• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.122-126
• /
• 2006

Two types of pressurization system and low weight feeding piping system are developed. With sub-system tests, ullage pressure control performance was verified for 1 step and 2 step pressurization system and the feeding performance of feeding piping system was also verified. The weight of the feeding piping system is low enough for the application of launch vehicle. In addition, LOX conditioning system is developed for avoiding geysering and LOX temperature rise. Integrated performance was verified through integrated on-board feeding system performance tests.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.2
• /
• pp.243-249
• /
• 2010

The improvement of fuel economy and the reduction of diesel exhaust PM(Particulate Matter) and $NO_X$ have been successfully achieved by supplying diesel engines with emulsified diesel oil. However, combustion analysis of emulsified C-heavy oil is difficult because the combustion characteristics of emulsified C-heavy oil compared to other fuels have a special form. Therefore, these experimental researches have analyzed the combustion characteristics of emulsified C-heavy oil in a chamber with high pressure and temperature. The pressure and the rate of heat releases in a combustion chamber was decreased with increasing the water content and the ignition delay time was increased with increasing the water percent.

• Journal of Power System Engineering
• /
• v.3 no.2
• /
• pp.26-33
• /
• 1999

Pressure pulsation Inside the discharge and suction cavity of rotary and scroll compressor are often a major source of objectionable noise and vibration. The key factor of these noise and vibration is due to the cavity resonance. It is not only necessary to understanding the characteristics of pulsation in order to reduce the excitation force of gas to the cavity but also to verifying the phenomena of cavity resonance. For the purpose of these understandings, measurement and simulation of cavity resonance can lead to a better understandings how they occur and be very important to identify the ways to reduce the noise efficiently. In this paper, modeling of the cavity(internal acoustics inside the shell) is discussed and simulated using FEM. Results from the simulation are compared with those measurement in experiments. In describing of cavity mode by experiments, it is very important to specify the exact conditions under which they are measured. Finally, this paper shows the one example of reduced cavity resonance in the compressor.

• Journal of the Korean Society for Railway
• /
• v.13 no.5
• /
• pp.516-520
• /
• 2010

Parametric study has been conducted to calculate the capacity of vacuum pump system that will be used to maintain the pressure of the tube structure under atmosphere level. Recently many railroad researchers pay attention to the tube train system as one of the super high speed transportation system. To achieve the super high speed, the inside of tube system should be maintained at low pressure level. In the low pressure environment, it is well known that air resistance of train is drastically decreased. Vacuum pump system will be used to make low pressure state for tube structure, exhaust the leakage air and supplement additional vacuum pumping. As results of these studies, we get the lump capacity of vacuum pump for various parameters. These results can be applied to analyze the effects of the reduction of air resistance.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.27 no.3
• /
• pp.152-157
• /
• 2015

Stack effect on high-rise building have negative effect on living environment, energy and life-safety aspect. Thus, it's necessary to find the measure to reduce the stack effect. As a result of field test on a 31-story building, a circulating type stack effect reduction technology was developed, which supplies air in the low stairs and discharges air in the high stairs. To evaluate the performance of this circulating type stack effect reduction technology on building stairs, a 3D numerical analysis was carried out by using Momentum Loss Model for analyzing leakage flow between compartments in a building. Consequently, numerical analysis proved that the stack effect on building stairs was reduced by a circulating type stack effect reduction technology.

• Journal of Energy Engineering
• /
• v.12 no.2
• /
• pp.124-130
• /
• 2003

In the present study, the combustion characteristics of methane and hydrogen-supplemented methane as alternative fuels for automotive vehicles were investigated at various hydrogen substitution rate, ignition position and ignition methods in a CVCC. As a result, it is possible to decrease the total burning time and to obtain the reduction of NO concentration by using MSCDI device under the lean mixture conditions without deteriorating combustion characteristics such as combustion efficiency, maximum combustion pressure etc.. And by mixing hydrogen into methane, it was found that the reduction of the total burning time was obtained, in comparison with the use of methane only ; and at the same time, the combustion promotion rate was improved remarkably in comparison with the use of methane only.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2011.10a
• /
• pp.44-44
• /
• 2011

디젤 엔진 배기가스 중의 황산화물(SOx)은 산성비의 원인이 될 뿐 아니라 인체에 대해서도 상당히 치명적인 위험을 초래하는 성분으로 지금까지는 다른 오염물질인 질소산화물 (NOx), 입자상 물질(particulate matter) 등에 비해서 상대적으로 덜 주목을 받아왔다. 국제적인 황산화물 배출규제의 경우, '황산화물 배출규제지역' (SECA : SOx Emission Control Area)에 대해 엄격한 배출규제가 시행되고 있는데, 대부분 황함량을 1.5%이하의 연료를 사용하거나, 후처리 설비를 설치해서 배기가스 중의 황산화물을 6.0g/kWh 이하로 유지하도록 규정하고 있다. 따라서 본 연구에서는 강화되고 있는 디젤엔진 배기가스 중의 황산화물과 입자상 물질을 저감하기 위한 설비로서, 높은 경제성 및 신뢰성 등의 장점으로 인해 선정 가능성이 가장 높은 스크러버 시스템에 대해 독자모델 설계를 수행하였으며 파일롯 설비를 활용한 실제 디젤엔진에 대한 실험을 통하여 운전조건에 따른 제거효율, 발생되는 처리수의 성분, 그리고 디젤엔진 운전에 영향을 미치는 압력손실 등에 대한 데이터를 확보함으로써 실제 선박적용에 대한 가능성을 확인하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.98.2-98.2
• /
• 2011

지구 온난화의 원인이 되는 이산화탄소를 저감하며 유해한 배기가스를 배출하지 않는 수소연료전지자동차(FCV)에 대한 관심이 높아지고 있다. 한국가스안전공사에서 현재 구축하고 있는 평가장비는 이러한 수소연료전지자동차용으로 사용되는 고압용기의 수압반복시험 및 밸브류로 구성된 고압수소저장시스템의 단품 및 시스템 평가를 통한 안전신뢰성 검증을 목적으로 하고 있다. 현재 수소연료전지자동차는 차량이나 부품의 시험 방법에 대한 통일된 기준/표준/시험법이 아직 완전하게 정비되어 있지 않고, 시장에서의 도입 제도, 기준 등이 만들어지고 있는 현실이다. 또한 연료로 수소를 사용하는 도입단계에 있기 때문에, 수소용기가 반복압력변동에 따라 어떤 거동을 나타내는지에 대한 실험관련 연구가 미진한 상태이다. 따라서 수소연료전지자동차용 고압수소저장시스템에 대한 내구성, 안전성 확보를 위하여 수소연료전지자동차에서 중요한 부품인 용기에 대한 반복피로시험이 필요하다. 특히 복합재 용기 분야에서 Type3용기에 대한 높은 안전성과 내구성이 보고되고 있지만 실질적으로 얼마나 다른 용기에 비해 높은 성능을 가지고 있는지 국내에서는 체계적으로 검증된바 없다. 따라서 구축된 수압반복 장비를 이용하여 Type3 용기에 대한 수압반복시험을 실시하였으며, 이를 통해 수소용기의 거동을 확인하고자 한다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.6
• /
• pp.62-72
• /
• 2012

Divert and attitude control system(DACS) plays an important role for orbit transfer and attitude control, and therefore becomes important subject for recent space vehicle and Precision Guided Missile(PGM) development. To develop DACS system, main research areas include shape combination of pintle and nozzle to maximize thrust change, and reduction of aerodynamic pintle load to minimizle pintle driving force, and development of multi-axis control algorithm. In this paper, introduction, classification, and overseas/domestic research and development program, and prospects of DACS are reviewed and summarized.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.430-435
• /
• 2008

Total lengths of domestic pipe network for district heating system are above about 2,500Km. A lots of pumping power for heat transportation through long pipe are required by the flow friction of pipe surface. Until now there have been considered about various methods to reduce the flow friction for district heating system such as using surfactants and turbulence promoters by swirl flow and baffles etc. At this study, swirl flow generator was tested about the possibility to increase the heat transfer ratio at the heat exchanger in the case which the suppling water temperature increased from $50^{\circ}C$ until $120^{\circ}C$. Experimental results showed that the heat transfer ratio increased and also pressure increase ratio increased simultaneously in the case which swirl flow generator installed. The amount of the increasing ratio for heat transfer and pressure were reached until 4.33% and 11% at the case of $120^{\circ}C$ suppling temperature which domestic district heating system were using.