• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.4
• /
• pp.268-273
• /
• 1998

Effect of aging treatment on the microstructures and mechanical properties of 6N01 Aluminium alloy was investigated by differential scanning calorimetry, transmission electron microscopy, microhardness measurement and tensile test. It was found that the precipitation sequence of 6N01 Aluminium alloy was GP zone ${\rightarrow}$ metastable hexagonal $Mg_2S_i({\beta}^{\prime})$,${\rightarrow}$ equilibrium fcc $Mg_2S_i({\beta})$, and the precipitates at peak aged condition were GP zones and ${\beta}^{\prime}$ phase. Microhardness changes during over aged condition showed very small decrease upon increased aging time. This result was attributed to the very slow transformation rate of ${\beta}^{\prime}$ to ${\beta}$. Maximum hardness(116 Hv) and tensile strength(312.6MPa) with 22.3% elongation were obtained from the specimen aged at $180^{\circ}C$ for 15hrs.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.6
• /
• pp.368-374
• /
• 2009

Nickel titanium shape memory alloys (NiTi) have been investigated for applications in the biomedical industry. However, little is known about the influences of surface modifications on the propertise of these alloys. The effect of electropolishing and heat treatments was found to exhibit significant surface roughness. Change of phase was B2, r-phase and B19' by heat treatments. In this study, effect of the electropolishing conditions on surface roughness is investigated in Ni-Ti alloys (Nitinol). Variation in phases with heat treatment temperature is investigated for a Ni-Ti alloy by X-ray diffraction and DSC. Characteristic of the microstructure have been observed by SEM. Surface roughness have been measured by AFM. The results clearly show that significant different in surface property to heat treated at $500^{\circ}C$ (R-phase). $TiO_2$ phases preciritated all of the specimens. It is not good effect of surface roughness because made to surface relief. The surface roughness appears to be important in the property of Ni-Ti alloys for biomedical applications.

• Journal of the Korean Society for Heat Treatment
• /
• v.20 no.1
• /
• pp.11-16
• /
• 2007

The fatigue properties of Ti-Ni shape memory alloy wires were investigated. In Ni-rich Ti-Ni shape memory alloys, $Ti_3Ni_4$ precipitates formed by aging treatments are believed to vary the shape memory and mechanical properties. In this study, the effect of aging temperature and aging time on shape memory properties and fatigue life were investigated using Ti-50.9 at% Ni alloy wires. The specimens were solution-treated at 1073 K for 3.6 ks followed by aging at 573 K, 673 K and 773 K for periods between 3.6 ks and 3600 ks. It was found that the fatigue life under a constant stress decreased with increasing aging temperature. When the specimens were aged at 573 K for periods between 36 ks and 360 ks, superior shape memory and fatigue properties were obtained. The fatigue life also decreased when the test temperature and strain amplitude increased. It was concluded that the fatigue life exhibited a linear relationship with the critical stress for slip.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.1
• /
• pp.30-36
• /
• 1991

Effects of aging treatment on the mechanical properties of a 18 Ni maraging steel were investigated by considering the reverted austenite. Specimens were heat treated by austenitizing at $840^{\circ}C$ for 1 hr and then aged for various times at $480^{\circ}C$ and $520^{\circ}C$. The main results obtained are as follows : 1) The amounts of reverted austenite are increased up to about 4% at $480^{\circ}C$ and about 22% at $520^{\circ}C$ with 1 to 48 hrs aging time. 2) Decreasing tendencies of impact energy and fracture toughness with increasing aging time are diminished after aging for 2 hrs at two aging temperatures of $480^{\circ}C$ and $520^{\circ}C$. 3) Peak hardness and yield strength are obtained after aging for 4 hrs at $480^{\circ}C$ and 2 hrs at $520^{\circ}C$ respectively. From the above results, it was concluded that the optimum aging condition with which showed good strength and toughness combination are given to be $480^{\circ}C$ for 4 hrs and $520^{\circ}C$ for 2 hrs.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.2
• /
• pp.38-46
• /
• 1991

Effects of aging treatment on the microstructures and microhardness of a rapidly solidified Al-Li-Cu-Mg-Zr alloy were investigated by differential scanning calorimetry(DSC) and transmission electron microscopy(TEM). The as-melt-spun ribbon was consisted of fine ${\delta}^{\prime}$ and icosahedral intermetallic compound which were precipitated in the matrix. Two exothermic peaks with the range of $120^{\circ}C-190^{\circ}C$ and $280^{\circ}C-344^{\circ}C$ corresponded to ${\delta}^{\prime}$ and ${\theta}^{\prime}$, S', $T_1$ precipitating reaction respectively, and two endothermic peaks with the range of $190^{\circ}C-280^{\circ}C$ and $344^{\circ}C-550^{\circ}C$ corresponded to dissolution of ${\delta}^{\prime}$ and ${\theta}^{\prime}$, S', $T_1$ respectively in DSC curves. Peak hardness value was obtained at $210^{\circ}C$ for 1 hr aging treatment.

• Journal of the Korean Society for Heat Treatment
• /
• v.7 no.2
• /
• pp.96-102
• /
• 1994

The present work was aimed to examine the changes of the shape and particle size distribution(PSD) of ${\delta}^{\prime}$ particles on ageing in Al-Li-(Cu, Zr) alloys which had low density, high specific strength and stiffness, Increasing ageing time and temperature resulted in particles whose aspect ratio tended toward 1. The aspect ratio of ${\delta}^{\prime}$ particles was not dependent upon the ageing temperature and time in Al-Li-Cu alloy but was dependent upon them in Al-Li-Zr alloy. The PSD of ${\delta}^{\prime}$ particles in Al-Li-Zr alloy skewed to the right hand compared with that in Al-Li-Cu alloy, because $Al_3Zr$ phase in Al-Li-Zr alloy formed before ageing promoted the precipitation and growth of ${\delta}^{\prime}$ phase. Therefore, the PSD of the ${\delta}^{\prime}$ particles was found to be affected by the presence of $Al_3Zr$ particles. The growth rate of ${\delta}^{\prime}$ phase was not affected by the existence of the third transition phase $T_1$ formed by the addition of Cu in Al-Li alloy but was affected by the existence of $Al_3Zr$ formed by the addition of Zr in Al-Li alloy.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.3
• /
• pp.138-143
• /
• 1993

Effects of aging treatment on the microstructural evolution of a rapidly solidified Al-Li-Cu alloy were investigated by differential scanning calorimetry (DSC) and transmission electron microscopy(TEM). It was found that the precipitation sequence was: supersaturated solid solution ${\alpha}^{\prime}$ ${\rightarrow}$ metastable ${\delta}^{\prime}$ + stable precipitate $T_1$ ${\rightarrow}$ stable precipitates ${\delta}+T_1$. Two exothermic and two endothermic peaks are detected by DSC analysis. The two exothermic and endothermic peaks corresponded to ${\delta}^{\prime}$ and ${\delta}+T_1$ precipitation and dissolution reactions respectively. The enthalpy of ${\delta}^{\prime}$ precipitation decreased with increasing of aging temperature and time until the finishing point of precipitation. The activation energy for precipitation of ${\delta}^{\prime}$ was measured as 80KJ/mol and the energy for dissolution was 93KJ/mol. These values arc higher than those of AI-Li binary alloy. Peak hardness value (Hv 170) was obtamed at $210^{\circ}C$ for 1hr aging treatment which coincided with finishing point of ${\delta}^{\prime}$ precipitation.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.1
• /
• pp.65-74
• /
• 1995

This research was performed to investigate the effect of ageing on grain refinement of 82wt%Cu-13.5wt%Al-4.5wt%Ni-0.1wt% misch metal alloy with ageing temperature and time. The results obtained in this study are as follows; The variation of transformation temperature with ageing temperature had very influence on ageing time at $300^{\circ}C$. But it had not influence on ageing time at $100^{\circ}C$. The variation of transformation temperature after second reversed transformation cycle was not occured in martensitic phase ageing, but $M_s$ point was appeared equally with third reversed transformation cycle in parent phase ageing. The variation of $M_s$ point was not nearly with ageing time at $100^{\circ}C$ ageing temperature. But it was decreasing with ageing time at $300^{\circ}C$ ageing temperature and $A_s$ point was increasing with ageing time. Structure of parent phase ageing was being M18R martensitic and N2H martensitic phase. It was found that ${\alpha}$ and ${\gamma}_2$ phase were created by ageing of long time at $300^{\circ}C$ ageing temperature.

• Journal of the Korean Society for Heat Treatment
• /
• v.35 no.4
• /
• pp.177-184
• /
• 2022

The present study aims to investigate the influence of Zn addition on hardness and microstructural characteristics of discontinuous precipitates (DPs) formed by isothermal aging in Mg-9%Al and Mg-9%Al-1%Zn alloys. To obtain large DPs volume fractions in the microstructure, the alloy specimens were solution-treated at 688 K for 24 h followed by water quenching, and then aged at 413 K for 48 h. The aged Mg-9%Al-1%Zn alloy had higher DPs content than the Mg-9%Al alloy, indicating that the Zn addition plays a beneficial role in enhancing age-hardening response. The DPs in the Zn-containing alloy possessed the higher hardness than those of the Zn-free alloy. Microstructural examination revealed that the increased hardness of the DPs resulting from the Zn addition is closely associated with the lower α-(Mg)/β(Mg₁₇Al₁₂) interlamellar spacing and the higher volume fraction of β phase layer of the DPs.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.6
• /
• pp.287-293
• /
• 2021

This study was intended to investigate the influence of Al content on hardness and microstructural characteristics of discontinuous precipitates (DPs) formed by isothermal aging in Mg-8.7%Al and Mg-10%Al alloys. In order to obtain large amount of DPs in the microstructure, the alloy specimens were solution-treated at 688K for 24 h followed by water quenching, and then aged at 418K for 48h. The Mg-Al alloy with higher Al content was characterized by higher volume fraction of DPs at the same aging condition, lower interlamellar spacing of the DPs, thinner β phase layer and higher β phase content in the DPs. This is closely related to the higher velocity of discontinuous precipitation process resulting from the higher Al supersaturation in the α-(Mg) matrix. The Mg-10%Al alloy showed higher hardness of the DPs and greater difference in hardness between as-cast state and DPs than the Mg-8.7%Al alloy.