• 대한기계학회논문집
• /
• 제14권6호
• /
• pp.1487-1494
• /
• 1990

본 연구에서는 공기분자간 평균 자유비형거리(molecular mean free path)를 고려한 수정된 레이놀즈 방정식을 공기막 두께의 미소 교란항에 대하여 전개하여 비선 형 정적 평형방정식과 교란 미분방ㄹ정식을 구하였다. 비선형 정적 평형방정식을 슬 라이더의 정량적인 거동형태를 표시하므로 이를 이용하여 슬라이더의 정적특성을 구할 수 있다. 이에 반하여, 동적 교란미분 방정식은 슬라이더의 간극함수에 대한 각종 교란에 의하여 유발되는 반발압력을 정성적으로 나타내므로, 슬라이더의 외부교란에 대한 응답특성 및 자기복원특성 등을 구할 수 있다. 이러한 특성을 서스펜션에 부착 된 헤드 시스템의 운동방정식에 함께 고려하여 시스템의 동적 특성을 해석하고 슬라이 더의 설계변수가 이에 미치는 영향을 고찰하고저 한다.

• 대한기계학회논문집A
• /
• 제24권6호
• /
• pp.1520-1528
• /
• 2000

This study presents a method for determining bearing stiffness and damping coefficients of air-lubricated slider bearing, and shows influences of air-bearing surface geometry(recess depth, crown an d pivot location) on flying attitude and dynamic characteristics. To derive the dynamic lubrication equation, the perturbation method is applied to the generalized lubrication equation which based on linearized Boltzmann equation. The generalized lubrication equation and the dynamic lubrication equation are converted to a control volume formulation, and then, the static and dynamic pressure distributions are calculated by finite difference method. The recess depth and crown of the slider show significantly influence on flying attitude and dynamic characteristics comparing with those of pivot location.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.1117-1121
• /
• 2001

The dynamic behavior of slider is investigated using Dynamic Flying Height Tester(DFHT). The dependence of slider's dynamic fluctuation on disk velocity is measured, and a comparison is made with the computational result.

• 대한기계학회논문집A
• /
• 제27권3호
• /
• pp.343-348
• /
• 2003

In this study, optimum designs of the air-bearing surface (ABS) are achieved using the reduced basis concept which can effectively reduce the number of design variables without cutting down on the design space. Even though the optimization method is easier and more applicable to handle than the trial-and-error method, its efficiency is largely dependent on the number of the design variables. Hence, the reduced basis concept is applied, by which the desired design can be defined as a linear combination of basis designs. The simulation results show the effectiveness of the proposed approach by obtaining the optimum solutions of the sliders whose target flying heights are 25, 20, and 15nm.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.52-57
• /
• 2001

In this paper, the optimum designs of air-bearing surface(ABS) are achieved effectively by using reduced basis concept which can reduce the number of design variables although the design space is distended. Generally, the optimization method is more effective than the trial and error. However, the efficiency of the former is largely dependent on the number of the design variables. In order to reduce the number of design variables and increase the efficiency, reduced basis concept is applied. We can define the desired design as a linear combination of basis designs using this concept. From this optimization method with reduced basis concept, we easily obtain the optimum designs of ABS whose target flying heights are 25, 20, 15 nm.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1561-1569
• /
• 2000

Flying attitudes of the slider, which are flying height, pitch and roll, are affected by the air flow velocity, the skew angle, and the manufacturing tolerances. Traditional designs of the air bearing surface have considered only the flying performances for the variations in the air flow velocity and the skew angle, which are determined by the radial position. In this study, we present the new shape design of the air bearing surface by considering the track seek performance and the air bearing stiffness as well as the traditional design requirements. The optimization technique is used to improve the dynamic characteristics and operating performance of the newly proposed air bearing surface shape design further. The optimized configuration is obtained automatically and the optimally designed sliders show the enhanced flying and dynamic characteristics.

• 한국기계가공학회지
• /
• 제16권5호
• /
• pp.119-125
• /
• 2017

In this paper, the characteristics and load carrying capacity of square pocket surfaces on a slider bearing are discussed for the thin film effect by the square pocket slider bearing. To study the lubrication, a Reynolds equation is used in this paper for the analysis of the slider bearing characteristics with square pocket surfaces. For numerical analysis, the central differencing scheme finite difference method is used. In a slider bearing with square pocket surfaces, the simulation dependent parameters such as pressure and load carrying capacity of the bearing can be acquired from the independent parameters, the slope of the slider bearing and number of pockets on the upper slider. These results can be acquired by the programmed softwar,e and they can be analyzed and stored in a sequential data file for later analysis. Furthermore, their pressure and load capacity distribution can be displayed easily by using the developed program with the Matlab GUI.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.316-321
• /
• 2001

The optical storage device has recently experienced significant improvement, especially for the aspects of high capacity and fast transfer rate. However, it is necessary to study a new shape of air bearing surface for the rotary type actuator because the optical storage device has the lower access time than that of HDD (Hard Disk Drives). In this study, we proposed the air bearing shape by using SA (Simulated Annealing) algorithm which is very effective to achieve the global optimum instead of many local optimums. The objective of optimization is to minimize the deviation in flying height from a target value 100nm. In addition, the pitch and roll angle should be maintained within the operation limits.

• 한국산학기술학회논문지
• /
• 제8권6호
• /
• pp.1319-1324
• /
• 2007

입출력 헤드 구조의 형상을 정확하게 조절할 수 있는 기술은 하드디스크 드라이브의 성능에 결정적인 요소이다. 본 논문에서 연구한 슬라이더는 알루미나 티타늄 카아바이드로 구성되었으며 디스크를 통과할 때 공기 베어링 역할을 한다. 그러므로 슬라이더의 곡률을 조절하는 것은 매우 중요하다. 본 연구에서 곡률을 조절하기 위해 헤드 슬라이더에 잔류응력을 발생시켜 곡률을 생성하는 레이저 화선 시스템이 사용된다. 슬라이더 형상의 조절을 강화하기 위해 화선(scribe)의 형상에 따른 곡률을 예측할 수 있는 방법이 중요하다. 레이저 화선과 유사한 효과를 얻을 수 있는 응력을 발생하는 하중계를 유한요소 모델에 적용한다. 하중계에 의해 형성된 곡률은 측정값을 통해 보정된다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1992년도 제15회 학술강연회초록집
• /
• pp.60-65
• /
• 1992

액정은 합성에 의해서 만들어지는 고분자 화합물로서 액체와 고체결정의 중간적인 특성을 갖는 물질이다. 따라서 액체와 같이 점도를 갖고 유동하며 고체와 같이 외부하중에 대하여는 탄성변형을 하므로 일반 윤활유보다 월등한 윤활특성이 기대된다. 액정은 분자배열에 따라 smectics, cholesterics, Nematics의 세종류로 나뉘어지며 Smectics는 다시 Smectic A, Smectic C등으로 분류되며 관심대상은 Smectic A이다. 본 연구에서는 평판 슬라이더 베어링의 간극에 액정층이 형성되어있을때 액정의 탄성계수, 침투계수 및 벌어짐계수가 베어링부하, 액정층의 유동현상등에 미치는 영향을 비선형 유한 요소법을 사용하여 해석하고 레이놀즈 이론해와 비교하였다.