the impact loadings well. The obtained load-time history graph could be easily applied to several existing models.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.2
• /
• pp.95-101
• /
• 2020

The wind turbine blades should be designed to possess a high stiffness and should be fabricated with a light and high strength material because they serve under extreme combination of lift and drag forces, converting kinetic energy of wind into shaft work. The goal of this study is to understand the basic knowledge required to curtail the process time consumed during the construction of small wind turbine blades using carbon fiber reinforced polymer (CFRP) prepeg composites. The configuration of turbine rotor was determined using the QBlade freeware program. The fluid dynamics module simulated the loads exerted by the wind of a specific speed, and the stress analysis module predicted the distributions of equivalent von Mises stress for representing the blade structures. It was suggested to modify the shape of test specimen from ASTM D638 to decrease the variance in measured tensile strengths. Then, a series of experiments were performed to confirm that the bladder compression molded CFRP prepreg can provide sufficient strength to small wind turbine blades and decrease the cure time simultaneously.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.2 no.1
• /
• pp.153-169
• /
• 2007

It is as result that study to apply mini magnet nerve curer in peripheral nervous system disease treatment. Design and embodied action power and Control Unit in cylinder form of magnet roof object firstly. Yielded service area about special quality of probe of roof object cylinder style and treatment area dimension and distance of treatment pulse secondly. Embody pulse forming course energy value by Probe's form by third, could embody treatment pulse by disease. Specially, through a special quality experiment, saved Damping pulse form and treatment pulse form etc. variously. Lately, embodied this to aid a little in disease treatment that follow that there is no invasion that there is no stimulation by medicine development. Go amplitude treatment pulse (traditional magneto-therapy of greatly great that strong) does curative effect greatest at short time and becomes thought that demand is magnified greatly at the future in this research.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.6
• /
• pp.959-972
• /
• 2017

In evaluation of blast-induced vibration, peak particle velocity (PPV) is generally calculated by using attenuation relation curve. Calculated velocity is compared with the value in legal requirements or the standards to determine the stability. Attenuation relation curve varies depending on frequency of test blasting, geological structure of the site and blasting condition, so it is difficult to predict accurately using such an equation. Since PPV is response value from the ground, direct evaluation of the structure is impractical. Because of such a limit, engineers tend to use the commercial numerical analysis program in evaluating the stability of the structure more accurately. However, when simulate the explosion process using existing numerical analysis program, it's never easy to accurately simulate the complex conditions (fracture, crushing, cracks and plastic deformation) around blasting hole. For simulating such a process, the range for modelling will be limited due to the maximum node count and it requires extended calculation time as well. Thus, this study is intended to simulate the elastic energy after fractured zone only, instead of simulating the complex conditions of the rock that results from the blast, and the analysis of response characteristics of the velocity depending on shape and size of the fractured zone was conducted. As a result, difference in velocity and attenuation character were calculated depending on fractured zone around the blast source appeared. Propagation of vibration tended to spread spherically as it is distanced farther from the blast source.

• Journal of Korean Association for Spatial Structures
• /
• v.8 no.3
• /
• pp.65-73
• /
• 2008

The present work deals with subjective assessments to propose the objective parameter related to the subjective attribute of reverberation in the coupled room varied the aperture opening size. A 1/10 scale model was built and used for the measurements and subjective assessments. For the subjective tests, binaural impulse responses(BIRs) were measured using a dummy head and the measured BIRs were convolved with anechoic recorded music for the presentation over the headphones. The results showed that the perceived reverberation was the largest in the aperture opening size 12.5%(1.97% of mail) room surface area)and decreased with increasing the aperture opening size over 25% (3.94% of main room surface area) in the main room coupled with the secondary reverberant room. In the main room coupled with the secondary absorptive room, there was no changes in the perceived reverberation up to the aperture opening size 6.25%(0.99% of main room surface area) and it gradually decreased with increasing the aperture opening site over 12.5%. The objective parameter, T30/T15, showed a very low correlation with the perceived reverberation in the coupled room varied the aperture opening size but showed a high correlation with a new objective parameter, T30/Tbp, proposed by the authors. Because the late part decay energy more rapidly increases with increasing the aperture opening site than the early and middle part decay energy, the LDT/EDT or T3/T1 is a better quantifier to measure double slopes in the coupled room than the T30/T15.

• Journal of Radiation Protection and Research
• /
• v.26 no.4
• /
• pp.393-398
• /
• 2001

The non-combustible RI wastes disposed of in hospital every year emit ${\gamma}$-ray or ${\beta}$-ray but their activities are very low to the extent of background. Development of more simple methods is needed because the conventional detection methods are so ineffective and complex. In this study, to solve this problem, detection method using efficiency curve for ${\gamma}$-ray emitting radioactive wastes measurement is proposed and experimental detection efficiency equation is also determined through HPGe's standard specimen measurement. For ${\beta}$-emitting radioisotopes detection, new measurement method using detection efficiency estimated by Monte Carlo simulation and SBD measurements is also proposed. According to the results of this paper, the unknown activity of low-level radioactive wastes without LSC requiring the preparation of standard sample and measurement for standard source detection efficiency could be determined efficiently and simply about ${\pm}17%$ in errors by using the theoretical detection efficiency and the SBD measurement result.

• Journal of Cadastre & Land InformatiX
• /
• v.50 no.1
• /
• pp.215-229
• /
• 2020

In response to the recent 4th industrial revolution, the demand for 3D object models in the latest fields of digital twin, autonomous driving, and VR/AR, as well as the existing fields such as city, construction, transportation, and energy has increased significantly. It is expected that the demand for 3D object models with various precision from LOD1 to LOD4 will increase more and more in various industry fields. However, the Ministry of Land, Infrastructure and Transport, and the local government and the private sector have partially built 3D object models of different precisions for some specific regions because of the huge cost. Therefore, this study proposes a feasible plan that can solve the cost problem in generating 3D object models for the whole territory. For our purpose, we first analyzed usage, demand, generation technology and generation cost for 3D object models. Afterwards, we proposed LOD3 model generation plan for all territory using automatic 3D object model generation technology based on image matching. Additionally, we supplemented the proposed plan by using LOD4 generation plan for landmarks and LOD2 generation plan non-urban area. In the near future, we expect this would be a great help in establishing a feasible and effective 3D object model generation plan for the whole country.

• Korean Chemical Engineering Research
• /
• v.56 no.1
• /
• pp.96-102
• /
• 2018

In this study, adsorption characteristics of coconut shell-based granular activated carbon (CS-GAC) on Basic Blue 3 (BB3) were evaluated. As the dosage of CS-GAC increased, the removal efficiency of BB3 tended to increase and the initial dye concentration of 50 mg/L was completely removed at 0.2 g dosage. Adsorption equilibrium achieved within 270 and 420 min at the initial concentrations of 25 and 50 mg/L, respectively, and the experimental data were represented by the pseudo-second-order model. The maximum uptakes ($q_{max}$) predicted by the Langmuir model were 34.45, 46.63 and 53.10 mg/g at 298, 308 and 318 K, respectively. The $q_{max}$ value increased as the temperature increased. Also, the Gibbs free energy (${\Delta}G$) was changed to -7.37, -8.19 and -10.40 kJ/mol with increasing temperature. The enthalpy change (${\Delta}H$) and the entropy change (${\Delta}S$) were 34.47 kJ/mol and 0.15 J/mol K, respectively. Therefore adsorption of BB3 by CS-GAC was spontaneous and endothermic.

• Korean Chemical Engineering Research
• /
• v.56 no.1
• /
• pp.66-72
• /
• 2018

Corn stover is known as a good candidate for a functional food ingredient when the main lignocellulosic material, lignin, is used as bioactive materials as form of polyphenolic compounds. The purpose of this study was to determine the microwave extraction conditions under which total phenolic compounds (TPC) and flavonoid contents of corn stover were maximized. Microwave-assisted extracts using sulfuric acid ranging from 0 to 1.0 mol with extraction time between 40 and 240 sec were conducted by using response surface methodology (RSM). Microwave power showed significant effects (p<0.05) and the concentrations of TPC and flavonoids increased with increased level of microwave power and extraction time. The optimum conditions for corn stover extraction were determined as 698.6 W, 240 sec, and 0 mol sulfuric acid, and the predicted value of TPC and flavonoid is 82.4 mg GAE/g DM and 18.1 mg/g DM, respectively. Microwave extraction was evaluated as an economic process with low energy consumption, short extraction and high extraction yield of bioactive including TPC and flavonoids compared to conventional extractions.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.9
• /
• pp.722-727
• /
• 2013

Medical treatment for animals is very difficult as the opinions of pets' masters take priority over treatment regardless of the seriousness of pets' disease or the needs of medical treatment. In case that a pet has heart disease, especially, it is difficult to get the direct answer from the pet's master on the decision or confirmation of treatment. For those reasons, it is almost impossible to predict and treat the pet before an emergency like the heart failure or an unexpected death happens. Using stethoscope can be the first diagnosis method to check the heart or any kinds of disease inside the body. High-tech equipments like CT, X-ray or Ultrasound can be used, but they can only be used as a second choice of diagnosis method since it requires professional skills and its high price. That's why stethoscope is still the best diagnostic tool when one makes the first diagnosis. In this study, we give a detailed account of digital diagnosis system in which veterinarians can analyze the sound from stethoscope without bringing it to their ears and make a diagnosis wherever they are. And we suggest a new concept of diagnosis system surrounding, which shows the relativeness of disease through Level Crossing Rate(LCR) and energy level from the stethoscope sound made in this system.