• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.591-596
• /
• 2016

Numerical analyses were performed on the heat flow characteristics of a heat transfer plate with six different shapes (basic, rectangle, triangle, wave type) to reduce the level of white smoke at a stack. In this study, to examine the heat transfer performance (heat transfer capacity, pressure drop, turbulence kinetic energy, heat transfer coefficient) on the heat transfer plates, simulations were conducted using the commercial computational fluid dynamics software, ANSYS CFX Ver.14 under uniform flow conditions. The thermal flow phenomenon in a channel with six heat transfer plates could be predicted adequately under uniform flow conditions. The heat transfer capacity, pressure drop, turbulence kinetic energy, and heat transfer coefficient were affected by the flow rate, aspect ratio and plate shape. These results provide guidelines to design an effective heat exchanger with the wave type to reduce white smoke.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.381-384
• /
• 2011

Wave drag reduction due to the repetitive laser induced energy deposition over a flat-nosed cylinder is experimentally conducted in this study. Irradiated laser pulses are focused by a convex lens installed in side of the in-draft wind tunnel of Mach 1.94. The maximum frequency of the energy deposition is limited up to 80. Time-averaged drag force is measured using a low friction piston which was backed by a load cell in a cavity as a controlled pressure. Stagnation pressure history, which is measured at the nose of the model, is synchronized with corresponding sequential schlieren images. With cylinder model, amount of drag reduction is linearly increased with input laser power. The power gain only depends upon the pulse energy. A drag reduction about 21% which corresponds to power gain of energy deposition of approximately 10 was obtained.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.3
• /
• pp.295-302
• /
• 2014

An internal gear pump is required to improve the flow rate and noise. Furthermore, such pumps are durable and small in size. In this study, equations of the rotor shape with multiple profiles (ellipse 1-involute-ellipse 2) were derived, and relevant performance parameters (pressure angle, irregularity, and specific sliding) of the internal gear pump to noise were predicted and compared. Rotor profiles and performance parameters were obtained by a prediction algorithm for theoretical analysis, and the effects between the design parameters and the performance parameters were analyzed. Based on the analysis results of the effects, an optimal design of the rotor profile was proposed, and a noise test of the prototype was performed to evaluate the reliability of the design.

• Journal of the Korea Convergence Society
• /
• v.9 no.4
• /
• pp.161-167
• /
• 2018

The amount of CNG was measured using a pressure sensor in the case of CNG vehicles. However, the current measurement method causes anxiety to the driver because it is difficult to measure the detailed amount of CNG according to various environmental conditions. This study was performed to measure the amount of CNG in CNG fuel system, and presented the method of measurement by simulating the detection system of CNG. In this experiment, a detection simulator with an ultrasonic sensor in CNG tank of Type-3 was designed, and the reception signal of the ultrasonic sensor was verified by reducing the pressure from 100 bars to 0 bars (increment=5 bars) using compressed air. As a result, the output signal voltage of the ultrasonic sensor decreased as the pressure in the tank decreased, and the it was verified that the shape of the graph was linearity.

• Journal of the Korean Institute of Gas
• /
• v.18 no.2
• /
• pp.21-27
• /
• 2014

A MILD(Moderate and Intense Low oxygen Dilution) combustion, which is effective in the reduction of NOx, is considerably affected by the recirculation flow rate of hot exhaust gas to the combustion furnace. The present study used a coanda nozzle for the exhaust gas recirculation in a MILD combustor. A numerical analysis was accomplished to elucidate the effect of exhaust gas entrainment toward the furnace with or without a coaxial contractor. The result of the present CFD analysis showed that the entrainment mass flow rate without a coaxial contractor had 18% larger than that with a coaxial contractor when the mixed gas outlet pressure was ambient pressure. On the other hand, if the outlet pressure increased, the mass flow rate with a contractor was larger than that without a contractor. It could be analysed by the entrainment driving force composed with the nozzle throat pressure, inlet and outlet pressures and flow cross sectional area.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.5
• /
• pp.449-456
• /
• 2010

The HCCI engine is a prospective internal combustion engine with which high diesel-like efficiencies and very low NOx and particulate emissions can be achieved. However, several technical issues must be resolved before HCCI engines can be used for different applications. One of the issues concerning the HCCI engine is that the operating range of this engine is limited by the rapid pressure rise caused by the release of excessive heat. This heat release is because of the self-accelerated combustion reaction occurring in the engine and the resulting engine knock in the high-load region. The purpose of this study is to evaluate the role of thermal stratification and fuel stratification in reducing the pressure rise rate in an HCCI engine. The concentrations of NOx and CO in the exhaust gas are also evaluated to confirm combustion completeness and NOx emission. The computation is carried out with the help of a multizone code, by using the information on the detailed chemical kinetics and the effect of thermal and fuel stratification on the onset of ignition and rate of combustion. The engine is fueled with dimethyl ether (DME), which allows heat release to occur in two stages, as opposed to methane, which allows for heat release in a single stage.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.7
• /
• pp.823-828
• /
• 2012

The soft recoil mechanism was an effective mechanism for reducing the recoil force by forwarding momentum. There were some parameters such as the fire angle, firing position, and initial pressure of the recuperator, which influenced the forwarding momentum. These parameters affected the generation of the forwarding momentum in the soft recoil mechanism. To design for the mechanism, the parameters affecting momentum were studied to consider some reasonable conditions. Among the various parameters, the initial pressure of the recuperator and firing position was confirmed as a key factor to have affected the momentum. It was determined that the recoil force had a minimum value when the initial pressure of the recuperator was 180.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.5
• /
• pp.1262-1275
• /
• 1993

The drag reduction effect of a freely-rotatable splitter plate was experimentally investigated in the 2-D wake behind a circular cylinder. By arranging the splitter plate to be aparted with a certain gap from the cylinder, the splitter plate was able to be aligned itself automatically to the flow direction in the tested range of 6.2$\times$$10^3$$\times$$10^4$. As a result, it was proven that the self-adjustable splitter plate always reduced effectively the drag imposed on the body against any arbitrary flow directions. In a specific range of Reynolds numbers, the drag reduction effect was dependent not only on the length of the splitter plate but also on the gap distance between the plate and the trailing edge of the body. For a splitter plate with a specific length, there existed a unique optimum range of gap distance to obtain successfully the drag reduction effect, however, the optimum range of gap distance was dependent on Reynolds number.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.6
• /
• pp.546-555
• /
• 2001

In this paper filtering techniques to reduce the adverse effects of motor leads on high-frequency PWM inverter fed AC motor drives are presented. The filter was designed to keep the motor terminal from the cable surge impedance to reduce overvoltage reflections ringing and the dv/dt, di/dt, at the motor terminals. Specially the output filter is used to limit the rate of the inverter output voltage and reduce common mode noise to the motor, The performance of the output filter is evaluated through simulations and experiment on PWM inverter-fed AC motor drive. An experimental PWM drive system reduction of conducted EMI was implemented on an available TMS320C31 microprocessor control board Finally, experimental result shows inverter output filter reduces more common mode voltage than low pass filter also reduce overoltage and ringing at the motor terminal.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2011.10a
• /
• pp.41-41
• /
• 2011

국제해사기구(IMO)에서2016년에 건조되는 선박부터 Tier III 규제를 예고하고 있다. 이 규 제를 만족하기 위하여 엔진 전처리 기술 및 후처리 기술 개발과 실증 연구가 활발히 진행되고 있다. 이중 SCR(Selective Catalytic Reduction) 반응을 이용한 질소산화물 저감기술이 80% 이상의 Tier III NOx 규제치를 만족할 수 있는 유일한 기술이다. 육상 플랜트에서 실증과 검증이 확보된 SCR 기술의 선박 엔진에 대한 적용을 위해서는 선박의 급격한 운전조건 변화와 엔진에 의한 저주파 진동에 대한 촉매 내구성 확보가 중요하다. 본 연구에서 기공 분포면에서 마이크로 기공보다는 메죠 및 매크로 기공쪽으로 구조를 개선함으로써 촉매 사용시 우려되는 배기가스중의 Soot 또는 2차 합성물질에 의한 촉매기공 막힘을 최대한 방지한 상용 SCR 촉매를 개발하였다. 또한 촉매에 대한 내구성 실증을 위하여 현재 운항 선박(한진피츠버그호)에 장착하여 실증 실험을 수행하였다. 기존 corrugate 타입의 촉매보다 40% 정도의 부피 감소와 차압 감소를 달성하였고 이로 인하여 선박내 제한된 공간에 효율적으로 SCR 시스템 설치가 가능할 것으로 생각된다. 그리고 본 연구에서는 가이드 베인 설치 없이 유동 균일화를 달성하여 반응기 전체의 크기 축소가 가능하다. 이는 추가적인 비용 및 압력 손실 저감, 유지 보수 공간 확보 등의 장점이 있다.