• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.41-50
• /
• 2011

It is well-known that pavement is easily damaged by several factors including permanent deformation and fatigue crack, causing service life of the pavement to be shorter than expected. It is very important to predict amount of permanent deformation for designing pavement and developing design method of pavement. A new model of permanent deformation of pavement materials based on concept of shear stress ratio has been proposed because the lower pavement materials are highly affected by shear strength of the material. In this study a large repetitive triaxial load test has been adapted for performing test of permanent deformation of crushed subbase materials. The test procedure which includes concept of shear stress ratio has been newly developed. Several important model parameters can be obtained from the test that can be used for making correct permanent deformation model of the material.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.157-160
• /
• 2008

The confined concrete subjected multi-axil stresses have been known as the strength of concrete increases significantly. Many researchers have studied in confining effect of concrete, and now are studying in many fields. Lap splices were located in the plastic hinge region of most bridge piers that were constructed before the adoption of the seismic design provision of Korea Highway Design Specification on 1992. But sudden brittle failure of lap splices may occur under loading. This study introduces a new method to retrofit RC bridge columns with lap splice which do not have enough ductility during an earthquake. The new method use mechanical external pressure and steel plates around RC columns. The jacketing built following the new method shows good results of increasing the compressive strength and ductility of concrete cylinders. The thicker steel jacket shows larger compressive strength, however, the ductility at failure depends on the welding quality of steel jackets. In this study, The effect of the new method is verified through comparing the results of the compressive tests and analysis results.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.4
• /
• pp.353-367
• /
• 2003

This paper describes the extension of the numerical model, which was developed to simulate the nonlinear behavior of reinforced concrete (RC) structures subjected to monotonic in plane shear and introduced in the companion paper, to simulate effectively the behavior of RE structures under cyclic loadings. While maintaining all the basic assumptions adopted in defining the constitutive relations of concrete under monotonic loadings, a hysteretic stress strain relation of concrete, which across the tension compression region, is defined. In addition, unlike previous simplified stress strain relations, curved unloading and reloading branches inferred from the stress strain relation of steel considering the Bauschinger effect we used. The modifications of the stress strain relation of steel are also introduced to reflect pinching effect depending on the shear span ratio and an average stress distribution in a cracked RC element. Finally, correlation studies between analytical results and experimental studies are conducted to establish the validity of the proposed model.

• Computational Structural Engineering
• /
• v.8 no.2
• /
• pp.115-121
• /
• 1995

The object of this study is to propose a rational method of resistance strength and flexural deformation for structures using high strength concrete(400-700kgf/cm/sup 2/). The material property(stress-strain relationship) is to be modelize using regression analysis of experimental result. And the applicability of trapezoidal stress model is to be verified. An analytical method is used by the moment-curvature relationship which is based on stress-strain relationships of material for discreted element of section. The evaluation method of moment-curvature of high strength concrete structures is also proposed by using the Monte Carlo Simulation based on a probabilistic concept that could minimize an error due to iterated calculations and random variable of material properties.

• Geotechnical Engineering
• /
• v.8 no.2
• /
• pp.45-58
• /
• 1992

An elasto-plastic constitutive model for geological materials, which satisfies the flezibility and stability at the same time, can be used in a number of geotechnical problems. Using the spacing ratio of critical state, a flexible model is proposed based on the stability of modified Camflay model. The spacing ratio of critical state can be simply evaluated, and practically used in describing the undrained shearing behavior of clay. The proposed model has precisely predicted the stress paths and stress -strain relationships, compared with the modified Camflay model, with respect to undrained triaxial test results. Besides, the effects of strain rate, creep, and relaxation can also be considered. Using the quasi-state boundary surface, the constitutive relations are well predicted. Therefore, it is found that the assumption of associative flow rule is well posed for undrained behavior of normally consolidated clay.

• The Korean Journal of Rheology
• /
• v.11 no.1
• /
• pp.18-27
• /
• 1999

Predicting the deformation behaviors of sheets in thermoforming processes has been a daunting challenge due to the strong nonlinearities arising from very large deformations, mold-polymer contact condition and hyperelasticity constitutive equations. Nonlinear numerical analysis is always required to face this challenge especially for realistic processing conditions. In this study a 3-D algorithm and the membrane approximation are developed for thermoforming processes. The constitutive equation is expressed in terms of the 2nd Piola-Kirchhoff stress tensor and the Cauchy-Green deformation tensor. The 2-term Mooney-Rivlin model is used for the material model equation. The algorithm is established by the finite element formulation employing the total Lagrangian coordinate. The deformation behavior and the stress distribution results of 3-D algorithm with various point boundary conditions are compared to those of the membrane approximation algorithm. Also, the slip boundary condition and the no-slip boundary condition are applied for the systems that have molds. Finally, the effect of sheet temperatures on the final thickness distribution is investigated for the ABS material.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.101-110
• /
• 2014

Expansion agent is a very effective admixture for prevention of cracking due to autogenous/drying shrinkage and this can induce internal chemical prestress to embedded reinforcement. In this paper, tension-softening and hardening in cement mortar with steel and CSA expansion agent are experimentally evaluated. Cement mortar with steel reinforcement is prepared and tensile strength test is performed for evaluation of cracking and tensile behavior. In spite of slightly reduced strength and elasticity in CSA mortar, significantly increased tension-hardening behavior is evaluated in CSA mortar with induced chemical prestress. Furthermore previous tension softening models are compared with the test results and improvement are proposed.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.3
• /
• pp.321-329
• /
• 2003

To effectively use the cross section of concrete decks, analytical and experimental studies on prestressed steel-box-girder bridges were performed in this study. The method of applying prestress was determined in the analytical study and the longitudinal behavior of the prestressed steel-box-girder bridge was considered in the experimental study. The object model for these studies was a two-span continuous bridge. The method of applying prestress determined herein was divided into two parts: one is that apply prestress to the concrete deck at its intermediate support, and the other is that apply prestress to the lower flange of the steel-box-girder bridge at its end support. The prototype bridge for the experiment was simulated based on the rule of similitude and was fabricated according to construction steps to apply prestress effectively. From the results of the experimental study, it has demonstrated that the prestressed steel-box-girder bridge provides better performance than the general steel-box-girder bridge in view of the increase of the design live load, the reduction of the tensile stress of the concrete deck at intermediate support, and the reduction of the displacement.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.2
• /
• pp.103-113
• /
• 2000

기존의 Terzaghi 압밀이론은 상대적으로 연약토층이 두껍지 않고, 초기함수비가 낮으며 적은 유효응력의 증가가 예상되는 곳에 그 적용이 제한되어 있었다. 그 이유는 Therzaghi 압미이론 자체가 미소변형률과 선형적인 압축성 및 투수성등을 기본적인 가정사항으로 내포하고 있기 때문이다. 이러한 가정사항을 극복하고자 Gibson et al. 은 일차원 비선형 유한 변형률 압밀이론에 관한 엄밀해를 제시하였다. 이 이론은 기존의 많은 가정사항들을 극복하여 실제 현상에 더욱 부합하는 예측을 할 수 있는 장점이 있는 반면, 비선형적인 응력-변형 관계, 변형-투수계수 관계의 도입과 좌표변환 및 현장의 시고이력을 그대로 적용하는데 많은 어려움이 있는 것이 사실이다. 본 연구에서는 이러한 비선형 유한형태를 압밀이론을 이용한 압밀현상 예측을 위하여, 비선형적인 응력-변형 관계, 변형-투수계수 관계에 관한 함수식을 구성하고 이를 포함하는 컴퓨터 프로그램을 개발하였다. 개발 프로그램은 많은 폼과 모듈로 구성되어 있는데, 이러한 각각의 폼과 모듈은 GUI 기능의 극대화를 통해 복잡한 이론에 익숙하지 않은 실무자들이 쉽게 본 이론을 이용할 수 있도록 설계 되었다. 또한 개발프로그램은 다양한 하중단계 및 비선형적인 응력-변형 관계, 변형-투수계수 관계에 관한 회귀분석, 각 유효응력 단계별 상이한 비선형 계수 g와 λ를 적용할 수 있으며, 계산을 위한 전처리과정은 물론 계산된 결과를 위한 다양한 후처리과정이 모두 사용자 위주의 GUI 기능을 충분히 갖도록 설계되었다. 개발 프로그램의 검증을 위하여 실제 현장의 계측자료 및 기존 연구문헌상의 결과와 본 개발 프로그램의 예측결과를 비교.분석하였으며, 다양한 간극비 상태의 비선형 계수가 해석결과에 미치는 영향을 알아보았다.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.3 s.32
• /
• pp.421-430
• /
• 1997

In this study, the static and the fatigue tests were performed with high tension bolted joints, of which the surfaces were spread with inorganic zinc-primer after shot-blast, and milling surface, and steel-natural surface, difference of friction surface condition were examined by comparing the esults of tests. From the result of synthetical investigation of this study. it is proper that using the torque management method in order to introduce design axial force to blots, and the provision of specifications that initial axial forces must be 110% of design axial forces is proper. Decreasing ratio of axial forces to initial force is proportional to common lorgarithms of time progress, it converge constant value after 20 hours, and decreasing ratio is little related to the roughness of friction surface. Sliding coefficient of milling, spreading inorganic zinc-primer, just producting is great in order and sliding forces are dependent on the applied axial forces, but if the applied axial forces are great, sliding coefficient become small by a loss of roughness. So it is confirmed that relation between the applied axial forces and the sliding forces are not proportional linearly. From the result of estimation on fatigue strength, all specimens satisfy the specifications with B-grade and milling surface is lower than the others about 14% in fatigue strength because in milling surface lose the function of friction-types joints at lower number of cycles. From the result of eximination for the distribution area of compressive force, friction area near to inside bolt is wider in the direction of stress than near to outside. It is guessed that this situation occurs because outside bolts firstly change from the friction connection to the bearing connection.