• The Journal of the Korea institute of electronic communication sciences
• /
• v.19 no.1
• /
• pp.39-46
• /
• 2024

In this study, GTZO(Ga-Ti-Zn-O) thin films were deposited at various working pressures (1~7mTorr) by RF magnetron sputtering to examine the structural, electrical, and optical properties. All GTZO thin films exhibited c-axis preferential growth regardless of working pressure, the GTZO thin film deposited at 1mTorr showed the most excellent crystallinity having 0.38˚ of FWHM. The average transmittance in the visible light region (400~800nm) showed 80% or more regardless of the working pressure. We could observed the Burstein-Moss effect that carrier concentration decrease with the increase of working pressure and thus the energy band gap is narrowed. Figure of merits of GTZO thin film deposited at 1mTorr showed the highest value of 9.08 × 103 Ω-1·cm-1, in this case resistivity and average transmittance in the visible light region were 5.12 × 10-4 Ω·cm and 80.64%, respectively.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.4
• /
• pp.183-193
• /
• 2006

This study deals with the response of reinforced concrete beams strengthened with carbon fiber sheets. Test beams are subjected to static loading and repeated loading. Based on the static test results of the RC beams strengthened with carbon fiber sheets, repeated loading tests are performed. The variables of repeated loading test are composed of the number of carbon fiber sheets, the existence of U-shaped band at the end for anchoring, and loading rate of repeated loading, etc. Test results show the flexural behavior, the characteristics of strength, the characteristics of ductility, the change of flexural rigidity, and the amount of energy loss of RC beams under monotonic incremental loading and repeated loading. The failure strain of carbon fiber sheets is also estimated under repeated loading. From the experimental results, this work presents a basis of the data needed to analyze and design the static and dynamic flexural response of RC beams strengthened with carbon fiber sheets.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.1
• /
• pp.1-8
• /
• 2013

This study focuses on a ship detection and tracking method using Frequency Modulated Continuous Wave (FMCW) radar used for horizontal surveillance. In general, FMCW radar can play an important role in maritime surveillance, because it has many advantages such as low warm-up time, low power consumption, and its all weather performance. In this paper, we introduce an effective method for data and signal processing of ship's detecting and tracking using the X-band radar. Ships information was extracted using an image-based processing method such as the land masking and morphological filtering with a threshold for a cycle data merged from raw data (spoke data). After that, ships was tracked using search-window that is ship's expected rectangle area in the next frame considering expected maximum speed (19 kts) and interval time (5 sec). By using this method, the tracking results for most of the moving object tracking was successful and those results were compared with AIS (Automatic Identification System) for ships position. Therefore, it can be said that the practical application of this detection and tracking method using FMCW radar improve the maritime safety as well as expand the surveillance coverage cost-effectively. Algorithm improvements are required for an enhancement of small ship detection and tracking technique in the future.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.1
• /
• pp.50-57
• /
• 2017

Zinc oxide is, one of metal oxide semiconductor, harmless to human and environment-friendly. It has excellent chemical and thermal stability properties. Wurtzite-zinc oxide is a large band gap energy of 3.37 eV and high exciton binding energy of 60 meV. It can be applied to various fields, such as solar cells, degradation of the dye waste, the gas sensor. The photocatalytic activity of zinc oxide is varied according to the particle shape and change of crystallinity. Therefore, It is very important to specify the additives and the experimental variables. In this study, the zinc oxide were synthesized by using a microwave assisted hydrothermal synthesis. The precursor was used as the zinc nitrate, the pH value was controlled as 11 by NaOH. Surfactants are the ethanolamine, cetyltrimethylammonium bromide, sodium dodecyl sulfate, sorbitan monooleate was added by changing the concentration. The composite particles had the shape of a star-like, curcular cone, seed shape, flake-sphere. Physical and chemical properties of the obtained zinc oxide was characterized using x-ray diffractometer, field emission scanning electron microscopy, thermogravimetric analysis and optical properties was characterized using UV-visible spectroscopy, photoluminescence and raman spectroscopy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.183-183
• /
• 2015

Indium tin oxide (ITO)는 넓은 밴드갭을 가지는 n-type의 축퇴 반도체로 태양전지, 스마트윈도우, 터치 센서, organic light emitting displays (OLEDs) 등에 널리 적용된다. 최근 touch screen panels (TSPs)의 높은 전기적 특성 및 고해상도 요구에 따라 고품질 ITO 박막개발의 수요도 증가하는 추세이다. 지금까지 ITO 박막의 물성 및 기계적 특성에 관한 많은 연구가 진행되어 왔지만 ITO 초박막 에서의 근본적인 물성 변화에 대한 연구는 미흡한 실정이므로, 이러한 연구는 필수적이라 할 수 있다. ITO 초박막은 광학적 특성은 우수하나, 낮은 결정성으로 인해 전기적 특성이 나쁘다는 단점을 가지며, 이러한 ITO 박막의 결정성은 초기 박막 성장과정에 많은 영향을 받는다. ITO 박막의 초기성장과정은 핵이 생성된 후(nucleation), 각각의 위치에서 성장하게 되고(growth), 합쳐지면서(coalescence) 연속적인 막을 형성 하는데(continuous), 이러한 초기 박막 성장 과정 중에 핵 생성 밀도를 증가시키고 박막이 연속적으로 되는 두께를 감소시킨다면, 더욱 더 고품질의 ITO 초박막을 얻을 수 있을 것이다. 따라서, 본 연구에서는 박막 초기 형성 과정 중 섬들이 합체되는 두께를 최소화시키기 위하여 EMF(electromagnetic field strength) 시스템을 이용하였다. EMF 시스템은 DC 캐소드에 전자석 코일을 장착하여 전자기장을 추가로 부가한 것으로, 이를 이용할 경우 스퍼터 원자가 중성상태로 기판에 도달하는 것이 아니라, 이온화되어 Vp-Vf의 차이로 가속되어 추가적인 에너지를 공급받음으로써 기판표면상에서 확산을 촉진시키므로 박막이 연속적으로 되는 임계 두께를 감소시킬 수 있는 것으로 기대된다. 실험은 실온에서 DC 마그네트론 스퍼터링법을 이용하였으며, 유리기판위에 4, 6, 8, 10, 12, 20 nm의 두께로 ITO 박막을 제작하였다. 스퍼터링 파워는 150 W (3.29 W/cm3), 작업 압력은 0.13 Pa, 기판과 타깃 사이의 거리는 70 mm였다. 각각의 두께에서 EMF 파워 0, 5, 10, 15, 20, 25, 30 W로 인가하여 박막을 제작한 후, EMF 파워에 따른 ITO 박막의 초기 성장 과정중 표면상태를 AFM (atomic force microscope) 이미지를 통하여 관찰하였다. 또한, 두께 약 8 nm에서와 20 nm일 때의 전기적 특성 및 광학적 특성을 관찰하였으며, 두 박막 모두 EMF 파워 15 W를 인가하였을 때 그 특성이 가장 향상되는 것을 확인하였다. 이러한 결과를 통하여 박막은 초기 성장이 중요하므로, 매우 얇은 두께에서 좋은 특성을 가진 박막을 제작하여야 박막의 두께를 증가시켰을 때도 좋은 특성의 막을 얻을 수 있음을 알 수 있었다. 또한, EMF 파워를 증가시킴에 따라 자장강도를 증가시키는 것과 같은 효과 즉, 플라즈마 임피던스가 감소하는 효과를 내어 증착 중 고 에너지 입자 (Ar0, O-)에 의한 박막손상이 감소한 것으로 판단된다. 따라서 적정 EMF 파워 15 W를 인가하였을때 가장 물성이 좋은 ITO 박막을 얻을 수 있었다. 즉, EMF 시스템을 이용하여 저온 공정에서 결함농도가 적은 고품질의 ITO 초박막을 제작할 수 있었다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.5
• /
• pp.202-206
• /
• 2014

In order to investigate the photoluminescence (PL) properties of $V_2O_5$ films, amorphous and crystalline films were prepared by using RF sputtering system, and the PL spectra of the films were measured at the temperatures ranging from 300 K to 10 K. In the amorphous $V_2O_5$ film grown at room temperature, a PL peak centered at ~505 nm was only observed, and in the crystalline $V_2O_5$ film, two peaks centered at ~505 nm and ~695 nm, which is known to correspond to oxygen defects, were revealed. The position of PL peak centered at 505 nm for both the amorphous and crystalline $V_2O_5$ films showed a strong dependence on temperature, and the positions were 2.45 eV at 300 K and 2.35 eV at 10 K, respectively. The PL at 505 nm was due to the band energy transition in $V_2O_5$, and also, the reduction of the peak position energy with decreasing temperature was caused by a decrement of the lattice dilatation effect with reducing electron-phonon interaction.

• Transactions of the Korean hydrogen and new energy society
• /
• v.10 no.1
• /
• pp.59-69
• /
• 1999

AlN thin films were fabricated by reactive sputtering for the application of MIS devices with Al/AlN/Si structure. It has investigated the surface morphology change, I-V characteristics, C-V characteristics, and chemical composition of AlN films with the intriducing time of hydrogen on the fixed deposition condition(RF power: 150W, sputtering pressure: 5mTorr, flow rate ratio of $Ar/N_2=1$, hydrogen concentration: 5%). By addition of the hydrogen the deposition rate decreased drastically whereas the surface morphology changed little. It has been found from the analysis of I-V and C-V characteristics curves that the films deposited with hydrogen addition in initial stage had lower leakage current density, lower flat band voltage and hystersis profile when compared with those with hydrogen addition in last stage. The oxygen concentration in AlN films decreased with addition of hydrogen gas, which suggesting a profitable role in the insulation and C-V characteristics of AlN films.

• Journal of the Korean Vacuum Society
• /
• v.22 no.6
• /
• pp.327-334
• /
• 2013

Long-wave infrared detectors using the type-II InAs/GaSb strained superlattice (T2SL) material system with the nBn structure were designed and fabricated. The band gap energy of the T2SL material was calculated as a function of the thickness of the InAs and GaSb layers by the Kronig-Penney model. Growth of the barrier material ($Al_{0.2}Ga_{0.8}Sb$) incorporated Te doping to reduce the dark current. The full width at half maximum (FWHM) of the $1^{st}$ satellite superlattice peak from the X-ray diffraction was around 45 arcsec. The cutoff wavelength of the fabricated device was ${\sim}10.2{\mu}m$ (0.12 eV) at 80 K while under an applied bias of -1.4 V. The measured activation energy of the device was ~0.128 eV. The dark current density was shown to be $1.0{\times}10^{-2}A/cm^2$ at 80 K and with a bias -1.5 V. The responsivity was 0.58 A/W at $7.5{\mu}m$ at 80 K and with a bias of -1.5 V.

• Journal of the Korean Society of Radiology
• /
• v.12 no.4
• /
• pp.451-457
• /
• 2018

Luminescence properties of $NaCa(PO_3)_3$ doped with $Tb^{3+}$ ions are investigated by optical and laser excitation spectroscopy. The phosphors were prepared by solidstate reaction method The X-ray diffraction(XRD) was used to analyze the crystal structure and the crystallinity of the samples. The excitation and emission spectra and decay curve of $NaCa(PO_3)_3:Tb^{3+}$(0.01 ~ 30mol%) were measured at room temperature. The f - d band of $Tb^{3+}$ is observed in the excitation spectra of $NaCa(PO_3)_3:Tb^{3+}$ in the wave length region 205 ~ 245 nm. Strong emission lines due to the $^5D_4{\rightarrow}^7F_J$ transition and weak emission lines due to the $^5D_4{\rightarrow}^7F_J$ transition are observed in the emission spectra of $NaCa(PO_3)_3:Tb^{3+}$. The energy transfer and cross relaxation between $Tb^{3+}$ ions are discussed in $NaCa(PO_3)_3:Tb^{3+}$ in the emission spectra and life time.

• Journal of Korea Society of Industrial Information Systems
• /
• v.19 no.1
• /
• pp.13-18
• /
• 2014

Sensor nodes are used for monitoring and collecting the environmental data via wireless sensor network. The wireless sensor network with various sensor nodes draws attention as a key technology in ubiquitous computing. Sensor nodes has very small memory capacity and limited power resource. Thus, it is essential to have energy efficient strategy for the sensor nodes. Since the sensor nodes are operating on the same frequency bands with ISM frequency bands, the interference by the devices operating on the ISM band degrades the quality of communication integrity. In this paper, the convolutional code is proposed instead of ARQ for the error control for the sensor network. The proposed convolutional code was implemented and the BER performance is measured. For the fixed transmitting powers of -19.2 dBm and -25dBm, the BER with various communication distances are measured. The packet loss rate and the retransmission rate are calculated from the measured BER. It is shown that the porposed method obtained about 9~12% and 12-19% reduction in retransmission rate for -19.2 dBm and -25 dBm respectively.