• Journal of the Korean Association of Geographic Information Studies
• /
• v.9 no.2
• /
• pp.227-238
• /
• 2006

Line density index(LDI) was developed to quantify a densely isothermal line rate as standard index in the ocean environment. Theoretical background on the LDI development process restricting index range 0 to 100 was described. And validation test was done for the LDI application condition that total line length is not greater than 1/10 of unit area. NOAA SST(Sea Surface Temperature) data were used for the experimental application of LDI in the South Sea of Korea. Using GIS, $0.1^{\circ}C$ isothermal lines were linearized as vector data form SST raster data, and unit area were built as polygon data. For the LDI calculation, spatial overlapping(line in polygon) was implemented. To analyze the effect of unit area size for the LDI distribution, two cases of unit area size were designed and descriptive statistics was calculated including performing normality test. The results showed no change of LDI's essential characteristics such as mean and normality except for the range of value, variance and standard deviation. Accordingly, it was found that complex structure of thermal front and even smaller scale of front width than unit area size could influence on the LDI distribution. Also, correlation analysis performed between LDI and difference of temperature(${\Delta}T^{\circ}C$), and horizontal thermal gradient(${\Delta}T^{\circ}C/km$) on the front was obtained from linear regression model. This obtained value was compared with the results from previous researches. Newly developed LDI can be used to compare the thermal front regions changing spatio-temporally in the ocean environment using absolute index value. It is considered to be significant to analyze the relationship between thermal front and marine environment or front and marine organisms in a quantitative approach described in this study.

• Journal of the Korea Concrete Institute
• /
• v.18 no.5 s.95
• /
• pp.611-620
• /
• 2006

In the shear failure mechanism of a beam, beam and arch actions always exist simultaneously. According to the shear span to depth ratio, the proportion between these two actions is varied and the contribution of these actions to shear capacity is changed. Moreover, the current codes provide recommendations based on experimental results of normal strength concrete, so the application range of concrete strength must be extended. Based on this mechanism and new requirement, a simplified analytical equation for shear capacity prediction of reinforced high strength concrete beams without stirrups is proposed. To reflect the change in the contribution between these actions, stress variation in the longitudinal reinforcement along the span is considered by use of the Jenq and Shah Model. Dowel action with horizontal splitting failure and shear friction between cracks are also taken into account. ize effect is included to derive a more precise equation. Regression analysis is performed to determine each variable and simplify the equation. And, the formula derived from theoretical approaches is evaluated by comparison with numerous experimental data, which are in broad range of concrete strength(especially in high strength concrete), shear span to depth ratio, geometrical size and longitudinal steel ratio. It is shown that the proposed equation is more accurate and simpler than other empirical equations, so a wide range of a/d can be considered in one equation.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.610-618
• /
• 2008

It is not easy to compare the treatment processes and find an optimum operating condition by the experiments due to influent conditions, treatment processes, various operational conditions and complex factors in real wastewater treatment system and also need a lot of time and costs. In this paper, the activated sludge models are applied to four principal biological wastewater treatment processes, $A_2O$(anaerobic/anoxic/oxic process), Bardenpho(4 steps), VIP(Virginia Initiative Plant) and UCT(University of Cape Town), and are used to compare their environmental and economic assessment for four key processes. In order to evaluate each processes, a new assessment index which can compare the efficiency of treatment performances in various processes is proposed, which considers both environmental and economic cost. It shows that the proposed index can be used to select the optimum processes among the candidate treatment processes as well as to find the optimum condition in each process. And it can find the change of economic and environmental index under the changes of influent flowrate and aerobic reaction size and predict the optimum index under various operation conditions.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.12B
• /
• pp.2094-2108
• /
• 2000

오류를 수반하는 통신망을 통한 멀티미디어 데이터의 응용은 최근 그 수요가 급증하고 있다. 하지만 그 구현은 많은 문제점들을 야기하는데, 전송된 비디오 데이터에 발생한 오류를 처리하는 문제가 그 중 하나이다. 이는 압축된 비트열에 발생한 오류가 영상의 시-공간 방향으로 심각한 전파 현상을 수반하기 때문이다. 이러한 심각한 오류 전파를 완화하기 위해 본 논문에서는 EREC라 알려진 오류 제한 기법을 적용하고, 적용된 EREC의 오류 전파 특성을 분석하였다. 이를 통해, 압축 부호화된 하나의 기본 블록 (매크로 블록)이 복호시 오류가 생길 확률을 추정하였으며, 추정된 확률의 근사를 통해 양 끝단(전송단과 수신단)에서의 비디오 화질 열화를 예측하였다. 추정 확률의 근사는 매 기본 블록에서 발생된 비트수에 대한 그 기본 블록이 복호시 오류가 생길 확률을 간단한 1차식을 통한 선형 회귀법으로 모델링 되었으며, 따라서 간단한 방법을 통해 양 끝단의 화질 열화를 효과적으로 예측할 수 있었다. 부호화된 비트열이 전송 오류에 보다 강인하게 되도록 하기 위해, 본 논문에서 개발된 화질 열화 모델을 양자화기 선택에 적용함으로써, 새로운 최적 양자화 기법을 제시하였다. 본 논문에서 제안된 최적 양자화 기법은, 기존의 양자기 최적화 기법들과는 달리, 복호단에서의 복원 영상 화질이 주어진 비트율에서 최적이 되도록 양자화를 수행한다. H.263 비디오 압축 규격에 적용한 제안 양자화 기법의 실험 결과를 통해, 제안 기법이 매우 적은 계산상의 부하를 비용으로 객관적 화질은 물론 주관적 화질까지 크게 개선할 수 있음을 확인할 수 있었다.내었다.Lc. lacti ssp. lactis의 젖산과 초산의 생성량은 각각 0.089, 0.003과 0.189, 0.003M이었다. 따라서 corn steep liquor는 L. fermentum와 Lc. lactis ssp, lactis 의 생장을 위해 질소 또는 탄소 공급원으로서 배지에 첨가 될 수 있는 우수한 농업 부산물로 판단되었다.징하며 WLWQ에 적용되는 몇 가지 제약을 관찰하고 이를 일반적인 언어원리로 설명한다. 첫째, XP는 주어로만 해석되는데 그 이유는 XP가 목적어 혹은 부가어 등 다른 기능을 할 경우 생략 부위가 생략의 복원 가능선 원리 (the deletion-up-to recoverability principle)를 위배하기 때문이다. 둘째, WLWQ가 내용 의문문으로만 해석되는데 그 이유는 양의 공리(the maxim of quantity: Grice 1975) 때문이다. 평서문으로 해석될 경우 WP에 들어갈 부분이 XP의 자질의 부분집합에 불과하므로 명제가 아무런 정보제공을 하지 못한다. 반면 의문문 자체는 정보제공을 추구하지 않으므로 앞에서 언급한 양의 공리로부터 자유롭다. 셋째, WLWQ의 XP는 주제어 표지 ‘는/-은’을 취하나 주어표지 ‘가/-이’는 취하지 못한다(XP-는/-은 vs. XP-가/-이). 이는 IP내부 에 비공범주의 존재 여부에 따라 C의 음운형태(PF)가 시성이 정해진다는 가설로 설명하고자 했다. WLWQ에 대한 우리의 논의가 옳다면, 본 논문은 다음과 같은 이론적 함의를 기닌다. 첫째, WLWQ의 존재는 생략에 대한 두 이론 즉 LF 복사 이론과 PF 삭제 이론

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.6
• /
• pp.505-512
• /
• 2016

Even though high performance concrete was developed according to the trend of bigger and higher of reinforced concrete building, the rheological evaluations such as viscosity, yield stress are not enough to use as input data to accomplish the numerical analysis for the construction design. So there are many problems in the harden concrete such as poor compaction, rock pocket and crack, etc. in the field. In this study, consistency curves were measured by the viscometer as hydration reaction time passed. At the same time the slump flow test and Vicat setting test were carried out for comparing with the results of rheological properties. The fluidity of the W/B 30% decreased as the increase of replacement ratio of blast furnace slag. But in case of W/B 40%, the replacement ration did not significantly influenced to the slump flow value with the passage of hydration time. By the replacement of blast furnace slag to cement, initial setting was delayed and the time gap between initial and final setting became shorten. Through the regression analysis using Bingham model, there are a sudden changes of viscosity and yield stress around initial setting in case of low W/B 30%. The increase of workability by the change of free water in cement paste was offset by the coating effect of impermeable layer in case of W/B 40%.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.2
• /
• pp.161-168
• /
• 2011

The heating, ventilating, air conditioning (HVAC) system is a very important part of an automotive vehicle: it controls the microclimate inside the passenger's compartment and removes the frost or mist that is produced in cold/rainy weather. In this study, the numerical analysis of the defrost duct in an HVAC system and the de-icing pattern is carried out using commercial CFX-code. The mass flow distribution and flow structure at the outlet of the defrost duct satisfied the duct design specification. For analyzing the de-icing pattern, additional grid generation of solid domain of ice and glass is pre-defined for conductive heat transfer. The flow structure near the windshield, streakline, and temperature fields clearly indicate that the de-icing capacity of the given defrost duct configuration is excellent and that it can be operated in a stable manner. In this paper, the unsteady changes in temperature, water volume fraction, and static enthalpy at four monitoring points are discussed.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2003.05a
• /
• pp.189-193
• /
• 2003

금형가공에 있어서 밀링머신의 가공에서는 절삭가공의 잔유물인 버(Burr)가 생성되고, 이러한 버는 가공의 정밀도를 감소시킬 뿐만 아니라 후처리과정(Deburring)을 야기시킴으로 인해서 작업효율의 감소 및 생산성의 비효율적 낭비를 가져오게 된다. 따라서, 정밀도와 작업효율을 극대화하긴 위해서는 버의 생성원리를 파악하고, Exit Burr의 생성부분을 미리 예측하여 버의 생성을 최소화 할 수 잇는 작업 가공계획을 설계하여야 한다. (1)기존의 Burr Exit System에서는 피삭재의 단면형상인 Line과 Are처럼 단순한 형상뿐만 아니라, Line과 Are가 연결되어있는 복잡란 형상에 대해서도 버를 판별한다. 그리고, 가공 후 버가 생성되는 부분을 예측하고, 이때의 Exit Angle을 계산하여 이에 해당하는 기 실험결과 DataBase와 연동하여 생설될 버의 형상과 크기 등의 결과를 제공하여 준다. 더불어, 피삭재의 단면형상이 여러 가지 복합적인 형상으로 이루어져 있는 경우와 다양한 공구 경로까지 고려하여 실제가공과 거의 유사란 상황을 적용할 수 잇는 알고리즘으로 개발하였다. 본 논문에서는 이제까지 개발된 다양한 형상에 대한 Exit Burr 판별 알고리즘을 이용하여 임의형상을 가진 피삭재의 다중가공경로 상에서 발생 가능한 버를 예측하고, 버의 길이나 가공시간 들을 정?화 하여 최적화하는데 필요란 요소를 추출해 보고자 한다. 또한, 이를 인용하여 Face Windows에서의 버의 발생을 최소화 할 수 있는 최적 절삭가공 공구경로를 제시하여, 작업 효율성을 극대화하는 알고리즘을 Windows 응용 프로그램으로 구현하고자 한다.생성하기보다는 기존에 발생된 구매 지시의 우선적 사용과 기존 구매 지시의 납기 일자를 고객 납기에 가장 잘 맞출 수 있도록 변경하는 방안을 제시한다. 이렇게 함으로써 최대한 고객 납기를 만족하도록 계획을 수립할 수 있게 된다. 본 논문에서 제시하는 계획 모델을 사용함으로써 고객 주문에 대한 대응력을 높일 수 있고, 계획의 투명성으로 인한 전체 공급망의Bullwhip effect를 감소시킬 수 있는 장점이 있다. 동시에 이것은 향후 e-Business 시스템 구축을 위한 기본 인프라 역할을 수행할 수 있게 된다. 많았고 년도에 따른 변화는 보이지 않았다. 스키손상의 발생빈도는 초기에 비하여 점차 감소하는 경향을 보였으며, 손상의 특성도 부위별, 연령별로 다양한 변화를 나타내었다.해가능성을 가진 균이 상당수 검출되므로 원료의 수송, 김치의 제조 및 유통과정에서 병원균에 대한 오염방지에 유의하여야 할 것이다. 확인할 수 있었다. 이상의 결과에 의하면 고농도의 유기물이 함유된 음식물쓰레기는 Hybrid Anaerobic Reactor (HAR)를 이용하여 HRT 30일 정도에서 충분히 직접 혐기성처리가 가능하며, 이때 발생된 $CH_{4}$를 회수하여 이용하면 대체에너지원으로 활용 가치가 높은 것으로 판단된다./207), $99.2\%$(238/240), $98.5\%$(133/135) 및 $100\%$ (313)였다. 각각 두 개의 요골동맥과 우내흉동맥에서 부분협착이나 경쟁혈류가 관찰되었다. 결론: 동맥 도관만을 이용한 Off pump CABG를 시행하여 감염의 위험성을

• Korean Journal of Optics and Photonics
• /
• v.10 no.6
• /
• pp.500-506
• /
• 1999

We designed and fabricated a bidirectional optical transceiver module for low cost access network. An integrated chip forming a pin-PD on an 1.3 urn FP-LD was assembled by flip-chip bonding on a Si optical bench, a single mode fiber with an angled end facet was aligned passively with the integrated chip on V-groove of Si-optical bench. Gaussian beam theory was applied to evaluate the coupling coefficients as a function of some parameters such as alignment distance, angle of fiber end facet, vertical alignment error. The theory is also used to search the bottle-neck between transmittance and receiving coupling efficiency in the bi-directional optical system. Tn this paper, we confirmed that reduction of coupling efficiency by the vertical alignment error between laser beam and fiber core axis can be compensated by controlling the fiber facet angle. In the fabrication of sub-module, a'||'&'||' we made such that the fiber facet have a corn shape with an angled facet only core part, the reflection of transmitted laser beam from the fiber facet could be minimized below -35 dE in alignment distance of 2: 30 /J.m. In the same condition, transmitted output power of -12.1 dEm and responsivity of 0.2. AIW were obtained.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.6
• /
• pp.955-967
• /
• 2016

As transportation systems for connecting lands and islands, oversea long-span bridges, underwater tunnels, and immersed tunnels have been mainly used so far. Submerged floating tunnels (SFTs) moored under specific water depth are one of the newest oversea transportation system. Compared to other existing systems, the new system requires relatively less construction cost and time. But, there is still no construction example. For reasonable design of the tunnel and mooring lines the rational structural analysis should be firstly performed. Unlike common transportation structures, the submerged tunnels are mainly affected by the wave, vary irregular excitation component. So, the analysis scheme might be difficult because of the characteristics of the submerged structures. This study aims to suggest the rational global performance analysis methodology for the submerged tunnels. Using ABAQUS the dynamic response of the experimental models studied by KIOST (2013) was investigated considering regular waves. By comparing the simulation results with the experimental results, the feasibility of the numerical simulation was verified. Using the suggested method, the effects of initial inclination of the tethers and draft of the tunnel on the dynamic behavior were studied. In addition, dynamic response of a SFT under the irregular wave was examined.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1301-1307
• /
• 2011

Electrosurgical knee wand (EKW) is a high-frequency thermocautery instrument and is often used for coagulation, ablation, excision, and extirpation of knee ligaments and tissues. In order to maximize the success rate, ease, and safety of knee surgery using EKW and radiofrequency ablation, it is necessary to ensure that the EKW selectively approaches the lesion with utmost accuracy and safety. The key feature of this instrument is its excellent maneuverability. Hence, the authors constructed a tensile spring model based on a shape memory alloy (SMA), which exhibits the shape memory effect. This model can be used in knee surgery as it is considered the most biocompatible femorotibial surgical actuator. The changes in external temperature with current and the thermoelectric characteristics of the SMA were investigated. The relationship between the restoring force and the typical stroke (TS) in response to the conditions in the SMA tensile spring design were evaluated. In conclusion, as the diameter of the SMA tensile spring decreased, the maximum temperature increased. The strain in the actuator caused a stable and proportional increase in the force and induced current for up to 15s, but this increase became very unstable after 30s. Moreover, the relationship between the current and the TS was more stable than that between the current and the restoring force.