• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2011년도 춘계학술논문집 2부
• /
• pp.824-827
• /
• 2011

본 논문에서는 자동차 시트 리클라이너 기어의 파인 블랭킹 성형 실험을 통하여 V-링 설치 위치에 따른 기어의 다이 롤 높이 변화를 검토하였다. 3 종류의 다이 편과 가이드 플레이트 편을 설계하여 파인 블랭킹 금형을 제작하였으며 650 ton 파인블랭킹 프레스에서 성형 실험을 수행하였다. 실험으로부터 제품을 취출하여 다이 롤 높이를 측정하여 분석한 결과 기어 모듈과 관계없이 V-링 설치 위치가 가이드 플레이트에서 멀어짐에 따라 다이 롤 높이가 증가함을 파악할 수 있었다. 이와 같은 결과는 향후 파인 블랭킹 금형의 V-링을 설계할 때 다이 롤 높이를 최소화하기 위하여 유용하게 활용될 수 있을 것이다.

• 동력기계공학회지
• /
• 제15권5호
• /
• pp.67-71
• /
• 2011

Fine blanking is a specialized form of blanking where there is no fracture zone when shearing. This is achieved by compressing the whole part and then an upper and lower punch extract the blank. This allows the process to hold very tight tolerances, and perhaps eliminate secondary operations. In the present study, tensile test and numerical simulation has been performed to investigate distribution of deformation and stress of car seat recliner. The commercial ABAQUS/Explicit software was applied for analyzing the stress and strain of the recliner. In analysis, three lock gear has reached the maximum moment on rotational degree of 2.27. This is more than two times than maximum moment of same size recliner, and can be used safely. Therefore, these can use as criterion of actual structural design.

• 한국기계가공학회지
• /
• 제17권1호
• /
• pp.101-107
• /
• 2018

In this study, the analysis of radiation noise and chattering noise of vehicle seat recliner was conducted through testing and analysis. First, operating noise was measured by seat back frame and recliner, and chattering noise was confirmed. Next, the transient dynamic analysis was performed, and the result was mapped to the acoustic analysis. Finally, the test and analysis were compared and analyzed. The results are as follow. First, it was found that the peaks appeared in common in the range of 620~650Hz, 1,240~1,290 Hz, and 1,840~1,940 Hz. It was judged that the dynamic characteristics of the recliner system overlapped with the rotation component of the motor to cause amplification of noise and vibration. Next, as a result of imaging the radiation noise analysis, it was judged that the noise radiated in the forward and backward direction has a greater influence than the direction of the rotation axis when the ear position of the person is taken as a reference.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.22-30
• /
• 2016

It is very important to obtain the net shape of the product to maximize the shear cutting surface of fine blanking. In this paper, the fine blanking die was manufactured to achieve part characteristics, such as flatness and a fully sheared surface. The V-ring in the fine blanking die was designed to prevent lateral movement of the material. The fine blanking experiment was conducted with the fine blanking die. The material usage rate was increased by over 5.7% and that of the water-soluble lubricant was decreased by over 33% when the 2-cavity die technology was applied to fine blanking. The capacity of the existing press could lead to productivity improvement and cost reduction. Thus, 2-cavity die technology for fine blanking with a minute module of an accurate gear for producing seat recliner parts was developed.

• 한국기계가공학회지
• /
• 제16권6호
• /
• pp.15-20
• /
• 2017

This study analyzed the load change of the gear generated by the operation of the vehicle recliner through Finite Element Analysis. The basic model of the recliner used was a commercial product, and the effect of the seat frame was excluded. The load conditions applied to the recliner were set considering gravity, the mass of the seat's back frame, and the weight of a person. The operating mode was set to move the seat back from the vertical to the reclined position. As a result, it was found that the tooth bending amount of the gear rim and wheel increased from the cam rotation angle of 450 degrees, and a change in the contact ratio occurred. Furthermore, excessive torque fluctuations occurred in the ranges of 390 to 450 and 750 to 710 degrees. It was found that this occurred in the region of about 30 degrees before and after the point where the x-axis direction load is larger than the y-direction load. From this torque fluctuation it was determined to likely to cause chattering noise.

• 한국자동차공학회논문집
• /
• 제17권1호
• /
• pp.64-71
• /
• 2009

The development of more safe recliners is an important issue in the automotive industry. However, the development of new recliners is costly and take much time because it is typically based on experimental evaluation using prototypes. This study presents the evaluation of rear crashworthiness for round recliner using finite element method. That reduces the number of repeating test and gives an information about stiffness. To evaluate rear crashworthiness, the FMVSS 301 simulation and pendulum impact simulation were performed. The load path on two simulations was observed and compared each other in this paper. Also stress, strain and internal energy was compared. It is attempted the tooth strength simulation using a substructure option on PAM-CRASH.

• 한국정밀공학회지
• /
• 제25권7호
• /
• pp.64-71
• /
• 2008

Burr generated on plate holder should be removed through additional process, because it has an influence on the function of automotive seat recliner. The process layout to perform simultaneously embossing and half blanking of plate holder has been developed in this study in order to minimize the influence of burr formation. The optimal process condition to satisfy the required dimensional accuracy of plate holder has been determined using Taguchi method and finite element analysis. It has been shown from experimental results that the proposed method is decidedly superior to the previous FCF method from the aspect of sheared surface, roll-over, flatness and burr height.

• Tribology and Lubricants
• /
• 제35권3호
• /
• pp.183-189
• /
• 2019

The driver seat of an automobile is in direct contact with the driver and provides the driver with a safe and comfortable ride. The seat consists of a frame, a rail, and many recliners. In recent years, strength and operating force measurement testing of the recliner have become vital for designing car seats. However, performance evaluation requires expensive testing equipment, numerous seat products, and considerable time. Therefore, the trend is to reduce experimentation through interpretation. This study examines the lubrication of solid lubricant for automotive seat recliners and confirms the friction and wear performance. In this study, the lubrication behavior of solid lubricants for car seat recliners is investigated to ascertain the friction and wear performance and to provide accurate values for the strength analysis. The friction material consists of a pin and a plate made from steel, which is widely used in recliners. The friction and wear under lubrication conditions are measured by a reciprocating friction wear tester. The friction coefficient is obtained according to the load and speed. Based on the obtained results, it is possible to achieve a reduction in the error of the test value and the analysis by providing the friction coefficient and wear of the lubricant. The results can be applied to the analysis of automobile seat design.

• 대한기계학회논문집A
• /
• 제34권11호
• /
• pp.1623-1630
• /
• 2010

본 연구에서는 자동차용 시트 리클라이너의 주요 부품인 섹터투스 결합부의 롤오버 저감을 위한 효과적인 성형 방법을 제시하였다. 기존의 성형 공정에 의하여 발생한 과도한 롤오버 때문에 섹터투스 내측기어와 결합 부품인 폴투스 외측기어 간의 정확한 결합이 이루어지지 않아 승차감 및 안전성이 저하된다. 따라서 성형 시, 소재를 롤오버 측으로 유동시켜 롤오버량을 최소화 해야 하며, 이를 위하여 국부 돌기형 다이, 코이닝 펀치를 이용한 방법 및 가변 역클리어런스를 통한 롤오버 저감 방법에 대해 유한요소해석으로 비교 평가 하였고, 이를 검증하기 위해 금형 제작 및 실험을 수행하였다. 실험 결과, 가변 역클리어런스를 이용한 방법이 롤오버 저감 및 금형 강도 측면에서 우수한 특성을 가지는 것을 확인할 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.125-126
• /
• 2012