• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1456-1457
• /
• 2008

본 논문에서는 박막 PZT(Pb(Zr,Ti)O3)를 이용한 d33모드의 자가 발전 소자를 설계 및 제작 하였다. 자가 발전 소자는 진동 에너지를 압전 현상을 통해 전기 에너지로 변환하는 소자로서, 제안한 구조는 단일 외팔보가 아닌 20개 이상의 외팔보를 원형으로 집적한 구조를 갖기 때문에, 기존의 단일 외팔보 위주의 자가발전 소자보다 출력 전력이 우수하다. 자가 발전 소자의 성능 최적화를 위해 유한요소기법(FEM)을 통해 기계적 특성을 분석하였으며, 마이크로 머시닝 기법을 이용하여 초박형의 자가 발전 소자를 제작할 수 있었다. 제작된 자가발전 소자는 $1.2mm\times1.2mm\times0.5mm$ (높이)의 크기를 갖는다.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.282-283
• /
• 2007

본 논문에서는 저전압에서 구동 할 수 있는 압전구동 방식의 RF MEMS 스위치를 설계하였다. 설계는 유한요소기법(FEM)을 지원하는 시뮬레이터 (ConventorWare)를 사용하여 수행하였고, 이를 바탕으로 deflection, contact force, stress 등 기계적인 해석을 함으로써 최적화된 설계를 할 수 있었다. 이번 설계에서는 적절한 contact force를 유지하면서 hinge에서 받는 stress를 최소화하기 위하여 구동기를 2개 사용한 듀얼형식의 모델을 제안하였고, hinge의 모양은 'ㄷ'로 하여 deflection을 향상시켰다. 이 듀얼형식의 최적화된 모델은 signal line과 contact pad 간의 gap이 3.4${\mu}m$일 때, 최초 2.8V에서 contact이 이루어졌으며, 5V에서 12.4${\mu}N$의 contact force와 116MPa의 stress를 얻었고, 차후, SP4T나 SP6T 등의 설계시 공간 효율이 높은 다양한 형태의 구조를 설계할 수 있다.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.5
• /
• pp.83-88
• /
• 1995

The common practice for the identification of piezoelectric properties is based on the use of immittance of a resonator with a certain geometry and poling direction. In this paper, a new method is suggested to identify the complex-valued piezoelectric material constants. This method Is based on the minimization of differences between the analytical immittance and the experimental measurement of resonator. Non-linear minimization problems are formulated to find out the unknown properties relevant to the resonators. The immittance data used for identification are measured at a number of frequencies which cover the vicinity of resonance frequency and the low frequency region. To illustrate the proposed technique, the complex-valued coefficients are identified for a typical PZT4 ceramic composition.

• The Journal of the Acoustical Society of Korea
• /
• v.34 no.2
• /
• pp.108-116
• /
• 2015

An acoustic vector sensor is a device that is capable of measuring the direction of wave propagation and the acoustic pressure. In this paper, the modeling of micro-cantilever sensor for the vector sensor are proposed by consideration of acoustic phenomenon in water. Two models based on unimorph structure are proposed in this paper and corresponding transfer function which describes the relation between input pressure wave and output voltage depending on incidence angle and frequency of pressure wave is derived based on lumped model. It has been shown that very thin and flexible micro-cantilever can be used to measure directly the particle velocity component in water.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.10 no.6 s.52
• /
• pp.79-91
• /
• 2006

A new methodology of guided wave based nondestructive testing (NDT) is developed to detect crack damage in civil infrastructures such as steel bridges without using prior baseline data. In conventional guided wave based techniques, damage is often identified by comparing the "current" data obtained from a potentially damaged condition of a structure with the "past" baseline data collected at the pristine condition of the structure. However, it has been reported that this type of pattern comparison with the baseline data can lead to increased false alarms due to its susceptibility to varying operational and environmental conditions of the structure. To develop a more robust damage diagnosis technique, a new concept of NDT is conceived so that cracks can be detected without direct comparison with previously obtained baseline data. The proposed NDT technique utilizes the polarization characteristics of the piezoelectric wafers attached on the both sides of the thin metal structure. Crack formation creates Lamb wave mode conversion due to a sudden change in the thickness of the structure. Then, the proposed technique instantly detects the appearance of the crack by extracting this mode conversion from the measured Lamb waves even at the presence of changing operational and environmental conditions. Numerical and experimental results are presented to demonstrate the applicability of the proposed technique to crack detection.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.10
• /
• pp.777-784
• /
• 2003

Acoustic response control of a corner-pinned plate using piezoelectric wafers was studied, both theoretically and experimentally Three different sizes of aluminum alloy plates were used and available ball joints were employed to hold the plate at the four corners. The plate with the largest aspect ratio showed the largest and most clear responses to the acoustic excitation in the range of frequencies (0∼200 Hz), and sound pressure levels (80∼100 dB) as predicted. The reduction of the acoustic response of the plate by piezoelectric actuator was very significant, more than expected, but abatement of the sound transmission through the plate was only slightly altered by the piezoelectric actuator. This work is an original work extending earlier work with doors excited by acoustic fields. The important difference is the used of ball joints to simulate the joints.

• Composites Research
• /
• v.31 no.4
• /
• pp.145-150
• /
• 2018

Various structural health monitoring (SHM) systems have been suggested for aerospace industry in order to increase its life-cycle and economic efficiency. In the case of aircraft structure madden with metal, a major concern was hot spots, such as notches, bolts holes, and where corrosion or stress concentration occurs due to moisture or salinity. However, with the increasing use of composites in the aerospace industry, further advanced SHM systems have been being required to be applied to composite structures, which have much complex damage mechanism. In this paper, a method of acoustic emission localization for composite structures using Q-switched laser and multiple Amplifier-integrated PZTs have been proposed. The presented technique aims at localization of the AE with an error in distance of less than 10 mm. Acoustic emission simulation and the localization attempt were conducted in the composite structure to validate the suggested method. Localization results, which are coordinates of detected regions, grid plots and color intensity map have been presented together to show reliability of the method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.11a
• /
• pp.241-242
• /
• 2007

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.143-144
• /
• 2008

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.491-492
• /
• 2010