• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.333-334
• /
• 1989

Electrically active part of the piezoelectric sound element is a ceramic thin circular disk cemented to a metal base plate (using a type of thermosetting epoxy). The active part is a thin lead zirconate titanate disk (PZT). The piezoelectric sound element is so dimensioned that its basic resonance frequency is approximately if the center of the audible frequency band: This frequency is mainly determined by the geometry and the sort of the metal base plate materials. In this study, four kinds of PZT ceramic and two classes of thin metal base plate were prepared. It is observed that dielectric and pizoelectric properties relate to acoustical properties (particularly sound pressure level).

• Electrical & Electronic Materials
• /
• v.8 no.1
• /
• pp.1-5
• /
• 1995

In this study, a piezoelectric fan was fabricated using piezoelectric element of 0.13PZN-0.41PZ-0.46PT prepared by extruding method. The sizes of the piezoelectric element and the piezoelectric fan were adjust to utilize commercial ac source(100V, 6OHz). The size of the piezoelectric element was $0.26{\times}19.5{\times}45$mm and the resonant frequency and the electromechanical coupling coefficient were 31.26KHz, 31.58% respectively. The size of the piezoelectric fan was $0.62{\times}19.5{\times}78.5$mm and the maximum displacement was 40mm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.7
• /
• pp.597-601
• /
• 2002

In this study, the structural, dielectric and piezoelectric properties of $Pb[(Ni_{1/3}Nb_{2/3})_x-(Mn_{1/3}Nb_{2/3})_{0.09-x}-(Zn_{0.505}Ti_{0.495)_0.91]O_3$ (x=0, 0.01, 0.02, 0.03, 0.04, 0.05) system ceramics were investigated to develop the composition ceramics for piezoelectric transformer. All the specimens were sintered at $1250^{\circ}C$ and its physical properties were measured, and the results are as follows : With increasing PNN substitution for PMN-PZT system, dielectric constant was increased and electro-mechanical coupling factor($k_p$) was increased to 0.62 at 5 mol% while mechanical quality factor(Qm) was decreased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.109-114
• /
• 2002

Aging stabilities of the operating frequency of piezoelectric devices such as filter, oscillator and discriminator are very important. In this study it was studied aging stabilities of the length-extensional vibration mode of Pb(Zr$\_$y/Ti$\_$1-y/)O$_3$+x[wt%]Cr$_2$O$_3$ ceramics. PZT ceramics in Morphotropic phase boundary have higher aging rates of k$\_$31/ and resonant frequency than those in tetragonal phase or rhombohedral phase. Thermal aging moves the composition with maximum aging rate to Zr-rich side in Cr not added PZT system. Aging rate of resonant frequency of the ceramics with x=0.1, y=0.53 and x=0.3, y=0.53 increased by thermal aging.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.287-290
• /
• 2000

본 연구에서는 압전세라믹스와 금속판으로 구성된 음향트랜스듀서를 모델로 설정하고, 원형평판으로부터 방사되는 내부음장과 트랜스듀서의 외부로 방사되는 음향특성을 수치 해석하였다. 음향트랜스듀서의 내부 유니트를 요소 분할하며 경계조건을 적용시키고, 유한요소법을 이용하여 내부의 음장 분포와 음압 변화량을 가시화하였다. 그리고 트랜스듀서 외부로 방사되는 음압은 가상경계면 외부를 요소분할한 후 다양한 주파수에서 음압 기울기와 등압선을 수치해석하였다.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.1030-1036
• /
• 1994

The ceramics in the system 0.5[Pb(Ni1/3Nb2/3)O3]-0.5[0.65PbTiO3-0.35PbZrO3] were prepared by conventional solid state reaction method, double calcined method (columbite precursor method) and flux method using NaCl-KCl. Amount of pyrochlore phase for the calcined powders, sintering charateristrics, dielectric and piezoelectric properties were then investigated. Sintering temperature was 1000~120$0^{\circ}C$ and in case of flux method, the amount of flux to oxide was 1 : 1 mole ratio. The dielectric and piezoelectric properties of ceramics prepared by double calcined method and flux method were found to be better than those by conventional method. It was also possible to lower sintering temperature and reduce the amount of pyrochlore phase either by double calcined method or flux method. But with increasing sintering temperature, the difference in characteristrics due to diffrent fabrication method gradually.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.1
• /
• pp.50-55
• /
• 1992

Piezoelectric Buzzer which has been generally used requires about 30kV/cm poling process and has the aging effects. In this study, 0.85 PZN - 0.10 BT - 0.05 PT system ceramics with additives of 0 - 2 wt% YS12TOS13T were fabricated and investigated on electromechanical coupling coefficient(kS1pT), electric field induced charge coefficient(dS131T), and sound level. As the results, in the 0.4 wt% YS12TOS13T added composition ceramics compared with the basic, kS1pT was increased from 0.355 to 0.39 and induced piezoelectric d constant increased from 204 to 220 x 10S0-12T (C/N) and sound level of electrostrictive Buzzer has the highest value of 71.5 dB under 8kV/cm bias electric field.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.6
• /
• pp.687-693
• /
• 1992

To improve dielectric, piezoelectric and temperature stability in 0.50Pb(SnS11/2TSbS11/2T)OS13T - 0.35PbTiOS13T - 0.60PbZrOS13T + 0.4[wt%]MnOS12T piezoelectric ceramics which is used for surface acoustic wave devices, CrS12TOS13T was added and the specimens were fabricated by Hot Press method, and their characteristics were measured with CrS12TOS13T addition. From the results, in the specimen added by 0.2[wt%]CrS12TOS13T, dielectric constant and mechanical quality factor were 380 and 2307, respectively, and it was suited for surface acoustic wave device and the temperature coefficient of the resonant frequency in the specimen added by 0.4[wt%]CrS12TOS13T was the least value of 74.96[ppm/$^{\circ}C$].

• Electrical & Electronic Materials
• /
• v.10 no.1
• /
• pp.20-25
• /
• 1997

In this study, piezoelectric actuator samples were fabricated using 0.375PMN-0.37OPT-0.255PZ system ceramics with Barium substitution and the strain properties of them were investigated. Dielectric constant of the specimens increased with the increase of Ba content up to 5mol% and decreased with futher addition of Ba. The largest piezoelectric coefficient and electromechanical coupling coefficient were observed at the sintering temperature of 1250'C and Barium content of 5mol%. The characteristics of strain hysteresis was found largely with varing the sintering temperature on the single round type, and the strain is proportional to piezoelectric coefficient.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.238-241
• /
• 2000

In this paper, we manufactured Pb($Ni_{1/2}$ $W_{1/2}$)$O_3$-Pb($Mn_{1/3}$$Nb_{2/3}$)$O_3$-Pb($Zr_3$Ti)$O_3$ceramics with variation of milling time and investigated its dielectric and piezoelectric properties. Density was increased with the increase of milling time because the sinterability of specimens were improved with the decrease of particle size. The highest value of electromechanical coupling factor was 0.518 at milling time 5hour. The highest values of mechanical quality factor and dielectric constant were 1566, 1590 at milling time 4hour, respectively.