• Korean Journal of Ecology and Environment
• /
• v.33 no.3 s.91
• /
• pp.222-229
• /
• 2000

Spatial and temporal variation of phosphorus in response to intensity of summer monsoon was evaluated in Taechung Reservoir during 1993${\sim}$1994. Total phosphorus (TP) averaged 31 ${\mu}$g/l during the study and varied from 6 to 197 ${\mu}$g/l. Concentrations of TP were highest in the headwaters during the monsoon of July${\sim}$August 1993, and these values were mainly made of particulate P and were closely associated (R$^{2}$=0.74, p<0.001) with high inorganic suspended solids (NVSS). In-lake TP in the headwaters was mainly influenced by the watershed runoff and declined toward the dam. Values of TP downlake was only one-fifth of the peak in the headwaters and had no correlation with NVSS. In 1994, inlake TP was markedly lower relative to 1993 and showed low spatial and temporal variation. Maximum TP during monsoon 1994 in the headwaters and mid-lake was 72% and 52% lower, respectively, than in those two zones in 1993 whereas TP downlake was similar between the two years. These results suggest that temporal variation downlake is much less influenced by seasonal inflow compared to the haedwaters. In 1993, mean TP before fall overturn, based on average value for all sites, was significantly (t=5.99, p<0.001) greater than the mean after fall overturn, whereas in 1994 mean TP after fall overturn (32 ${\mu}$g/l) was greater. This outcome indicates that in 1993 major P-input originated from the external source from the watershed during the intense monsoon, whereas in 1994 internal processes dominated during the weak monsoon. Overall data suggest that annual budget of inlake P is regulated by intensity of the summer monsoon, and phosphorus data measured at single site near the dam or headwater zone may not be represent seasonal trends of the system due to large spatial variation of Taechung Reservoir.

• Journal of Biosystems Engineering
• /
• v.8 no.1
• /
• pp.9-16
• /
• 1983

This study was conducted to find out the effects of such parameters as specific draft resistance, slip rate, and fuel consumption rate on plowing performance in paddy fields spread with chopped rice straw. The plowing operation by an 8 P.S. power tiller was carried out in 6 different fields having the soil moisture content of 27~36 percent in dry basis in clay loam soil texture, and applying chopped rice straw of 10, 20, 30 and 60cm in length in the spring of 1982. The effects of soil hardness and moisture content on the plowing performance were also investigated. The results of the study are summarized as follows; 1. The minimum draft during the plowing operation was 110kg in the 30cm rice straw plot having the soil moisture content of 32 percent in dry basis. 2. The multiple regression equation of the specific draft(D) as a function of soil moisture content(M) and cutting length of rice straw(L) was obtained as follows. $D=14.1978-0.8565M+0.0661LxM-2.9685L+0.0133M^2+1.093L^2$ 3. In the 30cm rice straw plot with the soil moisture content of 32 percent in dry basis, the minimum specific draft resistance and the rate of slip were 0.35kg per $cm^2$ and 16 percent respectively. The specific draft resistance varied sensitively in accordance with the soil moisture content, and the slip rate of power tiller was dependent upon the cutting length of rice straw rather than the soil moisture content. 4. The highest plowing performance was 5.3 ares per hour at the soil moisture content of 35 percent and soil hardness of 10kg per $cm^2$. The relationship between the plowing performance and the soil moisture content was obtained by a quadratic equation. 5. The minimum fuel consumption rate in the plowing operation was recorded 6.5 liters per 10 ares in 30cm chopped rice straw plot with the soil moisture content of 32 percent in dry basis.

• Economic and Environmental Geology
• /
• v.17 no.3
• /
• pp.179-195
• /
• 1984

The Jurassic Daejeon and Nonsan granitoids are "S-type" syntectonic calc-alkaline two-mica monzogranite and granodiorite, respectively. With evidences of high CaO, $Al_2O_3$, LIL/HFS elements, total REE, (Ce/Yb)N and initial ($^{87}Sr/^{88}Sr$) ratio, and no significant Eu anomaly, the primary magmas for the Daejeon and Nonsan granitic rocks are derived from partial melting of the Precambrian granulite (e.g. grey gneisses). But those Jurassic granitoids crystallised from different chemical characteristics of parental magmas which is mainly due to varying degree of partial melting of the granulite (crustal anatexis). The absence of significant anomalous Eu($Eu/Eu^*=O.82{\sim}1.00$) in the Daejeon and Nonsan granitoids could indicate that feldspars, mainly plagioclase, did not separate from the magmas. The parental hydrous magmas could not rise appreciably above their source region before crystallisation. The Jurassic granitoids may be resulted by closing-collision situation and belong to the Hercynotype (Pitcher 1979) such as compressive ductile regime of an intracontinental orogen.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.37 no.2
• /
• pp.178-184
• /
• 1992

The changes in contents of chlorophyll and free proline in the seedling leaves of ten rice cultivars as affected by salt stress were checked in order to obtain the basic information on the judgement of the degrees of salt injury. The difference in salt injury among the cultivars was clearly observed about 25 days after 6% salt treatment. Chlorophyll content was decreased in both Gayabyeo and Taebaegbyeo for 14 days after different salt treatment as salt concentration was increased and the decreased tendency was much higher in Taebaegbyeo than in Gayabyeo over 0.4% salt concentration. Chlorophyll content in Gayabyeo after 0.6% salt treatment was decreased slowly, while in Taebaegbyeo, deminished very rapidly as time progressed, therefore it decreased by about 16% in Gayabyeo and 67% in Taebaebyeo compared to the control at 20 days, respectively. The relationship between chlorophyll content and the degrees of salt injury in ten rice cultivars showed significant negative correlation at 10 day after 0.6% salt treatment. Free proline content in Gayabyeo was increased gradually for 14 days after different salt treatment as salt became higher, while in Taebaebyeo, it was increased rapidly under 0.6% but rather decreased under 0.8% salt concentration. Particularly, it was much higher Taebaegbyeo than in Gayabyeo under salt concentration from 0.4 to 0.6%. Free proline content in Gayabyeo after 0.6% salt treatment was increased from 15 days, on the other hand in Taebaegbyeo, it was increased from 5 days, but rather decreased from 20 days, and it was 6 times higher in Taebaegbyeo than in Gayabyeo at 10 days. There was significant positive correlation between free proline content and the degrees of salt injury in ten rice cultivars at 10 days after 0.6% salt treatment. From the above results, chlorophyll and free proline content may be used as an indicative character of intensity of salt stress as well as varietal difference in resistance to salt stress in the seedling stage.

• The Journal of the Petrological Society of Korea
• /
• v.24 no.1
• /
• pp.25-54
• /
• 2015

Syenite is not a common rock, unlike granitic rocks formed the major component of the continental crust. The aim of this study is to decipher the occurrences and detailed descriptive characteristics of the syenite distributed in Sancheong area, and to investigate the petrogenesis of the syenitic magma based on geochemical study. The dominant minerals in syenite are alkali feldspar (usually orthoclase and rarely microcline), plagioclase, amphibole, biotite, and quartz. Syenites are found in a wide variety of colors. The anhedral hornblende and biotite filling the boundary of feldspar and quartz indicate that the hydrous minerals were crystallized lately, and that water was insufficient at the beginning of crystallization in magma. According to the analysis of mineral composition, amphibole in syenite is mostly ferro-edenite, and the pressure is calculated as 3.3~4.9 kb with 11.9~17.3 km of emplacement depth. Biotite and pyroxene are plotted in the region of annite and hedenbergite, respectively. Based on petrochemical studies of major elements, syenite belongs to alkaline series, metaluminous, and I-type. On the other hand, the variation patterns of trace and rare earth elements of syenite differ from the patterns of diorite and granite. In the geochemical characteristics, syenite is different from gabbro-diorite spatially adjacent to syenite, as well as granite. These results suggest that each rock has been generated from the different sources of magma. Additionally, based on the experimental data, the syenitic magma can be formed (1) by the partial melting at a high pressure and dry system, (2) when the initial crystallization minerals to be residue with migration of the residual melts separated from the ascending cotectic magma (3) when fluorine compositions to be plentiful in the protolith and/or at depth of the magma. Based on the petrographic characteristics of the syenite, Sancheong syenitic magma may have been formed by partial melting in a dry system.

• Radiation Oncology Journal
• /
• v.22 no.1
• /
• pp.64-68
• /
• 2004

Purpose : To study the feasibility of verifying real-time 2-D dose distribution measurement system with the scintillation screen for the quality assurance. Materials and Methods : The water phantom consisted of a scintillation screen (LANEX fast screen, Kodak, USA) that was axially located in the middle of an acrylic cylinder with a diameter of 25 cm. The charge-coupled device (CCD) camera was attached to the phantom In order to capture the visible light from the scintillation screen. To observe the dose distribution In real time, the intensity of the light from the scintillator was converted to a dosage. The isodose contours of the calculations from RTP and those of the measurements using the scintillation screen were compared for the arc therapy and the Intensity modulated radiation therapy (IMRT). Results : The kernel, expressed as a multiplication of two error functions, was obtained in order to correct the sensitivity of the CCD of the camera and the scintillation screen. When comparing the calculated isodose and measured isodose, a discrepancy of less than 8 mm in the high dose region was observed. Conclusion : Using the 2-D dosimetry system, the relationship between the light and the dosage could be found, and real-time verification of the dose distribution was feasible.

• Journal of Korea Water Resources Association
• /
• v.47 no.6
• /
• pp.501-511
• /
• 2014

The effects of initial conditions and input values of the rainfall-runoff model were studied in the applications of a lumped concept model for flood event data extension. For the initial conditions of the rainfall-runoff model, baseflow effects and spatial distributions of saturation points ($R_{sa}$) for the storage function methods (SFM) were analyzed. In addition, researches on the effects of rainfall data conditions as input values for the rainfall-runoff model were performed. The Chungju Dam watershed was selected and divided into 3 catchments including smaller size of 22 sub-catchments. The observed discharge and inflow amounts at Yeongwol 1, Chungju Dam, and Yeongwol 2 water level stations were individually operated as criteria for flood data extension in 30 flood events from 1993 to 2009. Direct and base flow were distinguished from a stream flow. In order to test capability of flood data extension, obtained base flow was applied to the rainfall-runoff model for three water level stations. When base flow was adopted in the model, the Nash-Sutcliffe Efficiency(NSE) was increased. The numbers of over satisfaction for model performance (>0.5) were increased over 10%. Saturation points ($R_{sa}$) which strongly influence the runoff amount when rainfall starts were optimized based on the runoff amount at three water level stations. The sizes of saturation points for three locations were similar which means saturation point size is not depending on the runoff amount. The effects of rainfall information for flood runoff were tested at 2002ev1 and 2008ev1. When increased the amount of rainfall information, the runoff simulations were closer to the simulations with full of rainfall information. However, the size of improvement was not substantial on rainfall-runoff simulations in terms of the size of total amount of rainfall.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.667-678
• /
• 2002

In this paper, a new radiating structure with a multi-layered two-dimensional metallic disk array was proposed for shaping the flat-topped element pattern. It is an infinite periodic planar array structure with metallic disks finitely stacked above the radiating circular waveguide apertures. The theoretical analysis was in detail performed using rigid full-wave analysis, and was based on modal representations for the fields in the partial regions of the array structure and for the currents on the metallic disks. The final system of linear algebraic equations was derived using the orthogonal property of vector wave functions, mode-matching method, boundary conditions and Galerkin's method, and also their unknown modal coefficients needed for calculation of the array characteristics were determined by Gauss elimination method. The application of the algorithm was demonstrated in an array design for shaping the flat-topped element patterns of $\pm$20$^{\circ}$ beam width in Ka-band. The optimal design parameters normalized by a wavelength for general applications are presented, which are obtained through optimization process on the basis of simulation and design experience. A Ka-band experimental breadboard with symmetric nineteen elements was fabricated to compare simulation results with experimental results. The metallic disks array structure stacked above the radiating circular waveguide apertures was realized using ion-beam deposition method on thin polymer films. It was shown that the calculated and measured element patterns of the breadboard were in very close agreement within the beam scanning range. The result analysis for side lobe and grating lobe was done, and also a blindness phenomenon was discussed, which may cause by multi-layered metallic disk structure at the broadside. Input VSWR of the breadboard was less than 1.14, and its gains measured at 29.0 GHz. 29.5 GHz and 30 GHz were 10.2 dB, 10.0 dB and 10.7 dB, respectively. The experimental and simulation results showed that the proposed multi-layered metallic disk array structure could shape the efficient flat-topped element pattern.

• Journal of Gastric Cancer
• /
• v.5 no.3 s.19
• /
• pp.174-179
• /
• 2005

Purpose: The 5-year survival rate is the most useful parameter for evaluating the effect of management on most malignant tumors. Recurrence after a curative resection for gastric cancer occurs mostly within 3 years of the operation, which caused us to evaluate whether a 3-year disease-free survival (3DFS) can be substituted for a 5-year overall survival (5OS). Materials and Methods: We reviewed the medical records of 656 consecutive patients who had undergone a curative resection for gastric cancer To assess whether 3DFS represents 5OS, we used a simple linear regression with survival probability calculated by using the survival function. Results: Recurrence was found in 175 cases during the follow-up periods. The accumulative frequencies of recurrence at postoperative 1 year, 3 years, and 5 years were 46% (81 cases), 89% (156 cases), and 97% (170 cases), respectively. The correlation coefficient (r) and the coefficient of determination $(r^2)$ between 3DFS and 5OS were 0.87 and 0.76, respectively, and the regression equation was $5OS=0.18+(0.80{\times}3DFS)$. The r and $R^2$ according to the type of recurrence were 0.89 and 0.80 in peritoneal seeding, 0.88 and 0.78 in hematogeneous metastasis, and 0.86 and 0.73 in local recurrence, respectively. The r (0.77) and $r^2$ (0.60) were relatively lower in low stages (stage I and II) compared to r (0.88) and $r^2(0.77)$ in high stages (stage III and IV). Conclusion: The 3DFS is an excellent predictor of 5OS. Therefore, if we use the former as the treatment evaluating method, 2-year time reduction in assessing and reporting treatment results is expected.

• Progress in Medical Physics
• /
• v.3 no.2
• /
• pp.1-12
• /
• 1992

For intraoperative radiation therapy using electron beams, a cone system to deliver a large dose to the tumor during surgical operation and to save the surrounding normal tissue should be developed and dosimetry for the cone system is necessary to find proper X-ray collimator setting as well as to get useful data for clinical use. We developed a docking type of a cone system consisting of two parts made of aluminum: holder and cone. The cones which range from 4cm to 9cm with 1cm step at 100cm SSD of photon beam are 28cm long circular tubular cylinders. The system has two 26cm long holders: one for the cones larger than or equal to 7cm diamter and another for the smaller ones than 7cm. On the side of the holder is an aperture for insertion of a lamp and mirror to observe treatment field. Depth dose curve. dose profile and output factor at dept of dose maximum. and dose distribution in water for each cone size were measured with a p-type silicone detector controlled by a linear scanner for several extra opening of X-ray collimators. For a combination of electron energy and cone size, the opening of the X-ray collimator was caused to the surface dose, depths of dose maximum and 80%, dose profile and output factor. The variation of the output factor was the most remarkable. The output factors of 9MeV electron, as an example, range from 0.637 to 1.549. The opening of X-ray collimators would cause the quantity of scattered electrons coming to the IORT cone system. which in turn would change the dose distribution as well as the output factor. Dosimetry for an IORT cone system is inevitable to minimize uncertainty in the clinical use.