• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.172-177
• /
• 2010

This study reports the high-temperature oxidation kinetics, ASR(area specific resistance), and interfacial microstructure of metallic interconnects coated with conductive oxides in oxidation atmosphere at $800^{\circ}C$, The conductive material LSC($La_{0.8}Sr_{0.2}CoO_3$, prepared by Solid State Reaction) was coated on the Crofer22APU. The contact behavior of coating layer/metal substrate was increased by sandblast. The electrical conductivity of the LSC coated Crpfer22APU was measured by a DC two probe four wire method for 4000hr, in air at $800^{\circ}C$. Microstructure and composition of the coated layer interface were investigated by SEM/EDS. These results show that a coated LSC layer prevents the formation and growth of oxide scale such as $Cr_2O_3$ and enhances the long-term stability and electrical performance of metallic interconnects for SOFCs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.137-137
• /
• 2010

This research proposed an advanced Electronic bead (EB) using MMA (Methy methacrylate) and CCA (Charge Control Agent). In the first, this paper presents about measurement method and characterization analysis of EB with wet coating method. Furthermore, this work presents the positive and negative EB fabrication procedure. As the experimental results, the proposed EB with charge to ratio[Q/M] is very attractive to Electronic paper driving characterization.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.2
• /
• pp.88-93
• /
• 2005

Anode-supported solid oxide fuel cell (SOFC) was investigated to increase the cell power density at intermediate temperature through control of the cathode structure. The anode-supported SOFC cell were fabricated by wet process, in which the electrolyte of $8mol\%\;Y_2O_3-stabilized\;ZrO_2 (YSZ)$ was coated on the surface of anode support of Ni/YSA and then the cathode was coated. The cathode has two- or three- layered structure composed of $(La_{0.85}Sr_{0.15})_{0.9}MnO_{3-x}(LSM),\;LSM/YS$ composite (LY), and $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3{LSCF)$ with different thickness. Their single cells with different cathode structures were characterized by measuring the cell performance and ac impedance in the temperature range of 600 to $800^{\circ}C$ in humidified hydrogen with $3\%$ water and air. The cell with $LY\;9{\mu}m/LSM\;9{\mu}m/LSCF\;17{\mu}m$ showed best performance of $590mW/cm^2$, which was attributed to low polarization resistance due to LY and to low interfacial resistance due to LSCF.

• Plant Journal
• /
• v.16 no.1
• /
• pp.34-37
• /
• 2020

The need to improve the performance of the dust collector by increasing the fine dust pollution in Korea is eminent. In this study, electrostatic spray wet electrostatic precipitator is used to remove Particulate Matter (PM). In order to enter the Cone-jet mode, which is the most stable spray mode among the various modes of electrostatic spraying, an appropriate voltage-flow condition must be satisfied, and a voltage-flow interval enabling this can be expressed as Stability Island. The voltage at which the conduit mode starts in the Stability Island section is referred to as the electrostatic spray minimum voltage (Onset Voltage). However, the conventional electrostatic spray is uses a very low flowrate, at most few millilitres per minute. The use of much higher flowrates has introduced different patterns of electrospray modes. In this study, the different spray modes will be studied in detail.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.4
• /
• pp.135-139
• /
• 2014

The hydride vapor phase epitaxy (HVPE) grown GaN samples to precisely measure the surface characteristics was applied to a molten KOH/NaOH wet chemical etching. The etching rate by molten KOH/NaOH wet chemical etching method was slower than that by conventional etching methods, such as phosphoric and sulfuric acid etching, which may be due to the formation of insoluble coating layer. Therefore, the molten KOH/NaOH wet chemical etching is a better efficient method for the evaluation of etch pits density. The grown GaN single crystals were characterized by using X-ray diffraction (XRD) and X-ray rocking curve (XRC). The etching characteristics and surface morphologies were studied by scanning electron microscopy (SEM). From etching results, the optimum etching condition that the etch pits were well independently separated in space and clearly showed their shape, was $410^{\circ}C$ and 25 min. The etch pits density obtained by molten KOH/NaOH wet chemical etching under optimum etching condition was around $2.45{\times}10^6cm^{-2}$, which is commercially an available materials.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.643-649
• /
• 2012

Coatings composited with alumina and Perfluoro alkoxyalkane (PFA) resin were deposited on stainless steel plate (SUS304) to further improve corrosion resistance. Plate (ca. $10{\mu}m$) and/or nanosize (27~43 nm) alumina used as inorganic additives were mixed in PFA resin to make alumina-fluoro composite coatings. These coatings were deposited on SUS304 plate with wet spray coating and then the film was cured thermally. According to the amount and ratio of the two kinds of alumina having plate morphology and nano size, corrosion resistance of the film was evaluated under strong acids (HF, HCl) and a strong base (NaOH). The film prepared with the addition of 5~10 wt% alumina powders in PFA resin showed corrosion resistance superior to that of pure PFA resin film. However, for the film prepared with alumina content above 10 wt%, the corrosion resistance did not improve with the physical properties, such as surface hardness and adhesion. The film prepared with plate/nanosize (weight ratio = 1/2) alumina especially enhanced the surface hardness and corrosion resistance. This can be explained as showing that the plate and the nanosize alumina dispersed in PFA resin effectively suppressed the penetration of cations and anions due to the long penetration length and fewer defects that accompany the improved surface hardness under a serious environment of 10% HF solution for over 120 hrs.

• Membrane Journal
• /
• v.10 no.3
• /
• pp.130-138
• /
• 2000

Polyethersulfone (PES) asymmetric membranes for gas separation were prepared by dry/wet phase inversion method and their separation properties for CO$_2$ and N$_2$ gases were investigated. The effects of important variables such as composition of casting solution and evaporation time in preparation of asymmetric gas membrane on membrane morphology and the separation properties were analyzed and the optimum condition of membrane preparation was established. To compensate the defects like pinholes existed on skin layer of the membrane prepared, the membranes were coated with silicone resin. By comparing separation properties after coating with those before coating, we found that the coating of silicone resin was effective to enhance the separation properties. The casting solution mainly used in this study consisted of PES, N-methyl-2-pyrrolidone, acetone, ethanol and distilled water was used as coagulation agent. It was shown that the selectivity for CO$_2$/N$_2$ was getting higher but the permeability decreases, as the contents of PES and volatile organic solvent and evaporation time increased. The selectivity for CO$_2$/N$_2$ and permeability of CO$_2$ of the membrane prepared under the optimum condition were found to be 61 and 21 GPU, respectively.

• Composites Research
• /
• v.29 no.4
• /
• pp.161-166
• /
• 2016

Carbon nanotube buckypaper (CNTs-BP)/thermoplastic polyurethane (PU) elastomer composites were successfully fabricated. The CNTs-BP/PU nanocomposites exhibited simultaneous improvements in both tensile modulus and strength by 1360 and 430%, respectively, as compared to pure PU. Possible reinforcing mechanisms were evidenced by SEM analyses and tensile tests. The CNTs-BP/PU nanocomposites can be potentially used as an inter-reinforcing agent in ultra-lightweight, high-strength aircraft, carbon-fiber-reinforced plastics, etc.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.88-88
• /
• 2017

Zn코팅은 우수한 내식성과 경제성을 바탕으로 자동차나 건축자재 등 산업의 전반적인 분야에서 광범위하게 사용되고 있다. 하지만 최근 한정된 Zn의 매장량으로 인한 원자제의 가격상승과 습식 도금과정의 환경오염 물질 배출 문제가 기존 Zn 코팅의 약점으로 지적되고 있다. 따라서 새로운 원소의 첨가로 인한 Zn의 사용량 감소나 친환경적인 공정방법을 적용하는 연구가 대두되고 있다. 최근의 연구 결과에 따르면 Zn-Mg 합금이 다른 Zn계 합금에 비해 내식성이 우수하며, 이와 같은 우수한 내식성은 $Mg_2Zn_{11}$, $MgZn_2$와 같은 Mg-Zn 이원계의 합금상에 의한 것으로 알려져 있다. 따라서 본 연구에서는 친환경적인 비대칭 마그네트론 스퍼터 공정을 활용하여 다양한 공정조건 하에서 Zn-Mg 박막을 합성하여 최적의 공정 조건을 도출하고자 하였다. Zn-Mg 박막 합성 시 Mg타겟의 조성은 3~10 wt.%로 변화하였으며 Zn-Mg 합금 타겟의 온도를 제어하여 박막의 Mg 조성과 타겟 온도가 Zn-Mg 도금강의 내식성 및 밀착성에 미치는 영향을 평가하였다. 합성된 Zn-Mg 박막은 FE-SEM, EDS, XRD를 사용하여 미세조직, 두께, Mg 조성, 합금상 등을 분석하였으며, 염수분무시험 및 0T 굽힘 시험을 활용하여 Zn-Mg 박막의 내식성 및 내식성을 비교 분석하였다. FE-SE및 EDS분석 결과 Zn-Mg 박막의 Mg 조성은 합금 타겟의 조성이 증가함에 따라 증가하였으며, Mg 함량이 증가할수록 미세구조가 치밀하게 변화하였다. 또한 Zn-Mg 박막 합성 중 타겟의 온도가 상승할수록 박막의 치밀도는 감소하였다. XRD분석 결과 박막을 이루는 주요 합금상은 Zn상과 $Mg_2Zn_{11}$상이며 본 연구에서는 증착 조건에 따른 합금상의 큰 변화는 보이지 않았다. 염수분무실험 및 밀착성 평가 결과 박막의 미세조직이 치밀할수록 Zn-Mg 도금강의 내식성은 향상되었으나, 밀착성은 오히려 감소하는 경향을 나타내었다. 이러한 결과는 Zn-Mg 박막이 치밀한 미세구조일수록 부식환경에서의 강판에 대한 보호 효과는 증가하는 반면, 변형 시 박막의 파괴로 인한 박리 현상이 가속되기 때문으로 판단된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.186-186
• /
• 2011

태양전지의 효율을 증가시키기 위해서는 표면에서의 Fresnel 반사를 줄여 입사된 빛이 흡수층까지 잘 도달되도록 해야 한다. 그러나 결정질 실리콘의 경우, 굴절률이 높아 32% 이상의 표면반사율을 보이고 있어, 실리콘 태양전지 표면에 단일 또는 다중 박막의 무반사 코팅을 통해 반사율을 낮추는 방법이 널리 사용 되어 오고 있었다. 하지만, 이와 같은 코팅 방법은 열적팽창 불일치, 물질 선택의 어려움뿐만 아니라 낮은 반사율을 포함하는 파장 및 빛의 입사각 영역의 제한 등 여러 문제점을 지니고 있다. 이러한 문제점을 보완하기 위해, 표면에 서브파장의 주기를 갖는 나노구조(subwavelength structure, SWS)의 형성에 관한 연구가 활발히 진행되고 있다. 습식 식각보다 건식 식각을 이용한 SWS 제작 방법이 표면 profile을 제어하기 용이하나 패턴 형성을 위해 식각 마스크가 필요하다. 최근, 복잡하고 고가의 전자빔 또는 나노임프린트를 이용한 패턴 형성보다, 간단/저렴하며 대면적 제작이 용이한 금속 나노입자 마스크를 이용한 SWS의 제작에 대한 연구가 활발히 진행되고 있다. 또한 SWS의 무반사 특성은 표면 profile에 따라 크게 영향을 받는다. 따라서 본 실험에서는 열적 응집현상에 의해 형성되는 self-assembled Pt 나노입자 식각 마스크 및 $SiCl_4$가스를 사용한 유도결합 플라즈마(inductively coupled plasma, ICP) 장비를 이용하여 무반사 실리콘 SWS를 제작하였으며, SWS 표면 profile에 따른 구조적 및 무반사 특성을 조사하기 위해 다양한 공정조건을 변화시켰다. 실리콘 기판 위의 Pt 박막은 전자빔 증착(e-beaml evaporation)법을 사용하였고, 급속 열처리(RTA)를 통해 Pt 나노입자의 식각 마스크를 형성시켰다. Pt 나노입자들의 패턴 및 제작된 무반사 실리콘 SWS의 식각 profile은 scanning electron microscope를 사용하여 관찰하였으며, UV-VIR-NIR spectrophotometer를 사용하여 350~1050 nm 파장 영역에서의 반사율을 측정하였다. ICP 식각 조건을 변화시켜 5% 이하의 낮은 반사율을 갖는 높이가 높고 쐐기 형태의 실리콘 SWS를 도출하였다.