• Journal of Surface Science and Engineering
• /
• v.16 no.3
• /
• pp.87-97
• /
• 1983

석출전위가 낮은 금속들을 저농도용액에서 전기분해하여 회수하는 방법에 대해 아연과 카드뮴을 모델로 삼아 채취방법을 연구하였다. Hull cell과 hyperbolic twin cell에서 시험해서 전류밀도와 효율이 낮기 때문에 기존방법으로는 회수속도가 매우 느린 것을 알 수 있었다. 전해 채취조건을 좋게 하기 위해서는 음극의 표면적을 크게 하고 흔들어 주며, 또 전해액을 강제 순환시켜 물질이동이 잘 되도록 해야만 한다. Rotating tubular bed reactor 나 impact rod reactor 같은 전해조를 사용하여 여러 종류의 용액 중의 아연과 카드뮴 전해 채취 실험을 하였다. 특히 카드뮴의 잔류농도를 낮추기 위해서는 전해법과 이온교환법을 같이 사용하는 것이 유용하다. 새로운 방법의 처리비용과 기존방법의 처리비용을 비교하여 보았다.

• Annual Conference of KIPS
• /
• 2013.11a
• /
• pp.1015-1018
• /
• 2013

최근 임베디드 펌웨어를 객체 지향 어플리케이션과 함께 개발하는 경우가 증가하고 있다. 하지만 기존의 펌웨어는 절차적 설계를 기반으로 하기 때문에 어플리케이션과 다른 설계 기법이 필요하여 개발 비용과 테스트 비용이 증가한다. 그렇지만 아두이노를 사용하면 펌웨어를 객체 지향 설계가 가능하다. 본 논문은 객체지향 적용 펌웨어를 설계에 초점을 두고, Gary E.Mogyorodi의 Test Case 생성 방법을 적용하여, 실제 펌웨어를 시험을 하고자 한다. 이 방법이 가능하면 일반적인 펌웨어와 어플리케이션을 같은 방법으로 설계 및 테스트가 가능하다. 적용사례로써, 한백전자 HBE-SmartCAR의 펌웨어를 아두이노 기반으로 설계 및 추출된 Test Case 실행을 통해, 설계와 구현이 동일함을 검증이 가능하다.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.12
• /
• pp.15-24
• /
• 2019

Weathered granite zone exists in most regions of Korea and it is often used as a bearing stratum of geotechnical structures. So it is very important to estimate the characteristics of weathered granite zone. SPT (Standard penetration test) is usually performed to investigate the characteristics of the weathered zone because undisturbed samples suitable for laboratory testing are hardly retrieved. PMT (Pressuremeter test) can reliably evaluate the in situ stress-strain behavior, but it is rarely conducted because of their high cost and time-consuming procedure. In this study, the correlation between the SPT-N values and the PMT results, obtained from the weathered granite zone, was analyzed. Empirical equations for pressuremeter modulus (E_m) and limit pressure (P_L) were suggested and compared with the previous research.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1231-1237
• /
• 2014

It is essential to perform driving performance tests of military vehicles on rough terrain. A full car test is limited by cost and time constraints, because of which a dynamic analysis via computer simulation is preferred. In this study, a vehicle model is developed using MSC.ADAMS, a commercial multibody analysis program, and compared via experiments. FTire is modeled using the results of a tire performance test to obtain the vertical stiffness. A nonlinear damper is modeled by a characteristic experiment. Leaf springs are modeled with beam force elements and consisted to a vehicle model. The vertical force and acceleration response of the wheel are identified when vehicle is passing over a simple bump as well as a sinusoidal road. The developed vehicle model is verified with the results of a full car test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.12
• /
• pp.90-95
• /
• 2006

The wall of thermal vacuum chamber which is used for the satellite thermal balance test doesn't absorb satellite's IR emission perfectly and reflects some part of that. It is estimated that small thermal vacuum chamber has relatively larger wall effect than the big one. The small thermal vacuum chamber is required for the small satellite test to reduce the test cost. A quantitative analysis was carried out to investigate the chamber wall effect. As a result, temperature errors caused by chamber wall effect was calculated, and the temperature data acquired in the thermal balance test have been compensated. By defining the optimized area ratio between chamber surface and satellite surface area, the baseline to be able to determine the minimum size of thermal vacuum chamber was established to minimize the wall effect. Also, theoretical analysis about transparent material coating which can reduce the chamber wall effect is conducted.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.158-158
• /
• 2011

통상 교량구조물은 차도부와 보도부 및 그 부속시설로서 난간 및 연석부 등으로 구성되는데, 자동차 전용도로의 경우 보도부가 설치되지 않게 되고, 국내의 국도 및 지방도상의 많은 교량이 차도부와 보도부의 별도의 구분이 없이 보행자가 연석부 위로 통행하거나 여의치 않을 경우 난간에 기대어 통행하는 경우가 일반적이어서 안전사고의 위험에 직접 노출되는 경우가 많다. 이에 국토해양부에서는 최근 "도로의 구조 및 시설기준에 관한 규칙"을 개정하여 국내의 보행자 관련 교통사고로 인한 사망자가 전체 교통사고 사망자의 약 절반을 차지하는 실정을 고려하여 보행자의 안전한 통행로 확보를 통해 보행공간의 근본적인 개선이 불가피한 실정임을 시사 하였다. 이에 국내에서는 교량 보도부의 확장에 대한 관심이 높은 실정이며, 현재 보도부 확장에 대한 시공이 활발하게 이뤄지고 있다. 그러나 기존 교량에 보도부를 신설 혹은 확장함에 있어서 보도부 부재의 설치 간격 및 필요한 앵커볼트의 수량 및 부재의 성능 평가에 대한 기준이 명확하게 이뤄지지 않은 상태에서 설치되어져 왔었다. 기존에 시공되던 H-형강의 브라켓 단면의 경우 브라켓 단면의 중량이 커서 안정성 및 시공성이 떨어지며 과다한 앵커볼트의 체결 및 브라켓 단면의 과다설계로 인한 공사기간 및 비용의 증대를 가져오는 문제점이 있었다. 이에 본 연구에서는 교량 보도부의 확장 및 신설에 있어서 보도부 부재의 설치간격의 적정성 및 브라켓의 최적화를 위한 브라켓의 성능평가 시험을 수행하였다. 브라켓의 성능평가 시험은 1차 2차 3차 시험으로 나누어 진행되었으며, 1차시험은 H-형강의 브라켓단면을 원형강관으로서의 대체 가능성을 확인하였고, 2차 시험에서는 원형강관의 브라켓 단면의 앵커볼트수량의 최적화에 대한 시험을 수행하였으며, 3차 시험은 최적화된 브라켓 단면에 프리스트레싱의 도입으로 반력 및 인발력의 감소효과를 확인하는 연구를 수행하였다. 본 연구의 수행결과 기존의 설계 및 시공방법이 과다 설계가 이뤄졌음을 판단하였고, 브라켓 단면의 최적화를 통하여 기존 시공방법에 비해 시공성, 안전성, 경제성을 높일수 있을 것으로 판단된다.

• Composites Research
• /
• v.23 no.3
• /
• pp.37-42
• /
• 2010

The fiber material properties, elastic constant and strength, are the most important factors among the various material properties for the design of composite pressure vessel, because of it's dominant influence on the performance of composite pressure vessel. That is, the deformation and burst pressure of pressure vessel highly affected by the fiber material properties. Therefore, the establishment of test method for exact fiber material properties is a priority item to design a composite pressure vessel. However, the fiber material properties in filament wound pressure vessel is very sensitive on various processing variables (equipment, operator and environmental condition etc..) and size effect, so that it isn't possible to measure exact fiber material properties from existing test methods. The hydro-burst test with full scale pressure vessel is a best method to obtain fiber material properties, but it requires a enormous cost. Thus, this paper suggests a newly developed test method, hoop ring test, that is capable of pressure testing with ring specimens extracted from real composite pressure vessel. The fiber material properties from hoop ring test method showed good agreement with the results of hydro-burst test with full scale composite pressure vessels.

• Tunnel and Underground Space
• /
• v.19 no.5
• /
• pp.440-449
• /
• 2009

LCM test is one of the most powerful and reliable methods of experiment for the cutter head design and the performance prediction of TBM. In many cases, however, the predicted design model can be directly applied to the field design, because this test may have an uppermost limit in preparation and/or transportation of the large size rock samples and the test for the jointed rock mass is not easy. When the proper and reasonable numerical modeling is considered to overcome this limit, the most adequate cutter head design for TBM could be presented without any complicate preconsideration in the field. In this study, the crack propagation patterns dependent on the contact point of disc cutter and the angle of rock joint are analyzed for the rock specimen with a single joint using the UDEC. The authors could derive the appropriate contact points of disc cutters and their space with respect to the joint angle in rock mass thru the numerical analysis.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.5
• /
• pp.29-36
• /
• 2008

The shotcrete is a NATM technique as a major tunnel support for ground stability after tunnel excavation. Instead of a general concrete lining method, it is a trend for curtail of construction periods and reduction of construction expenses that required to use of the permanent shotcrete lining. This high-strength shotcrete is required to use as a permanent shotcrete lining. This brought out the solution of environmental pollution and harmfulness to human. Accordingly, in this study specimens for strength measurement were made to develop shotcrete possible to develop materials in early with cement mineral accelerator as NATM method construction. It was compared with existing shotcrete material, unconfined compression test, flexural strength test, antiwashout underwater test were experimented. The fish poison test was experimented to evaluate an influence of environment. As a results of the test, unconfined compressive strength and flexural strength were equivalent with 28-curing day strength of existing material. An antiwashout of research subject material was revealed excellently in antiwashout Underwater test. As a results of the fish poison, an evaluation research subject material was founded more environmentally friendly than existing shotcrete.

• Journal of Software Engineering Society
• /
• v.28 no.1
• /
• pp.7-12
• /
• 2019

Recently, as the weight of software in the weapon system increases, the quality of the software becomes a very important factor. In order to improve the quality of the weapon system software, DAPA(Defense Acquisition Program Administration) has institutionalized software reliability in Weapon System Software Development and Management Manual. The manual presents specific methods and procedures to improve the weapon system software quality. In order to meet the required reliability test standards specified in the manual, it is necessary to continuously detect and correct defects throughout the entire development period. However, it is difficult to build proper reliability test environment due to the cost of software reliability tools, setting up secured and separated network environment, and etc. Therefore, in this study, we propose an efficient environment construction method for software reliability test of defense industry field in restricted development environment and limited resources.