• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1487-1494
• /
• 1990

In this paper the dynamic characteristics of self acting air lubricated slider bearing of hard disk/head system are investigated. The dynamic equations of magnetic head mechanism considering both parallel and pitch motion and the time dependent modified Reynolds equation are analyzed and the dynamic pressure distribution of air film is numerically calculated in frequency domain by small perturbation method and finite difference scheme with variable grid. The dynamic response of the slider spacing is obtained accordingly as the moving recording surface vibrates in parallel mode.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.6 s.177
• /
• pp.1520-1528
• /
• 2000

This study presents a method for determining bearing stiffness and damping coefficients of air-lubricated slider bearing, and shows influences of air-bearing surface geometry(recess depth, crown an d pivot location) on flying attitude and dynamic characteristics. To derive the dynamic lubrication equation, the perturbation method is applied to the generalized lubrication equation which based on linearized Boltzmann equation. The generalized lubrication equation and the dynamic lubrication equation are converted to a control volume formulation, and then, the static and dynamic pressure distributions are calculated by finite difference method. The recess depth and crown of the slider show significantly influence on flying attitude and dynamic characteristics comparing with those of pivot location.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.1117-1121
• /
• 2001

The dynamic behavior of slider is investigated using Dynamic Flying Height Tester(DFHT). The dependence of slider's dynamic fluctuation on disk velocity is measured, and a comparison is made with the computational result.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.3
• /
• pp.343-348
• /
• 2003

In this study, optimum designs of the air-bearing surface (ABS) are achieved using the reduced basis concept which can effectively reduce the number of design variables without cutting down on the design space. Even though the optimization method is easier and more applicable to handle than the trial-and-error method, its efficiency is largely dependent on the number of the design variables. Hence, the reduced basis concept is applied, by which the desired design can be defined as a linear combination of basis designs. The simulation results show the effectiveness of the proposed approach by obtaining the optimum solutions of the sliders whose target flying heights are 25, 20, and 15nm.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.52-57
• /
• 2001

In this paper, the optimum designs of air-bearing surface(ABS) are achieved effectively by using reduced basis concept which can reduce the number of design variables although the design space is distended. Generally, the optimization method is more effective than the trial and error. However, the efficiency of the former is largely dependent on the number of the design variables. In order to reduce the number of design variables and increase the efficiency, reduced basis concept is applied. We can define the desired design as a linear combination of basis designs using this concept. From this optimization method with reduced basis concept, we easily obtain the optimum designs of ABS whose target flying heights are 25, 20, 15 nm.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1561-1569
• /
• 2000

Flying attitudes of the slider, which are flying height, pitch and roll, are affected by the air flow velocity, the skew angle, and the manufacturing tolerances. Traditional designs of the air bearing surface have considered only the flying performances for the variations in the air flow velocity and the skew angle, which are determined by the radial position. In this study, we present the new shape design of the air bearing surface by considering the track seek performance and the air bearing stiffness as well as the traditional design requirements. The optimization technique is used to improve the dynamic characteristics and operating performance of the newly proposed air bearing surface shape design further. The optimized configuration is obtained automatically and the optimally designed sliders show the enhanced flying and dynamic characteristics.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.5
• /
• pp.119-125
• /
• 2017

In this paper, the characteristics and load carrying capacity of square pocket surfaces on a slider bearing are discussed for the thin film effect by the square pocket slider bearing. To study the lubrication, a Reynolds equation is used in this paper for the analysis of the slider bearing characteristics with square pocket surfaces. For numerical analysis, the central differencing scheme finite difference method is used. In a slider bearing with square pocket surfaces, the simulation dependent parameters such as pressure and load carrying capacity of the bearing can be acquired from the independent parameters, the slope of the slider bearing and number of pockets on the upper slider. These results can be acquired by the programmed softwar,e and they can be analyzed and stored in a sequential data file for later analysis. Furthermore, their pressure and load capacity distribution can be displayed easily by using the developed program with the Matlab GUI.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.316-321
• /
• 2001

The optical storage device has recently experienced significant improvement, especially for the aspects of high capacity and fast transfer rate. However, it is necessary to study a new shape of air bearing surface for the rotary type actuator because the optical storage device has the lower access time than that of HDD (Hard Disk Drives). In this study, we proposed the air bearing shape by using SA (Simulated Annealing) algorithm which is very effective to achieve the global optimum instead of many local optimums. The objective of optimization is to minimize the deviation in flying height from a target value 100nm. In addition, the pitch and roll angle should be maintained within the operation limits.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.6
• /
• pp.1319-1324
• /
• 2007

Accurately controlling the shape of the read/write head structure is critical in the performance of a modem hard disk drive. The sliders investigated are composed of alumina and titanium carbide(AITiC) and act as an air bearing when passing over the disks. Controlling the curvature of the slider is of primary importance. A laser scribing system that produces curvature by inducing residual stress into the slider can be utilized. Predicting the curvature created by a pattern of scribes is of great importance to increase the control over the sliders' shape. The force system that produces stresses similar to the laser scribing is applied to the finite element analysis model. The curvatures created by the force system are calibrated to experimental measurements.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1992.06a
• /
• pp.60-65
• /
• 1992

액정은 합성에 의해서 만들어지는 고분자 화합물로서 액체와 고체결정의 중간적인 특성을 갖는 물질이다. 따라서 액체와 같이 점도를 갖고 유동하며 고체와 같이 외부하중에 대하여는 탄성변형을 하므로 일반 윤활유보다 월등한 윤활특성이 기대된다. 액정은 분자배열에 따라 smectics, cholesterics, Nematics의 세종류로 나뉘어지며 Smectics는 다시 Smectic A, Smectic C등으로 분류되며 관심대상은 Smectic A이다. 본 연구에서는 평판 슬라이더 베어링의 간극에 액정층이 형성되어있을때 액정의 탄성계수, 침투계수 및 벌어짐계수가 베어링부하, 액정층의 유동현상등에 미치는 영향을 비선형 유한 요소법을 사용하여 해석하고 레이놀즈 이론해와 비교하였다.