• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.1
• /
• pp.63-76
• /
• 2015

The purpose of this study is to suggest performance levels, a test method, and assessment criteria for the performance assessment to allow standardized tests for rockfall protection systems. The range of rockfall impact energy was determined by using domestic rockfall data and a total of 9 performance levels from 50kJ to 1500kJ were suggested. The performance assessment is implemented by two types of full-scale free-fall impact tests to investigate the serviceability and the maximum capacity as in European and American standards. It was considered to be reasonable that the specimens of rockfall protection systems consist of 3 spans and the concrete block of a polyhedron with 26 faces, similar to spheres, impacts at the center of a center span. Assessment criteria were constructed to investigate whether a rockfall penetrated rockfall protection systems and whether the deformed specimen encroached on the roadway or obstructed the vehicle traffic.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.5
• /
• pp.343-349
• /
• 2013

Crashworthy fuel cells have a great influence on improving the survivability of crews. Since 1960's, the US army has developed a detailed military specification, MIL-DTL-27422, defining the performance requirements for rotorcraft fuel cells. In the qualification tests required by MIL-DTL-27422, the crash impact test should be conducted to verify the crashworthiness of fuel cell. Success of the crash impact test means the improvement of survivability of crews by preventing post-crash fire. But, there is a big risk of failure due to huge external load in the crash impact test. Because the crash impact test itself takes a long-term preparation efforts together with costly fuel cell specimens, the failure of crash impact test can result in serious delay of a entire rotorcraft development. Thus, the numerical simulations of the crash impact test has been required at the early design stage to minimize the possibility of trial-and-error with full-scale fuel cells. Present study performs the numerical simulation using SPH(smoothed particle hydro-dynamic) method supported by a crash simulation software, LS-DYNA. Test condition of MIL-DTL-27422 is reflected on analysis and material data is acquired by specimen test of fuel cell material. As a result, the resulting equivalent stresses of fuel cell itself are calculated and vulnerable areas are also evaluated.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.12
• /
• pp.814-819
• /
• 2008

The purpose of this study was developing the building materials for creation the comfortable IAQ. By reducing formaldehyde(HCHO) known as the main factors of Sick House Syndrome. This material must be revealed the physical and eco-friendly performance, so this study set up the basic standards for building materials. The source of physical performance evaluation is Korea Industrial Standards and the base of environmental ability is the Eco Label considering certificated system related to an apartment house. Because the developed material was satisfied with the established standards, it was tested in mock-up room for obtaining the real date from indoor air. The mock-up test was conducted according environmental standard method for indoor air Quality of the ministry of environment. The result of this study were as follows; the functional building materials had a effect to reduce the formaldehyde concentration for a initial period without wall paper, so additional development is needed for application with the wall paper and the available period.

• Computational Structural Engineering
• /
• v.5 no.2
• /
• pp.12-17
• /
• 1992

지진하중에 대한 내진성능을 평가하기 위하여 유사동적 실험기법은 다양한 시험체를 대상으로 응용되어 왔다. 특히 실물크기의 시험체에 대한 실험이 가능하다는 특징 때문에 substructuring기법을 도입하여 부분구조물에 대한 유사동적실험이 활발히 진행되고 있으며, substructuring기법에 사용되는 수치적분 알고리즘의 효율성 및 새로운 보완이 필요한 것으로 판단된다. 근래에 구조물의 진동제어(vibration control)를 목적으롤 개발된 rubber bearing, viscous damper 등은 두드러진 감쇠특성을 갖고 있는 장치로서 strain-rate 효과에 비교적 민감하다. 지금까지의 유사동적실험을 준정적으로 실험이 수행되었으나, 이러한 장치가 설치된 구조물의 진동제어 성능실험을 위해서는 가능한 실시간(real time)에 가까운 실험 진행속도를 갖는 것이 유리하다. 최근에 Nakashima는 digital servomechanism을 이용하여 실시간에 가까운 실험속도의 유사동적 실험을 수행하였으며, 이에 대한 지속적인 연구를 진행하고 있다.

• Fire Science and Engineering
• /
• v.25 no.5
• /
• pp.1-7
• /
• 2011

In this study, standards and test methods for building materials of domestic and foreign countries were compared and analyzed to propose evaluation methods for the fire-retardant performance of HANOK components (Traditional house). IBC and NFPA codes recently have been adopted in the US, and the properties such as critical heat flux, fire spread index and smoke density are being used as an evaluation reference. In Europe, the unified Euroclass has been adopted and the surface flammability, prototype fire test or cone calorimeter test are conducted for the performance test. Japan has the similar system as Korea where the class is classified into 3 grades. We tried to study a quantitative evaluation method of fire retardant performance for the HANOK components based on the analysis results of the several countries' standards and test methods for building materials.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.4
• /
• pp.747-757
• /
• 2015

The main purpose of this study is to investigate the static behavior of a horizontally curved prestressed concrete (PSC) girder. A 30m long full-scale curved PSC girder with 80.0m radius is fabricated by a portable curved form system. Deflections and concrete strains at the middle of span were measured. The obtained experimental results have been compared to those from F.E.A. analysis. When a initial crack developed, the applied load was 1.3 times the service design load and the vertical deflection at the middle of span satisfied the requirement for a live load state according to the Korea Bridge Design Specifications (2010). Also, the ductility of the full scale specimen satisfied the limit in the Specifications (2010). To verify the experimental results, a numerical F.E. analysis was carried and confirmed that the data were similar with results from the test above. The horizontally curved PSC girder fabricated on site was found to have enough strength for safety under and after construction.

• Proceedings of the SAREK Conference
• /
• 2007.06a
• /
• pp.132-132
• /
• 2007

• Journal of the Korea Concrete Institute
• /
• v.16 no.5 s.83
• /
• pp.697-707
• /
• 2004

Most bridge piers were practically designed and constructed with lap spliced longitudinal reinforcing steels before the 1992 seismic design provisions of Korea Bridge Design Specification were implemented. It has been known that lap splice of longitudinal reinforcement in the plastic hinge region is not desirable for seismic performance of RC bridge piers. The objective of this research is to evaluate the seismic performance of existing circular reinforced concrete bridge piers by the Quasi-static test and to propose the need of seismic retrofit of existing bridge piers through the damage level. Test specimens were nonseismically designed with the aspect ratio 4.0 which could induce the flexural failure mode. It was confirmed from this experiment that significant reduction of seismic performance was observed for test specimens with lap spliced longitudinal reinforcing steels. Pertinent seismic retrofit was determined to be needed for existing RC bridge piers with the lap-spliced of $50\%$ longitudinal reinforcing steels.

• Journal of the Korean Society for Railway
• /
• v.16 no.5
• /
• pp.394-401
• /
• 2013

Here we report the results of an experimental laboratory test to verify the applicability to railway bridges of a PSC I girder of which the upper flange thickness was increased to improve sectional performance. The thicker this flange is, the further upward the neutral axis is moved. If in this way the span length can be increased to 40m long, the bridge may be constructed with four girders instead of five. Therefore, construction cost could be lowered by reducing the weight of the long span structure due to increased sectional efficiency. It was also necessary to be certain that the dynamic performance of this relatively flexible structure would be applicable to railway bridges. Therefore numerical analysis, as well as static and dynamic tests, was carried out for a full-size PSC I girder. Based on these results, it was verified that the performance of the PSC I railway bridge satisfied the performance criteria of the design code.

• Journal of The Korean Institute of Defense Technology
• /
• v.5 no.2
• /
• pp.1-9
• /
• 2023

The purpose of this study is to derive the need to improve the test and evaluation(T&E) performance system of the weapon systems to which advanced science and technology is applied, evaluate priorities, and present development plans. T&E of Al-based weapon systems through a literature research and case analysis on changes in the T&E environment for weapon system, 11 detailed evaluation items were derived from the in terms of the T&E system, structure, and technology. Al-based weapon system test evaluation should be performed in parallel with data-based performance evaluation and actual T&E, and performance measurement using a separate T&E data set is required for AI models performance evaluation. As a result of analyzing the importance of T&E through AHP analysis, the order of T&E system-technology-structure was evaluated, and the priority of detailed evaluation items was evaluated in the order of T&E result judgment-T&E organization and expert training-scientific T&E. For evaluation items with high priority, measures to improve the T&E performance system were presented.