• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.22-28
• /
• 1986

기관의 성능에 영향을 주는 인자로서는 외적인자(outside factor), 작동인자(operating factor) 및 설계인자(design factor)의 3가지로 나눌 수 있다. 작동인자로서는 기관회전수, 공기연료비, 점화 시기 또는 분사시기 등이면 설계인자로서는 행정체적, 압축비, 흡배기계통의 구조 및 치수, 냉각 방식 등으로 기관에 따라 고유한 값을 가지는 인자이다. 그러나 외적인자인 대기조건 즉 대기 압력, 대기온도 및 대기습도는 계절, 지역 및 기상조건에 따라 달라지므로 이것에 따라 기관이 흡입하는 공기의 압력, 온도 및 습도는 변화하게 된다. 그러므로 대기조건의 변화에 따라서는 기관작동인자인 공기연료비에도 영향을 미치게 할 것이고 또한 연소상태의 변화로 유효압축비 에도 영향을 미치게 할 것이므로 대기상태의 변화는 곧 바로 기관 출력의 변화를 초래하게 될 것이다. 그러므로 같은 운전조건에서의 기관출력도 대기상태의 변화에 따라 변화하게 되므로 임의의 대기 상태에서 측정한 기관출력을 표준대기상태의 기관출력으로 환산해서 평가할 필요가 생긴다. 이것을 일반으로 출력수정(output correction)이라 하고 있으며 각 나라마다 공업규격 또는 기타규격으로 출력정식을 제정하고 있다. 예를 들면 K.S.B 9102, SAE J816B, B.S. 765, DIN 70020, JIS B 8013등이다. 이들 출력수정식들은 많은 문제점을 가지고 있으므로 종래의 출 력수정식으로 출력수정을 하여도 정확하게 맞지 않은 경우가 많다. 출력수정에 관한 문제는 수 10년전부터 많은 연구자에 의하여 연구되고 거론되어 왔으나 과거의 연구자들이 제안하고 거론 되어 왔으나 과거의 연구자들이 제안하고 있는 출력수정식, 또는 규격으로 정하고 있는 출력수 정방법은 어느 것이나 실용상 만족스러운 것이 아직 없다. 그러므로 본 자료는 스파아크 점화 기관의 흡기습도에 관한 출력수정의 문제를 실험적으로 수행한 실험적 출력수정방법에 의한 것과 종래의 출력수정방법에 의한 것과를 비교 검토하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.77-83
• /
• 2006

A PIV(Particle Image Velocimetry) was applied to measure in-cylinder velocity field according to inlet valve angle during compression stroke. Two engines, one is conventional DOHC 4 valve and the other is narrow valve angle, were used to compare real compression flow. The results show that the flow patterns are well arranged compared with intake flow and the basic tumble flow structures are maintained until end compression stage regardless of valve angle. Also the results show that the tumble motion is intensified by momentum conservation during compression in normal engine. In the normal engine, the bulk shape of flow pattern is "Y" type at the top of cylinder and reverse "Y" type at the bottom of cylinder and weak reverse flow exists at the top of cylinder along cylinder center line. Otherwise, the other engine's flow pattern changes from "Y" type to "T" type at the top of cylinder during compression.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.4
• /
• pp.3970-3979
• /
• 1975

On account of the development of the high speed internal combustion engines, several methods for increasing burning velocity has been investigated lately. Installation of a squash area on a cylinder head is one of the simple and practical method to induce the strong tubulant flow of air-fuel mixtureinto a combustion chamber. In this study, a four-stroke engine used for agricultural purpose was tested as an experimental model. A mathematical model of the squash velocity was derived, and also, several characteristics of the squash phenomena during the motoring of the engine used as a modelwere investigated. The results obtained were as follows: (1) Mathematical model of squash velocity was established and cheked (2) Squaash velocity and engine speed were found to be proportional to the squash area while they were inversely proportional to the squash width. (3) Squash velocity and crank angle at which the squash velocity become its peak were influenced by the magnitude of squash clearance: increase of squash clearance made squash velocity reduced acd made the peak of the squash velocity for from the top dead center and (4) When the squash area is divided in small areas baving unit width along the squash section, squash velocity at each unit width was proportional to the magnitude of the squash distance covered by the unit width.

• Journal of Hydrogen and New Energy
• /
• v.24 no.5
• /
• pp.461-466
• /
• 2013

In this research, the diesel cycle was thermodynamically interpreted to evaluate the possibility of high efficiency by converting diesel engine to the atkinson cycle, and general cycle features were analyzed after comparing these two cycles. That an experimental single cylinder and a long stroke diesel-atkinson engine, of which S/B ratio was more than 3, were manufactured. After evaluating the engine through basic experiments, a diesel engine was converted into the atkinson cycle by constituent VCR (variable compression ratio) device and VVT (variable valve timing) system. The experimental method was to observe compression work reduction effects due to low compression effects from delayed intake valve closing of the early stage atkinson engine. The result, the possibility of increasing compression ratio about each engine load was confirmation by constructing compensate expansion-compression ratio in accordance with the delayed intake valve close.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.1
• /
• pp.104-111
• /
• 2017

A new explosive bellows, which has a diameter of 8.0 mm and a length of 25.4 mm, was developed for a warhead fuze. The new explosive bellows delivers a thrust of 4.5 kgf over a stroke of 25.4 mm. A new gas generator containing BP/MTV ignition charge was also developed and the output test equipment, which measures the length of spring compressed by the function of explosive bellows, was also devised. In order to find out that the new explosive bellows meets the design requirements, the sensitivity tests and output tests were conducted. The test results show that the new explosive bellows meets the requirements and can be applicable to a warhead fuze.

• Journal of the Korean Institute of Gas
• /
• v.24 no.6
• /
• pp.1-10
• /
• 2020

Reactivity controlled compression ignition (RCCI) combustion is one of dual-fuel combustion systems which can be constructed by early diesel injection during the compression stroke to improve premixing between diesel and air. As a result, RCCI combustion promises low nitrogen oxides (NOx) and smoke emissions comparing to those of general dual-fuel combustion. For this combustion system, to meet the intensified emission regulations without emission after-treatment systems, exhaust gas recirculation (EGR) is necessary to reduce combustion temperature with lean premixed mixture condition. However, since EGR is supplied from the front of turbocharger system, intake pressure and the amount of fresh air supplementation are decreased as increasing EGR rate. For this reason, the effect of various EGR rates on the brake power and thermal efficiency of natural gas/diesel RCCI combustion under two different operating conditions in a 6 L compression ignition engine. Varying EGR rate would influence on the combustion characteristic and boosting condition simultaneously. For the 1,200/29 kW and 1,800 rpm/(lower than) 90 kW conditions, NOx and smoke emissions were controlled lower than the emission regulation of 'Tier-4 final' and the maximum in-cylinder pressure was 160 bar for the indurance of engine system. The results showed that under 1,200 rpm/29 kW condition, there were no changes in brake power and thermal efficiency. On the other hand, under 1,800 rpm condition, brake power and thermal efficieny were decreased from 90 to 65 kW and from 37 to 33 % respectively, because of deceasing intake pressure (from 2.3 to 1.8 bar). Therefore, it is better to supply EGR from the rear of compressor, i.e. low pressure EGR (LP-EGR) system, comparing to high pressure EGR (HP-EGR) for the improvement of RCCI power and thermal efficiency.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.7
• /
• pp.953-960
• /
• 2019

The Miller cycle is a diesel engine that has been developed in recent years that it can reduce NOx and improve fuel consumption by reducing the compression ratio through intake valve closing (IVC) time control. The Miller cycle can be divided into the early Miller method of closing the intake valve before the bottom dead center (BDC) and the late Miller method of closing the intake valve after the BDC. At low speeds, the late Miller method is advantageous as it can increase the volumetric efficiency; while at medium and high speeds, the early Miller method is advantageous because of the high internal temperature reduction effect due to the expansion of the intake air during the piston lowering from IVC to BDC. Therefore, in consideration of the ef ects of the early and late Miller methods, it is necessary to adopt the most suitable Miller method for the operating conditions. In this study, a two-stage turbo charge system was applied to four-stroke engines and the process of enhancing the Miller effect through a reduction of the intake and exhaust valve overlap as well as the valve change adjustment mechanism were considered. As a result, the ef ects of fuel consumption and Tmax reduction were confirmed by adopting the Miller cycle with a two-stage supercharge, a reduction of valve overlap, and an increase of suction valve lift.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.10a
• /
• pp.65-70
• /
• 1996

엔진소음을 소음특성에 따라 분류하면 공력소음(Aerodynamic Noise), 연소소음(Combustion Noise), 기계적인 소음(Mechanical Noise)으로 나눌 수 있으며 소음원의 종류에 따라 분류하면 배기계소음(Exhaust System Noise)으로 나눌 수 있으며 소음원의 종류에 따라 분류하면 배기계소음(Exhaust System Noise), 흡기계소음(Intake System Noise), 냉각계소음(Cooling System Noise), 엔진표면소음(Engine System Noise)등으로 분류할 수 있다. 이러한 여러소음중 엔진 내부의 유동에 의한 흡배기계통으로의 소음방출은 자동차 실 내외 소음의 중요한 문제로 대두되는데, 이를 줄이기 위해 그 동안 소음기 등의 서브시스템의 형태와 그 위치조정에 관한 연구가 수행되어 왔다. 그러나 이것이 비용 또는 성능에 영향을 미치므로 본질적인 소음원을 규명해 내는 것이 필요하게 되었다. 흡배기계의 소음은 엔진의 흡입, 배기행 정시 피스톤의 운동에 의해 팽창 및 압축파 형태의 압력파(pressure wave)로 발생하게 되고, 밸브근방에서는 유동의 박리(separation)에 의해 발생하게 된다. 소음기 등의 서브시스템에서도 유동의 박리에 의해 발생하게 되며 특히 배기행정시 발생하는 압력파는 비선형영역에 있게된다. 흡기소음은 배기에 비해 그 크기가 작아서 그동안 등한시 되어왔으나 이것이 소비자의 불평요인으로 작용하므로써 이에 대한 연구도 활발히 수행되어야 한다. Bender, Bramer[1]는 흡배기계 소음의 외부 방사에 관하여 전반적으로 기술하였고 Sierens등[2]은 흡기계에서 1차원 MOC(Method of Characteristics)방법으로 비정상 유동해석을 하고 실험결과와 비교하였다. J.S.Lamancusa 등[3]은 흡기 소음원을 실험을 통해 예측하였고, 흡기소음도 비선형 거동을 보인다고 밝혔다. Yositaka Nishio 등[4]은 새로운 흡기실험장치를 고안하여 공명기(resonator)의 위치 변화에 의한 저소음 흡기계를 설계 초기단계에서부터 적용하려 하였다. 일반적으로 흡배기계의 복잡한 형상 때문에 대부분 실험을 통해 문제를 해결하려 하였고, 수치해석은 피스톤의 운동을 배제한 단순화한 흡배기계의 정상상태 유동해석이 주를 이루어왔다. Taghaui and Dupont 등[5]은 KIVA코드를 사용하여 흡기포트와 연소실 그리고 밸브의 움직임을 동시에 고려한 수치해석을 도입하였다. 하지만 이들이 밸브의 운동을 고려하기 위해 사용한 이동격자는 격자점은 시간에 따라 변화하지만 그 격자의 수가 일정하게 유지되어 있어서 밸브의 완전개폐를 해석할 수가 없다. 강희정[6]은 단일 실린더와 단일 배기밸브를 갖는 문제로 단순화하여 피스톤과 밸브의 움직임을 고려하므로써 배기행정 후 소음이 어떻게 전파해 나가는가를 연구하였다. 본 연구에서도 최소밸브간격과 최대밸브간격 사이에서만 계산이 가능하나 흡기의 경우는 밸브가 닫힐 때 생기는 압력파가 중요하므로 실린더와 밸브사이에 벽면조건을 주어 밸브의 개폐를 모사하였다.

• The Korean Journal of Archival Studies
• /
• no.13
• /
• pp.3-40
• /
• 2006

The archives and records management 'reform' has spreaded out through the third quarter of 2004. There are many evidences such as the change of the Office of the President's management on the record production, 'the reforming road map for the final draft on the archives and records management.' This method spreads into the Cabinets. So it is improved these rosy conditions was upgraded by the laws and regulations. We also hope that the conditions of the records management to be a higher level than before. However the actual conditions of the records management are not good comparing with the law and regulations. I think this unbalance is a serious problem. The reason of the 'failed history' during past time was caused not by the laws itself but by the indifference and negligence on the laws. The academic field and NGO have continuously required some essential suggestions on that problem; political neutrality and independent of the National Archives, the employment of specialists and the improvement of their skills etc. But these requirements have not accepted yet. This revised records management law also has not applied to the road map wholly. Even though the outward growth during that time is remarkable, we need to learn some instructions by way of the 'failed history'. Therefore our urgent task is to narrow the gap between the new system and the actual conditions based on long and short term projects.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.14 no.1
• /
• pp.83-87
• /
• 2008

We have a lot of interest in alternative fuels to provide energy independence from oil producing country and to reduce exhaust emissions for air pollution prevention. Biodiesel, which can be generated from natural renewable sources such as new or used vegetable oils or animal fats, may be used as fuel without change of engine structure in diesel engine of compression ignition engine. In this paper, the test results on specific fuel consumption and exhaust emissions of neat diesel oil and biodiesel blends(10 vol.% biodiesel and 20 vol.% biodiesel) were presented using four stroke, direct injection diesel engine. Especially this biodisel was produced from rape oil at our laboratory by ourselves. This study showed that specific fuel consumption and NOx emission were slightly increased, on the other hand CO emission and Soot were tolerably decreased more in the case of biodiesel blends than neat diesel oil.