• Journal of Energy Engineering
• /
• v.21 no.3
• /
• pp.254-264
• /
• 2012

Rayleigh-Benard natural convection experiments were carried out as the preliminary experiment to simulate the natural convection of the core melt at the severe accident conditions. This work focused on the influences of plate separation distance(s), the existence of the side walls and crust geometries of upper and lower plates. Based upon the analogy concept, a cupric acid-copper sulfate electroplating system($H_2SO_4-CuSO_4$) was employed as the mass transfer system and measurements were made for $Ra_s$ ranging from $1.06{\times}10^7$ to $2.91{\times}10^{10}$. The test results measured for a single horizontal plate were in good agreement with the correlation reported by McAdams and those for two horizontal plates showed the similar trend to the existing Rayleigh-Benard heat transfer correlations developed by Dropkin and Somerscales, Globe and Dropkin. The measured heat transfer rate decreased with the increasing separation distance between the two plates and became similar to those for a single horizontal plate. Fin arrays mounted on both upper and lower plates enhanced the heat transfer rates. For all cases, the heat transfer rates measured for open side walls are higher than those for closed ones.

• Journal of Korea Water Resources Association
• /
• v.42 no.3
• /
• pp.227-234
• /
• 2009

In this study, cross correlations among sample data at each site are calculated to obtain the asymptotic cross correlations among probability weighted moments at each site using Monte Carlo simulation. As a result, the relations between the asymptotic cross correlations among probability weighted moments and the inter-site dependence among sample data at each site are nearly a linear relation with slope 1. The smaller ratio of concurrent data size to entire sample size is, the weaker the relationship grows. Simple power function which the correction term in power function accounts for the differences of the sample size between two sites was fitted to each case to estimate the parameter. It is noted that this result can be used in the various researches which include the estimation of the variance of quantile considering cross correlations.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.4
• /
• pp.154-159
• /
• 2010

Recent concrete structures have been being constructed with higher strength concrete than normal strength concrete. Therefore, it is necessary to review the applicabilities of current design codes and models for the prediction of mechanical behaviors of concrete materials such as creep. To investigate the applicability of creep model with the consideration of the strength level of concrete, three current models (ACI 209R, CEB-FIP MC90 and EC2) were studied and compared with series of experimental results. It was shown that EC2 model which is the updated model of CEB-FIP MC90 better predicts creep coefficient for high strength level concretes and showed relatively good agreements with experimental data.

• Journal of the Korean Institute of Gas
• /
• v.12 no.1
• /
• pp.48-53
• /
• 2008

The condensation heat transfer coefficients of R-22 and R-410A in a small diameter tube were investigated. The main components of the refrigerant loop consist of a receiver, a variable-speed pump, a mass flowmeter, an evaporator (preheater), and a condenser (test section). The test section consists of smooth, horizontal copper tube of 3.38 mm outer diameter and 1.77 mm inner diameter. The refrigerant mass fluxes varied from 450 to $1050\;kg/(m^2s)$ and the average inlet and outlet qualities were 0.05 and 0.95. The main results were summarized as follows : the condensation heat transfer coefficient also increases with increasing mass flux and quality. The condensation heat transfer coefficient of R-410A was slightly higher than that of R-22. Most of correlations proposed in the large diameter tube showed significant deviations with experimental data except for the ranges of low quality and low mass flux.

• Solar Energy
• /
• v.19 no.3
• /
• pp.29-41
• /
• 1999

Three-dimensional natural convective heat transfer in a vertical channel with a protruding single module was investigated experimentally. The particular interest was in the removal of thermal energy from the module by convective heat transfer. Hence radiative and conductive heat losses were estimated by using thermocouples and heat flux sensor respectively. The flow fields in the channel were visualized by means of a smoke-method. Also, local temperatures were measured by thermocouples inside the channel, along the vertical wall and module surface. It is found that convective heat transfer was promoted at the lower comer of the module and was decreased at the upper comer due to a recirculation zone. A general correlation of the critical channel ratios was found as a function of Rayleigh number. For the range of $8.28{\times}10^3<Ra^*_c<3.48{\times}10^6$, a useful correlation for the mean Nusselt number was proposed as a function of modified channel Rayleigh number.

• Journal of the Korean Institute of Gas
• /
• v.11 no.3
• /
• pp.1-6
• /
• 2007

The heat transfer coefficient and pressure drop during gas cooling process of $CO_2$ (R-744) in inclined helical coil copper tubes were investigated experimentally. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and a inclined helical coil type gas cooler (test section). The test section consists of a smooth copper tube, which is specified as the inner diameter of 4.55 mm. The refrigerant mass fluxes were varied from 200 to $600kg/m^2s$ and the inlet pressures of gas cooler were done 7.5 to 10.0 (MPa). The heat transfer coefficients of $CO_2$ in the inclined helical coil tubes increase with the increase of mass flux and gas cooling pressure of $CO_2$. The pressure drop of $CO_2$ in the gas cooler shows relatively good coincidence with those predicted by Ito's correlation developed for single-phase in a helical coil tube. The local heat transfer coefficient of $CO_2$ is well coincident with the correlation by Pitla et al. However, at the region near pseudo-critical temperature, the experiments indicate higher values than the Pitla et al. correlation.

• Korean Chemical Engineering Research
• /
• v.60 no.1
• /
• pp.145-150
• /
• 2022

Dynamic contact angles have investigated by numerous researchers for understanding interfacial behavior at moving contact lines However, due to limitation of visualization techniques, previous experiments for dynamic contact angles have conducted limitedly in hydrophilic capillary tubes based on visible ray. Recently, there is continuous need for research on dynamic contact angles in hydrophobic capillary tubes on various research and industrial fields. Therefore, in this study, we measure the dynamic contact angles of water-glycerol mixture slug in hydrophobic microtubes using synchrotron X-ray imaging. Based on the visualized data, we verified the previous experimental correlations for dynamic contact angles.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.356-361
• /
• 1996

물질전달과 열전달의 유사성을 이용하는 나프탈렌 승화법을 핵연료집합체 모델에 적용하여 봉다발에서의 국소 열전달 계수의 분포를 측정하였다. 실험 모델은 가압경수형 원자로에서 나타나는 부수로 즉, 벽면 부수로와 모서리 부수로 및 내부 부수로로 구성되는 3$\times$3 봉다발이다. 봉다발에서의 국소 열전달 계수 값은 부수로의 형상과 인접한 봉 및 벽면의 영향이 크게 작용하는 것으로 측정되었다. 내부 부수로에 둘러져 있는 봉에서의 국소 열전달계수값은 봉과 봉 사이에서는 부수로 중심 방향보다 낮았고, 평균열전달계수는 Dittus-Boelter의 상관식보다 약간 낮은 값을 보였다. 벽면 부수로에 인접한 봉에서의 열전달계수는 벽면의 영향으로 내부 부수로에 있는 봉보다 상대적으로 낮았으며, 모서리 부수로의 봉에서는 벽면의 영향이 증대되어 더욱 낮게 나타났다.

• Korean Journal of Food Science and Technology
• /
• v.23 no.3
• /
• pp.336-340
• /
• 1991

Correlations among instrumental. sensory parameters and overall preference of jelly texture were studied. Instrumental rheological characteristics of the jelly were measured with a rheometer, and sensory and overall score were measured by sensory evaluation. Instrumental maximum force was correlated to sensory hardness and shortness, and sensory springiness and stickiness were correlated to instrumental springiness and adhesiveness force respectively. Also the most significant instrumental parameters with respect to overall preference were cohesiveness and adhesiveness force with their values being 0.93 and 0.89 repectively. Multiple linear regression resulted in a following equation: overall score = 2.70 + 6.25(cohesiveness) - 0.095(adhesiveness force) with a correlation coefficient of 0.94.

• Journal of Broadcast Engineering
• /
• v.18 no.4
• /
• pp.619-630
• /
• 2013

In this paper, we propose an edge directed color demosaicing algorithm considering color channel correlation. The proposed method consists of local region classification step and edge directional interpolation step. In the first step, each region of a given Bayer image is classified as normal edge, pattern edge, and flat regions by using intra channel and inter channel gradients. Especially, two criteria and verification process for the normal edge and pattern edge classification are used to reduce edge direction estimation error, respectively. In the second step, edge directional interpolation process is performed according to characteristics of the classified regions. For horizontal and vertical directional interpolations, missing color components are obtained from interpolation equations based on intra channel and inter channel correlations in order to improve the performance of the directional interpolations. The simulation results show that the proposed algorithm outperforms conventional approaches in both objective and subjective terms.