• Journal of IKEEE
• /
• v.25 no.2
• /
• pp.315-321
• /
• 2021

In this paper, we have developed the multiple channel measurement system for IC Socket Test. The one can test the current-voltage measurements for pitting the several device specification, which analyze the thin current from several ㎂ to 5A with very low resistor mΩ. The increasement of the IC socket channel with lead pitch under 0.25 mm be need to perform several functions, concurrently. The system to perform these functions be designed to integrate several SMU(source measure unit) on board. So, we can reduce the 2 minutes test time per channel point to 40 sec, with daisy chain test method. Using by graphic interface, I-V curve mode and data logging technologies, we can implement the test flow methods and can make economies the time and cost.

• Convergence Security Journal
• /
• v.20 no.4
• /
• pp.3-12
• /
• 2020

Although the related regulations or guidelines are not specified in the defense weapon system R&D process, R&D authorities frequently encounter problems that require rational decision-making. If the rational process is not applied in the matter of alternative choice, the project could be disrupted, which can result in longer project periods or more resource provision. In particular, a variety of decision-making methods are needed for test&evaluation of missile R&D. The issue of selecting a test site is one of the representative decision-making problems. If it is needed to determine the priority of multiple sites, Delphi Method and Analytic Hierarchy Process(AHP) will be applied. However, if the input of cost is to be considered, Data Envelopment Analysis(DEA) is more valuable to solve the problem. This paper proposes a solution to handle quantitatively various decision-making problems that can occur in missile flight test, and shows how DEA is applied through a simulated case study of selecting a foreign test site.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.10
• /
• pp.15-25
• /
• 2010

In this study, a method for estimating the in-situ stress state of NC clays using piezocone penetration test (PCPT) results is proposed. The proposed method is based on a correlation between the PCPT results and strength increment ratio. According to proposed method, no additional testing procedure for collecting undisturbed soil sample is required, which can reduce overall testing cost. To verify this method various analytical solutions were adopted and used. Measured result and predicted result are compared with each other. The verification sites consist of a variety of soil conditions. From the comparison, it is seen that predicted value of effective strcss using the proposed method match well those from measured results.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.16 no.2
• /
• pp.237-248
• /
• 2014

Linear cutting test is known to be very effective to determine machine parameters (i.e. thrust force and torque) and to estimate penetration rate of TBM and other operation conditions. Although the linear cutting test has significant advantages, the test is expensive and time-consuming because it requires large size specimen and high load capacity of the testing machine. Therefore, a few empirical prediction models (e.g. CSM, NTNU and QTBM) alternatively adopt laboratory index tests to estimate design parameters of TBM. This study discusses the estimation method of TBM machine parameters and disc cutter consumption using punch penetration test and Cerchar abrasion test of which the researches are rare. The cutter forces and cutter consumption can be estimated by the empirical models derived from the relationship between laboratory test result with field data and linear cutting test data. In addition, the estimation process was programmed through which the design parameters of TBM (e.g. thrust, torque, penetration rate, and cutter consumption) are automatically estimated using laboratory test results.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.1
• /
• pp.79-85
• /
• 2011

Bridge Weigh-in-Motion(BWIM) system calculates a travelling vehicle's weight without interruption of traffic flow by analyzing the signals that are acquired from various sensors installed in the bridge. BWIM system or data accumulated from the BWIM system can be utilized to development of updated live load model for highway bridge design, fatigue load model for estimation of remaining life of bridges, etc. Field test with moving trucks including various load cases should be performed to guarantee successful development of precise BWIM system. In this paper, a numerical simulation technique is adopted as an alternative or supplement to the vehicle traveling test that is indispensible but expensive in time and budget. The constructed numerical model is validated by comparison experimentally measured signal with numerically generated signal. Also vehicles with various dynamic characteristics and travelling conditions are considered in numerical simulation to investigate the variation of bridge responses. Considered parameters in the numerical study are vehicle velocity, natural frequency of the vehicle, height of entry bump, and lateral position of the vehicle. By analyzing the results, it is revealed that the lateral position and natural frequency of the vehicle should be considered to increase precision of developing BWIM system. Since generation of vehicle travelling signal by the numerical simulation technique costs much less than field test, a large number of test parameters can effectively be considered to validate the developed BWIM algorithm. Also, when artificial neural network technique is applied, voluminous data set required for training and testing of the neural network can be prepared by numerical generation. Consequently, proposed numerical simulation technique may contribute to improve precision and performance of BWIM systems.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.86-86
• /
• 2011

토목 기술의 발달로 장대교량이 증가함에 따라 교면 포장도 더 심각한 진동 및 충격, 기상조건에 노출되게 된다. 교면 포장은 차량의 주행의 편리성뿐 아니라 교량 구조물을 보호해야 하는 역할도 함께 수행하기 때문에 일반 토공부의 포장과 다른 성능을 필요로 한다. 교면 포장의 특수함을 감안하여 교면 포장의 품질을 평가하고, 설계와 적용시 반영 한다면 교량의 내구 연한 및 시공, 유지관리 비용을 절감 할 수 있을 것이다. 본 논문에서는 교면 포장에 요구되는 성능을 조사하고, 교면 포장 특히, 장대 교량 적용시 교면 포장의 성능 평가를 위한 평가 방법을 고찰하였다. 교면 포장의 가장 큰 구조적 특징은 교량의 진동과 휨에 의해 포장이 받게 되는 휨응력이다. 특히 교량의 장경간화에 따라 더 큰 진동과 변형을 경험하게 되는 교면 포장은 그에 따른 충분한 휨 추종성과 피로 저항성을 확보하여야 한다. 기존 토공부 포장에서는 실험이 간단한 원통형 공시체를 이용한 간접인장강도 모드의 실험으로 피로 성능을 평가하였으나, 교면 포장은 실제 거동 특성과 유사한 빔 피로 시험 모드가 보다 신뢰성이 높을 것으로 판단된다. 빔 피로시험 모드로는 3점, 4점, 5점 휨 피로 시험 모드가 있으며, 각각의 모드는 지지점의 개수, 재하점의 개수에 따라 다른 거동 특성을 평가 할 수 있다. 최근 개발된 5점 휨 시험의 경우 교량에서 발생하는 부(-)모멘트를 모사할 수 있어 보다 현실적인 검증이 가능할 것으로 예상된다. 이 외에도 실제 크기 모형을 이용하여 윤하중을 가하는 Full-scale 모델의 경우 비용과 시간이 많이 소요되는 단점이 있으나 가장 신뢰성이 높은 방법이라고 할 수 있다. 교면 포장은 교량구조부로 수분이 침투되는 것을 막아주는 역할을 하여야 하며, 특히 해상 교량의 경우의 염분과 겨울철 사용되는 제빙화학제는 콘크리트의 열화와 강구조물의 부식을 발생시키므로 교면 포장의 방수 성능 검토는 매우 중요한 역할을 한다. 일반 토공부 포장과 달리 교면 포장은 하부층이 대기에 노출되어 있기 때문에 겨울철에 더 낮은 온도로 포장체의 온도가 내려가게 되고, 온도가 떨어진 포장층은 스티프니스가 증감함에 따라 저온 균열의 발생확율이 높아지며, 휨추종성도 나빠질 가능성이 높다. 따라서 저온에서의 균열 저항성 및 스티프니스를 평가하는 것은 교면 포장 재료의 중요한 인자 중 하나이다. 포장과 포장 하부층의 접착은 포장층의 일체화된 거동을 할 수 있게 하기 때문에 내구성 향상에 중요하다. 특히 교량과 같이 진동과 변형이 많은 경우에 있어 포장 접착층의 성능은 포장과 교량 구조물의 파손에 더 큰 영향을 미치게 된다. 접착성능은 실내에서의 직접인장모드와 전단접착강도 시험 모드의 실험이 있으며, 현장에서 측정하는 Pull-off 실험 등이 있다. 최근에 교통량과 중차량의 증가와 더불어 교량이 장경간화 되어 가면서 평가방법과 기준을 과거보다 엄격하게 할 필요성이 있다. 하지만 현실은 교면포장에 대한 시방규정이 모호하기 때문에 본 논문에서 제시한 국내외의 다양한 평가방법을 통해 적절한 교면포장의 성능을 평가하고 교면포장의 거동특성에 대한 이해를 함으로써 보다 발전된 교량기술을 확보할 수 있을 것이다.

• Korean Journal of Food Science and Technology
• /
• v.47 no.5
• /
• pp.667-672
• /
• 2015

Cynanchum wilfordii and Phlomis umbrosa Turcz. are known to contain isoflavone, a representative phytoestrogen. This study was performed to determine whether the extract mixture of C. wilfordii and P. umbrosa Turcz. would induce an estrogenic effect in ovariectomized rats. The extracts were administered to the ovariectomized rats at 30, 60, 120 mg/kg per day for 4 weeks, respectively. They showed no estrogenic effect, which was indicated by the decrease in uterus wall thickness as well as the increase in body weight and the level of cholesterol and triglyceride. The extracts also had no effect on the concentrations of estrogen and growth hormone in the serum. However, the increase in alkaline phosphatase activity, which leads to protection against the bone loss caused by ovariectomy, was noted on administration of the extract. Therefore, it seemed that the extracts of C. wilfordii and P. umbrosa Turcz. had no estrogenic effect in rats.

• KIPS Transactions on Software and Data Engineering
• /
• v.9 no.11
• /
• pp.357-366
• /
• 2020

As the proportion and complexity of software embedded in aircraft increase, risk factors such as mission failure, function failure and performance failure due to software errors also increase. In the mission-critical software systems such as aircraft software, managing requirement traceability is essential to maintain the software systems with minimal period and cost. However, the development company is not accurately complying with the guideline for managing requirement traceability due to various reasons such as development cost and schedule. Therefore, it is not easy to systematically establish and maintain requirement traceability. In the paper, we analyze actual test cases of aviation software systems from the viewpoint of requirements traceability in order to learn if there are failure cases of test cases due to the absence of systematic traceability management activities. We also check the risks associated with the failure cases according to the type and severity of the cases. As a result of analyzing a total of 7 aircraft-mounted software, failure cases could be divided into three types: omission of requirements, lack of connection between requirements and test procedures, and omission of test procedures. There were a total of 18 failure cases, 6 for each type. The numbers of high, middle and low risks were 1, 13 and 4, respectively, where the number of middle risks is largest.

• Journal of Environmental Policy
• /
• v.8 no.3
• /
• pp.53-79
• /
• 2009

This study conducted a regulatory impact analysis regarding the introduction of the Korean version of REACH(Registration, Evaluation and Authorization of Chemicals). The direct cost of the Korean REACH is estimated at a total of 101 billion Korean won over the 11 year period. The cost includes pre-registration, testing, registration, Chemical Safety Assessment(CSA) and Chemical Safety Report(CSR), evaluation, and the authorization costs of 15,223 chemical substances produced and imported more than 1 ton per year in Korea in 2006. With regard to the benefit, the only public health benefit is included in the estimation. Based on the available foreign and domestic data, this study estimated that the economic values of public health benefits are in the range of 33.2~138.6 billion Korean won if only the savings of the National Health Expenditures are considered and it reaches 203.9~1,640.3 billion Korean won if the willingness to pay(WTP) for disease prevention is included. This study proved that the Korean REACH passed the cost/benefit criteria. The benefit-cost ratio of the Korean REACH, however, is estimated to be lower than its EU counterpart. Thus it is suggested that a rigorous study to reduce the costs to industry be required before the Korean government introduces the Korean REACH.

• Journal of Korean Society for Quality Management
• /
• v.11 no.1
• /
• pp.10-17
• /
• 1983

This paper studies item-life test plans with the specified item mean life $T_1$ (MTBF) - Producer's risk ${\alpha}$ and item mean life $T_2$ (MTBF, $T_2$ < $T_1$) - Consumer's risk ${\beta}$ when the probability of item survival follows the Weibull distribution (known shape parameter) as a expansion of [1]. And Operating Characteristic Curves and Average Life-testing Times of item-life test plans are computed for this paper and [1]. Cost analysis procedures are same as [1]. These results are computed by using computer program written in Level II Basic for Apple II Plus Micro-computer. Both this paper and [6] reduce the life-testing time for Weibull distribution in comparision with Exponential distribution, but results of [6] were computed for different criterions from this paper.