오손에 의한 송전선로 사고 발생 피해를 최소화하기 위해서는 오손시점을 정확히 진단하고 대비하는 것이 필요하다. 송전선로의 오손 정도는 등가염분부착밀도(ESDD) 측정값을 통해 분류하고 있으며, 오손 정도에 따라 철탑과 송전선로 도체의 절연을 담당하는 애자(Insulator)의 수량 설계 및 청소 주기가 결정되어 운영되고 있다. 그러므로 정밀한 측정이 필수적인데, 기존 필세법에 의한 오손 측정방법은 세정 및 측정 방법에 따라 결과 값의 편차가 발생할 요소가 많아 개선이 필요하다. 이에 본 논문은 기존 필세법에 의한 측정 방법을 분석하여 개선 요소를 확인한 후 실험계획법에 따라 분석하여 측정 정밀도를 향상하는 방법을 제시하고자 한다.
본 연구에서는 사례기반추론, 인공신경망, 선형계획법 모형을 결합한 새로운 개념의 지능적인 경영전략수립 및 상충관계 해결 추론메카니즘을 제안한다. 본 연구에서 제안한 경영전략추론 메카니즘의 타당성을 검증하기 위하여 (1) 과거 문헌조사 결과와 (2) 비쥬얼 베이직 언어로 구현한 프로토타입인 CANNIE-SP (CAse-based Neural Network Inference Engine for Strategic Planning)를 제시하였다. 특히 본 연구에서 제안하는 인공신경망은 순방향 추론과 역방향 추론이 가능하도록 설계하여서 What-If분석 및 Goal-Seeking분석이 가능하도록 하였다. 또한 사례기반추론기관은 마이크로 소프트사의 데이터베이스 엔진인 엑세스(Access)를 사용하였다. 본 연구에서 제안하는 추론 메카니즘의 타당성을 검증하기 위하여 우리나라 화장품 시장의 실제자료를 가지고 실험하였으며 그 결과 매우 의미가 있음을 확인하였다.
Transactions of the Korean Society of Mechanical Engineers
/
v.16
no.3
/
pp.514-526
/
1992
본 연구에서는 Taguchi 방법에 사용된 직교배열 이용 실험 계획법에 의한 최 적화 방법으로 보강된 복합재 쉘 구조의 좌굴강도 최적화를 수행하고 타당성을 고찰하 였다.한 방향의 압축하중을 받는 단순 지지된 복합재 평판과 Cut-out을 가진 원통 형 판넬의 보강재 및 섬유방향 최적 설계에 본 방법을 적용시켜 본 결과, 현저한 설계 개선과 아울러 각 설계 변수가 좌굴강도에 미치는 영향을 파악할 수 있었다. 특히 이 방법은 함수의 미분값을 이용한 민감도 해석대신에 함수값의 평균치 분석(ANOM)및 분산 분석(ANOVA)을 사용하기 때문에 설계변수의 변화에 덜 민감한 설계를 얻을 수 있 다.
This paper presents the test results on the shear performance of large-size reinforced concrete beams using recycled fine aggregate to evaluate its applicability to structural concrete. The performance of these beams is compared to that of similar beams casted with natural coarse and fine aggregates. All of the beam specimens without shear reinforcement had $400mm{\times}600mm$ rectangular cross section and a shear span ratio (a/d) of 5.0. Five concrete mixtures with different replacement levels of recycled fine aggregates (0, 30, 60, 70 and 100%) were used to obtain a nominal concrete compressive strength of 28MPa. The test results of load-deflection curve, shear deformation, diagonal cracking load, crack pattern, ultimate shear strength, and failure mode are examined and compared. In addition, code and empirical equations from KCI, JSCE, CSA, Zsutty, and MCFT were considered to evaluate the applicability of these equations for predicting shear strength of reinforced concrete beam with recycled fine aggregate. The results showed that the overall shear behavior of reinforced concrete beams incorporating less than 60% recycled fine aggregate was comparable with that of conventional concrete beam. The MCFT gave good prediction and other code equations were conservative in predicting the shear strength of the tested beams. The beam specimens with replacement of 70 and 100% of natural fine aggregates by recycled fine aggregates showed different failure mode than other tested beams.
Proceedings of the Korea Water Resources Association Conference
/
2011.05a
/
pp.341-345
/
2011
본 연구는 충청북도 충주시 동량면과 금가면에 위치하고 있는 대전천을 대상으로 하상토 입경, 수위-유량의 변화에 따른 유사량 특성을 분석하였다. 하상재료 조사는 매 0.5 km 마다 17개 지점의 시료를 채취하였으며, 현장에서 채취한 하상토는 흙의 입도분포(KSF2302)시험법에 따라서 입경분석을 하였다. 측정 지점은 흐름이 안정적이며, 와류, 사수, 역류가 없고 접근이 용이하며 하상변동이 적은 지점을 고려하여 선정하였고, 유사의 이동이 활발한 시기인 7월에서 9월까지 평 저수기 20회, 홍수기 24회, 총 44회에 걸쳐 유량 및 부유사량을 현장 관측하였다. 평 저수시의 유속측정을 위해 초음파유속계를 사용하였으며, 홍수시에는 표면 부자를 사용하였다. 유량계산시에 면적은 중간단면법을 사용하여 유량을 계산하였다. 유량측정과 동시에 부유사 시료를 채취하였으며 부유사 관측에는 수심적분 채취접을 적용, 부유사농도는 여과법을 시행하였다. 본 하천의 현장실험 측정성과와 수리특성을 기초자료로 하여 각 회차에 걸친 총유사량의 산정을 SCST(Solution for Computing Sediment Transport)를 사용하였으며, 총유사량을 산정하는 Einstein공식, van Rijn공식, Toffaleti공식, Shen&Hung공식, Yang(1979)공식, Ackers & White공식, Engelud&Hansen공식, Ranga Raju공식 등 10개 공식을 적용하여 비교 분석을 수행하였다. 이중에서 관측된 부유사량을 고려하여 검토한 결과 Yang(1979)공식을 이용하여 추정한 총유사량이 가장 적합한 것으로 판단되었다. 그 결과 수위-유량관계곡선 및 유량-총유사량 관계곡선을 개발하였으며, 효과적인 치수 및 이수계획의 수립 등 수자원 기본자료로서 이용될 것이다.
In this study, we estimated inhomogeneity correction factor in small field. And, we evaluated accuracy of treatment planning and measurement data which applied inhomogeneity correction factor or not. We developed the Inhomogeneity Correction Phantom (ICP) for insertion of inhomogeneity materials. The inhomogeneity materials were 12 types in each different electron density. This phantom is able to adapt the EBT film and 0.125 cc ion chamber for measurement of dose distribution and point dose. We evaluated comparison of planning and measurement data using ICP. When we applied to inhomogeneity correction factor or not, the average difference was 1.63% and 10.05% in each plan and film measurement data. And, the average difference of dose distribution was 10.09% in each measurement film. And the average difference of point dose was 0.43% and 2.09% in each plan and measurement data. In conclusion, if we did not apply the inhomogeneity correction factor in small field, it shows more great difference in measurement data. The planning system using this study shows good result for correction of inhomogeneity materials. In radiosurgery using small field, we should be correct the inhomogeneity correction factor, more exactly.
The purpose of this study was improving the rheology properties of dentifrice by finding optimum binders polymer system which consists of carboxymethylcellulose (CMC), carbomer, and Mg/Al silicate. Response surface methodology (RSM) was employed to investigate the correlation between polymers and rheological properties of dentifrice and to optimize responses. Rheological properties were measured with oscillatory rheometer. As a result, it was identified that gel strength and yield stress were dependent on contents of CMC and carbomer and CMC caused long stringiness of dentifrice. And springness of dentifrice was dependent on contents of CMC and Mg/Al silicate. Optimum components proportion of polymers and silicate were obtained by responses optimization process. According to determined optimum components proportion, it was possible to observe a dentifrice with improved rheological properties.
Journal of the Korean Society for Aeronautical & Space Sciences
/
v.49
no.10
/
pp.859-870
/
2021
KARI (Korea Aerospace Research Institute) is developing a design framework for the concept and preliminary design of eVTOL aircrafts. A low fidelity mission analysis tool was developed for the eVTOL aircrafts of Lift-Tilt Concept, which have tilt propellers and lift propellers, using open source SUAVE package. For its development, a review for the propeller performance analysis functionality was made. To find the trim solution at each mission segment automatically, an algorithm is implemented, using a global optimization technique through parallel processings and DOE(design of experiment). Using the tool, the one seated eVTOL OPPAV(optionally piloted personal air vehicle) was modeled and evaluated, which results were compared with the preliminary design data.
Since LINAC-based stereotactic radiosurgery uses multiple noncoplanar arcs, three-dimensional dose evaluation and many beam parameters, a lengthy computation time is required to optimize even the simplest case by a trial and error. The basic approach presented in this paper is to show promising methods using an experimental optimization and an analytic optimization The purpose of this paper is not to describe the detailed methods, but introduce briefly, proceeding research done currently or in near future. A more detailed description will be shown in ongoing published papers. Experimental optimization is based on two approaches. One is shaping the target volumes through the use of multiple isocenters determined from dose experience and testing. The other method is conformal therapy using a beam's eye view technique and field shaping. The analytic approach is to adapt computer-aided design optimization in finding optimum irradiation parameters automatically.
Proceedings of the Korean Institute of Navigation and Port Research Conference
/
2016.05a
/
pp.127-129
/
2016
근래 소규모항만이 흩어져 있는 연안도서해역에서는 빈번한 폭풍의 내습으로 신규 외곽시설을 포함한 항만정비사업이 지속적으로 이루어지고 있다. 이들 항만의 경우 늘어나는 물동량에 대응하기 위해 수역시설 및 부두의 배치에 변화를 가져오고 일부 항만의 경우 만입구, 항내, 수로 등 특정해역의 준설이 다양하게 이루어지고 있어서 개발과 유지 준설에 따른 정온도의 검토가 필요한 실정이다. 본 연구에서는 바람, 파랑상호간 간섭, 흐름과의 상호작용, 쇄파 및 구조물에 대한 반사를 반영하여 수치실험을 수행하고 특히 준설작업의 규모, 방향에 따른 정온도에서 결과에 차이를 나타내어 평면배치계획에 수정을 기할 수 있게 되었다. 수치실험에는 50면 재현빈도 심해설계파 내습시 영역을 광역, 중간역, 상세역으로 하여 네스팅 기법으로 개방해역조건을 반영하였으며 외곽시설에서 해수소통 개구부의 변화에 대한 영향을 분석하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.