• Journal of Wetlands Research
• /
• v.18 no.1
• /
• pp.68-75
• /
• 2016

A set of lab-scale polymer synthetic fiber packed column wetlands composing three columns (CW1, CW2 and CW3) with different hydraulic regimes, recirculation frequencies and pollutant loading rates, were operated in 2012. Synthetic fiber tested as an alternative wetland medium for soil mixture or gravel which has been widely used, has very high pore size and volume, so that clogging opportunity can be greatly avoided. The inflow to the wetland was artificial stormwater. All the wetlands achieved effective removal of TSS (94%~96%), TCOD (68%~73%), TN (35%~58%), TKN (62%~73%) and NH4-N (85%~ 99%). Particularly, it was observed that COD was released from the fiber during one distinct period in all wetlands. This was probably due to the degradation of polymer fiber, and the released organic matters were found to serve as carbon source for denitrification. In addition, with longer retention time and frequent recirculation, lower effluent concentration was observed. With higher pollutant loading rate, higher nitrification and denitrification rates were achieved. However, although organic matters were released from the fiber, the lack of carbon source was still the limiting factor for the system since the release persisted only for 40 days.

• Korean Journal of Optics and Photonics
• /
• v.31 no.5
• /
• pp.205-212
• /
• 2020

In the performance of a wind turbine system, the blades play a vital role. However, they are susceptible to damage arising from complex and irregular loading (which may even cause catastrophic collapse), and they are expensive to maintain. Therefore, it is very important both to find defects after blade manufacturing is completed and to find damage after the blade is used for a certain period of time. This study provides a new perspective for the detection of internal defects in glass-fiber- and carbon-fiber-reinforced panels, which are used as the main materials in wind turbine blades. A gap or fracture between fiber-reinforced materials, which may occur during blade manufacturing or operation, is simulated by drilling a hole 5 mm in diameter in the middle layer of the laminated material. Then, a digital-image-correlation (DIC) method is used to detect internal defects in the blade. Tensile load is applied to the fabricated specimen using a tensile tester, and the generated changes are recorded and analyzed with the DIC system. In the glass-fiber-reinforced laminated specimen, internal defects were detected from a strain value of 5% until the end of the experiment, while in the case of the carbon-fiber-reinforced laminated specimen, internal defects were detected from 1% onward. It was proved using the DIC system that the defect was detected as a certain level of strain difference developed around the internal defects, according to the material properties.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2003.04a
• /
• pp.139-139
• /
• 2003

원예작물은 수확 후 여러 가지 요인에 의해 품질이 저하되어 상품성을 잃게되는데, 특히 수확 후 품온상승에 의해 호흡작용이 왕성해져 품질변화를 촉진하게 된다. 그러므로 수확 후 품온을 가능한 한 빠르게 낮추어 신선도를 유지하기 위한 예냉, 저온저장, 저온수송기술등 저온유통시스템을 활용하는 것이 매우 필요하다. 저온유통시스템을 효과적으로 활용하기 위해서는 냉기의 순환이 원활하여 냉각효율이 좋고 파손의 위험과 물류비용을 줄일 수 있는 포장상자의 구조에 대한 연구가 필요하다. 포도, 방울토마토, 참외의 소비형태는 핵가족화와 더불어 신선 고품질의 농산물을 소량 구매하는 소비패턴으로 변화하면서 저온유통 및 소포장을 위한 포장형태의 개선이 요구되고 있다. 따라서 예냉.저온유통에 적합한 포장상자를 개발하기 위하여 연구소, 농협중앙회, 상자제작회사, 포장디자인 업체, 산지농협 작목반이 개발협의체를 구성하여 참외, 포도, 방울토마토의 저온유통용 골판지 상자를 개발하여 압축강도 및 냉각시험을 실시하여 소비지에 시범 보급하였다. 1. 참외 포장상자는 3kg용 상부 개방형 골판지상자로써 손잡이를 부착하고, 포장상자 상부에 덮개용 필름을 부착하였다. 제작된 상자의 압축강도는 저온유통 후 에도 안전압축강도 이상인 343kgf의 압축강도를 나타냈고, 냉각효율도 기존상자에 비하여 높게 나타났다. 또한 개발된 상자를 사용하여 시중에 출하할 경우 기존 5kg 상자에 비하여 8%이상의 부가가치를 높일 수 있었다. 2. 포도 포장상자는 소비자 기호도를 충족하고 다층적재시 손상을 방지하기 위하여 내용물을 1단 적재하고 상자를 개방형으로 하여 덮개용 필름을 부착하므로써 소비자가 내용물을 확인할 수 있도록 하고, 상자의 압축강도는 소비지까지 유통이 완료된 후 에도 수직압축강도가 400kgf이상으로 안전압축강도 보다 높아 저온에서 안전하게 유통할 수 있었다. 또한 개발된 상자를 사용하여 시중에 출하할 경우 기존 5kg 상자에 비하여 2kg상자는 21%, 4kg상자는 12%이상의 부가가치를 높일 수 있었음. 3. 방울토마토 포장상자는 외포장 상자를 4kg용 상부 개방형 골판지상자를 사용하고, 내포장상자는 500g용 PET용기를 사용하여 1상자에 8개의 내포장상자가 적재될 수 있도록 제작하였다. 제작된 외포장상자의 압축강도는 저온유통후에도 320kgf으로 안전압축강도보다 높게 나타났고, 파랫트 적재효율도 96%이상으로 나타나 물류의 효율성을 높일 수 있었다. 개발된 상자를 사용하여 시중에 출하할 경우 기존 산물형태의 4kg용 상자에 비하여 500g 내포장상자에 출하할 경우 20%이상의 부가가치를 높일 수 있었다.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.2
• /
• pp.174-190
• /
• 1996

Damage assessment based on in situ surveys for oil spills in marine environment is limited by fundamental difficulties as well as tremendous expenses. Except for intertidal zones, the damage is not preserved well. Also such surveys are usually confined to adult organisms. To overcome these limitations a computer model, NRDAM/CME, was developed in the case of USA (Reed et al., 1989), where an acute toxicity data base was used to assess indirect damages through food webs and loss due to recruitment as well as adult losses. In the present study damage assessment of natural biological resources for hypothetical oil spills is attempted using a computer model for hypothetical spills of Bunker C and heavy crude oil. In the model, the logical structure of NRDAM/CME was adopted, and biomass and productivity database were compiled for the Korean waters. The results showed that the damage increased in a nonlinear fashion as the spill amount increased. The magnitude of the damage depended upon the chemical properties of oil viscosity and solubility in particular, which implies that usage of oil dispersant might increase the damage by dispersing oil. The results also indicate that long term damage due to recruitment loss could be greater than short term damage.

• Korean Journal of Medicinal Crop Science
• /
• v.16 no.5
• /
• pp.306-312
• /
• 2008

Total sugar, crude protein, crude lipid, ash, total polyphenol, extract and betaine contents of various Lycii fructus species (Cheongyang jaerae, Myungan, Bulro, Cheongdae, Jangmyung, Cheongwoon, Cheongyang NO.6, and Cheongyang NO.7) were investigated according to harvest time at intervals of one momth from mid August to mid November. In Cheongyang NO.6, average content of total sugar and extract were the highest, 28.91% and 62.31%, respectively. In Cheongyang NO.7, crude protein (3.24%), total polyphenol (2.13%), betaine(10.77 mg/g) were the highest and crude lipid (6.82%) was the higest in Cheongdae species, and ash (5.83%) was the highest in Cheongwoon species. At the most of the species (except Cheongyang jaerae, Myungan) crude protein, crude lipid, ash and betaine contents were increased, and total sugar, total polyphenol and extract contents were decreased according to harvest time was lated. Also, a relationship among the components of Lycii fructus was found out. ; excract contents (r = 0.81) were increased as total sugar contents were increased, while crude protein (r = -0.88), crude lipid (r = -0.82), ash contents (r = -0.81) were decreased as that And betaine contents (r = 0.90) were increased as total polyphenol contents were increased.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.4
• /
• pp.149-159
• /
• 1996

Recent advances in material technology has accelerated the development of higher strength concretes using lightweight manufactured aggregates.Concretes with these chnractcristics are designable since the reductiun of dead loads and the increase in load capacity can oflix substantial cost reductions. Alt,hough thesc rharackristics are very desirable, very little information is availablc to the structural rivic;~~,cher about the properties of highstrength lightweight concrete. In general, shear strength of reinforced concrete beams is dependent on the compressive strength of concrete. the longitudinal steel ratio, the shear span to the depth ratio and shear reinforcement. In this study. eight single reinforced high strength lightweight concrete beams were tested to investigate their behavior and to determine their ultimate shear strengths.The variables studied in this investigation are shear span to effective depth ratio a/d = 1.5. 2.5, 3.5 and 4.5 : vertical shear reinforcement ratio ${\rho}_8= 0%$ and 1.136%. Test results were analyzed and compared with strengths predicted by ACI code equation. Zsutty's equation. As the results, ACI Eq.(ll-3) and ACI Eq.(ll-6) are conservative for high strength lightweight concrete beam. Also Zsuttyrs Eq. is conservative for beams except short beams. (a/d= 1.5)

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.473-476
• /
• 2008

Due to the pursuit of high function and international price increase in the field of construction, the application of the secondary product using cement is on the increase gradually in the construction industry in the pursuit of economic cost reduction by the shortening of the construction time like Expediting and the dry construction method at the same time. However, it is in very urgent situation of measures to improve the structural performance or durable performance because it is limited for use in terms of panel in interior exterior building or functional repair reinforce as yet. Accordingly, this study is to investigate applicability of permanent Formwork like mould with the structural performance or excellent durable performance in the field of construction, and to derive optimum mixture in the performance and quality of manufacture. As a result of analysis comparison with the dynamic and durable properties of vacuum extrusion molding high toughness cement panel according to the mixture of four conditions, this study has found that the test body of mixing ECC-DP3 using small filler and large granulated blast furnace slag and powder flame retardant had excellent relative hardness and bending stress strain. The durable performance has shown excellent tendency by the decrease of porosity and enhancement of water-tightness.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.2
• /
• pp.23-34
• /
• 2014

Though a dozen of different software life cycle models are suggested, there is no universal model which can satisfy all the characteristics of software. Organizations mix and match different life cycle models to develop a model more tailored for their systems and capabilities. We suggest overlapped-concurrent development life cycle model that is more suitable in various software development environment. Firstly, we divided the development process into abstract and implementation stage. Abstract stage is from software concept phase to detailed design starting time, and implementation stage is from detailed design phase to system testing phase. Next, the abstract stage introduced the overlapped phase concept that begins the next phase when the step is completed 20% by applying pareto's law. In the implementation stage, we introduced the concurrent development which the several phases are performed some time as when one use-case (UC) is completed the next development phase is started immediately. The proposed model has an advantage that it can reduce the inefficiency of development resource greatly. This model can increase the customer satisfaction with a great product at a low cost and on a short schedule. Also, this model can contribute to increase the software development success rate.

• Korean Journal of Construction Engineering and Management
• /
• v.11 no.6
• /
• pp.111-121
• /
• 2010

As the customer's interest for sidewalk block in the street or apartment complex is increasing, the materials of block which had been a concrete block exclusively are varied to clay paver, native rock and wood etc. Especially, the sales volume of clay paver which is environment-friendly and ergonomic is dramatically increasing every year with two digits growth rate, however, many problems like "Edge Cracking" "Freezing Breakage" "Bending Breakage" "Joint Gap" are happening frequently within a couple of hours after installation due to the durabilities. Because of the characteristics of Ceramic products, clay pavers are very easy to be broken when they are bumped against each other. In addition, they are relatively fragile by a freezing expansion breakage when exposed to water due to hydrophilic property as well as the intensity and absorptance of the products are varied with small difference from the production process such as production equipment and process control. Therefore, it costs a lot of money to repair the breakdown unless production and installation is carried out according to the strict criteria of the quality control. In this study, the symptoms of breakdown frequently happened in clay paver are classified by each type and finally the solution for this problem in the production of brick, installation and criteria of quality control through compressive strength and absorptance test is suggested.

• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.495-498
• /
• 2018

In this paper, we propose an DAP system for dose evaluation of medical and industrial X-ray generator. Based on the DAP measurement technique using the Ion-Chamber, the proposed system can clearly measure the exposure radiation dose generated by the diagnostic X-ray apparatus. The hardware part of the DAP measures the amount of charge in the air that is captured by an X-ray. The high-speed processing algorithm part for cumulative radiation dose measurement through microcurrent measures the amount of charge captured by X-ray at a low implementation cost (power) with no input loss. The wired/wireless transmission/reception protocol part synchronized with the operation of the X-ray generator improves communication speed. The PC-based control program part for interlocking and aging measures the amount of X-ray generated in real time and enables measurement graphs and numerical value monitoring through PC GUI. As a result of evaluating the performance of the proposed system in an accredited testing laboratory, the measured values using DAP increased linearly in each energy band (30, 60, 100, 150 kV). In addition, since the standard deviation of the measured value at the point of 4 division was ${\pm}1.25%$, it was confirmed that the DAP showed uniform measurements regardless of location. It was confirmed that the normal operation was not less than ${\pm}4.2%$ of the international standard.