• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.2
• /
• pp.41-49
• /
• 2000

To understand the signal fluctuation of a wide-range oxygen sensor installed at the exhaust confluence point, when a misfiring is triggered in a cylinder, the steady state and the transient response characteristics of the sensor to the flow of the misfired gas were investigated quantitatively. It was recognized that the steady state output voltage of the sensor increased higher when it contacted the misfired gas even though the fueling condition was the same as the normal combustion case and this characteristic enabled the application of the wide-range oxygen sensor for the misfire detection. The transient response was compared at different engine speeds and it was found that the response speed increased with the engine speed. The signal fluctuation was also estimated quantitatively, using these steady state and transient response of the sensor, and the estimated signal showed satisfactory correlation with the measurements.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.1
• /
• pp.67-74
• /
• 1998

The primary cause of air pollution by vehicles is imperfect combustion of fuel. One of the most usual causes of this imperfect combustion is the misfire in IC engins. The U.S. EPA(Environment Protection Agency) and the CARB(California air Resources Board) have imposed regulations for the detection of misfiring in automotive engines. The OBD-II regulations require that misfire should be monitored by the engine diagnostic system, and that the goal of OBD-II is to alert the driver to the presence of a malfunction of the emission control system. Several solutions to the misfire detection problem have been proposed for the detection of misfires. However, the performance of these methods in the presence of misfire is not altogether clear. This paper presents a precise method and system for internal combustion engine misfire. Present invention based upon measurements of engine roughness as derived from crankshaft angular velocity measurements with special signal processing method. Crankshaft angular velocity signals are processed by WDPT, so that the more reliable misfire detection than the time domain analysis. Experimental work confirms that it is possible to apply the WDFT for the detection of misfires in no-load idle and road testing.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.27-37
• /
• 1997

Internal combustion engine is the main source of environmental pollutants and therefore better technology is required to reduce harmful elements from the exhaust gases all over the world. Especially, harmful elements from the exhaust gases are caused by incomplete combustion of mixture inside the engine cylinder and this abnormal combustion like misfire or partial burning is the direct cause of the air pollution and engine performance degradation. the object of this research is to detect abnormal combustion like misfire and to keep the engine performance in the optimal operating state. Development of a new system therefore could be applied to a real car. To realize this, the spark-plug in a conventional ignition system is used as a misfire detection sensor and breakdown voltage is analyzed. In this research, bias voltage(about 3kV) was applied to the electrodes of spark-plug and breakdown voltage signal is obtained. This breakdown voltage signal is analyzed and found that a combustion phenomena in engine cylinder has close relationship with harmonic coefficient K which was introduced in this research. Newly developed combustion diagnostic method( breakdown voltage signal analysis) from this research can be used for the combustion diagnostic and combustion control system in an real car.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.2
• /
• pp.90-95
• /
• 2006

For single engine application like T-50, advanced supersonic jet trainer, airstart capability is very important. This paper presents the results of airstart tests performed to verify T-50 airstart capability for various flight condition. The tests include spooldown, APU assisted and auto-relight airstart tests. Except for the auto-relight tests T-50 engine was successfully restarted for all airstart tests. After modifying FADEC flameout detection schedule, auto-relight tests also were successfully demonstrated. Through T-50 engine airstart tests excellent T-50 airstart capability was validated.

• Fire Science and Engineering
• /
• v.28 no.2
• /
• pp.54-63
• /
• 2014

The purpose of this study is to test the adaptability of the CO sensor as a fire detector by analyzing its sensing characteristics on fire. In order to test the applicability, we designed and made a fire testing ground whose size is similar to that regulated by UL 268, carried out real fire tests suggested by UL 268, and conducted a comparison analysis on the sensing characteristics between the CO sensor and a photoelectric smoke detector by different types of fire source. The experiment result to the sensing characteristics of the CO sensor is about twice to three times faster than that of the photoelectric smoke detector, proceeding with incomplete combustion such as paper and wood fire source in the initial fire. Especially in case of wood smoldering fire, sensing characteristics of the CO sensor is very excellent.

• Fire Science and Engineering
• /
• v.22 no.2
• /
• pp.116-120
• /
• 2008

According to the Fire Services Act revised in 2005, it has been required to set up sprinkler systems to all floors to the newly builded apartments having above 11 floors. But, according to the Fire Services Act before 2005, it had been required to set up sprinkler systems from 16 floors to the top floors to the apartments having above 16 floors. This case is the accident that a victim was dead by the fire which is inferred as an accidental fire by a cigarette butt in a 17th floor apartment unit in an apartment having 17th floors and that the bereaved family called in question why the sprinklers non worked at the fire. Through the field investigation, we checked that the sprinklers worked well when the fire detectors at the 16th floor of the apartment were operated and that the sprinklers non worked when the fire detectors at the 17th floor of the apartment were operated. We made clear that the cause of the sprinkler non-working at the 17th floor is the programming error of the sprinkler controller.

• Fire Science and Engineering
• /
• v.17 no.4
• /
• pp.124-130
• /
• 2003

This research focuses on analysis of a interaction fracture of various glasses due to contact of water sprayed curtain on hot glass surface with high temperature produced from convective heat source near glass wall. A large scaled experimental test was done in order to find the range of the glass surface temperature to be able to cause the breakage of the glasses when water droplets reach on the hot surface. This paper shows the allowable temperature of the glass surface for prevention of the cooling down breakage before water curtain droplets contact the surface. Allowable Temperature if $250^{\circ}C$ for the tempered glass but general glass is very relatively low. Therefore if the water curtain spray system was adequately activated by a thermal detector installed below ceiling adjacent glass wall with water curtain nozzle system, all hot glass would not break out by cooling water droplet's contact on the hot surface due to convective heat released by adjacent fire source near the glass wall.