• Journal of Energy Engineering
• /
• v.19 no.4
• /
• pp.221-227
• /
• 2010

In this study, we consider gas generation characteristics on pyrolysis of eco-fuel which were made by mixing of Pitch Pine and Lauan sawdust as biomass and polyethylene, polypropylene, polystyrene as municipal plastic wastes with catalyst in fixed bed reactor. From the result of higher heating value(HHV) measurement and of ultimate analysis, the heating value of plastic wastes and a hydrogen content in plastic sample are higher than biomass. An activation energy was reduced by a catalyst addition. However the catalyst content influence over 5 wt% was insignificant. The yield of hydrogen from gasification of biomass containing plastic wastes such as polyethylene, polypropylene and polystyrene were obtained higher than that of sole biomass. The high temperature and mixture ratio of catalyst conditions induced to high hydrogen yield in most of the samples. As the influence of catalyst, the hydrogen yield by catalytic reaction was higher than non-catalytic reaction. We confirmed that Ni-$ZrO_2$ catalyst is more active in increasing the hydrogen yield in comparison with that of carbonate catalyst. The maximum hydrogen yield was 65.9 vol.%(Pitch Pine / polypropylene / 20 wt.% Ni-$ZrO_2$(1:9) at $900^{\circ}C$).

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.19-19
• /
• 2009

최근, 유한한 에너지 자원의 한계와 지구 온난화 등으로 세계의 제조 산업은 새로운 국면을 맞이하고 있으며, 특히, 자동차 산업은 화석연료를 주 에너지원으로 사용한다는 점과 이 연료를 연소시킬 때 발생하는 이산화탄소가 지구 온난화의 주된 원인이 될 수 있다는 점에서 상기 문제들을 해결하기 위한 다양한 방법에 주목하고 있다. 그 중에서 자동차의 생산기술 측면에서 볼 때, 가장 중요한 이슈는 차체 경량화다. 자동차 차체는 자동차를 구성하고 있는 여러 가지 부품 중에서 약 40% 정도의 무게 비율을 차지하고 있기 때문에, 차체 경량화는 연비향상과 이산화탄소 배출가스 감소와 직접적인 관계를 가지고 있다. 다양한 차체 경량화 방법 중에서 가장 쉽게 접근할 수 있는 방법이 경량소재 적용에 의한 경량화 방법이다. 현재, 탄소섬유 강화 플라스틱과 같이 무게 절감 비율을 최대화 할 수 있는 소재들도 개발되어 일부 적용되고 있지만, 일반적으로 차체 경량화 소재로 가장 널리 사용되고 있는 소재는 알루미늄 합금이며, 이에 대한 차체 적용 비율이 점차로 높아지는 추세에 있다. 이에, 본 연구에서는 알루미늄 합금이 차체에 적용되었을 때의 장단점을 살펴보고, 알루미늄 합금을 적용한 차체 생산과정에서 유의해야 될 사항들과 이를 바탕으로 하는 생산성 극대화 방안에 대하여 고찰하였다. 먼저, 기존의 알루미늄 저항 점 용접공법의 단점을 최소화하고 대량생산 체계에 적합하도록 개발된 새로운 개념의 저항 점 용접 시스템에 대해 그 성능과 양산성을 검증하였다. 구리 전극과 알루미늄 피용접물 사이에 프로세스 테이프를 삽입하여 용접하는 이 시스템은 열전도성이 큰 알루미늄 용접부에서 저전류의 조건에서도 효과적으로 균일한 발열현상이 발생하게 하였으며, 전극 팁 드레싱 없이 모든 용접점이 항상 동일한 조건에서 용접이 이루어질 수 있도록 하였다. 용접 조건 설정에 있어서도 용접전류가 통전되는 순간에 전극 가압력을 자유로이 변형시켜 용접부 크랙 발생을 최소화할 수 있음을 확인하였다. 알루미늄의 또 다른 대표적인 접합방법인 아크용접에 있어서는 용접 입열량을 조절하여 용접변형을 최소화 할 수 있는 아크용접 시스템에 대해 양산성과 적용 타당성을 검토하였다. 와이어 송급 방향을 자유자재로 바꿀 수 있는 이 시스템의 특성에 의해 스패터를 최소화하면서 용융금속이 효과적으로 모재에 금속이행 될 수 있음을 확인하였으며, 판재, 압출재, 및 다이캐스팅재 등 다양한 차체 소재에 대한 용접 가능성 및 미그-레이저 하이브리드 용접과의 비교분석을 통하여 차체 박판 용접에서도 최소의 열변형으로 효과적으로 사용될 수 있음을 보였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.4
• /
• pp.419-425
• /
• 2014

This study applied finite element analysis (FEA) to the body frame of the 200-meter class multi-legged subsea walking robot known as Crabster (CR200). The body frame of the CR200 is modeled after the ribcage of a human so that it can disperse applied external loads. It is made of carbon-fiber-reinforced plastic (CFRP). Therefore, the frame is lighter and stronger than it would be if it were made of other conventional materials. In order to perform FEA for the CFRP body frame, we applied the material properties of the CFRP as obtained from a specimen test to an FE model of CFRP frame. Finally, we performed FEA with respect to the load conditions encountered when the robot is launched into and recovered from the sea. Also, we performed FEA for the frame, assuming that it was fabricated using a conventional material, in order to compare its characteristics with CFRP.

• Fire Science and Engineering
• /
• v.32 no.4
• /
• pp.75-85
• /
• 2018

The Grenpell tower fire in England in June of 2016 is a representative example of damage caused by a vertical fire spreading through external insulation. Organic insulation materials, which are widely used in external insulation, have the disadvantage that they have good insulation performance but are vulnerable to fire. Aluminum composite panels are used as exterior wall finishing materials, and plastics used in aluminum are regarded as the cause of vertical fire spread. Due to the steel frame used to secure the aluminum composite panel to the outer wall, a cavity is formed between the outer wall and outer wall finish. When a fire occurs on the outer wall, the flammable outer wall as well as the flame generated from the heat-insulating material spreads vertically through the cavity, resulting in damage to people and property. In Korea, material unit performance tests are carried out by the Ministry of Land, Infrastructure and Transport notice 2015 - 744. However, in the UK, the BS 8414 test is used to measure the vertical fire spreading time on the outer wall in real scale fire tests. In this study, the risk of external wall fire was evaluated in an actual fire by conducting a real scale wall fire test (BS 8414), which was carried out in Europe, using aluminum composite panels of semi-noncombustible materials suitable for current domestic standards. The purpose of this study was to confirm the limitations of material unit evaluation of finishing materials and to confirm the necessity of introducing a system to prevent the spread of outer wall fire through an actual scale fire test.

• Journal of Conservation Science
• /
• v.33 no.5
• /
• pp.363-370
• /
• 2017

The aim of this study was to obtain information about two early-20th Century clothes, for which the "National Memorial Museum of Forced Mobilization under Japanese Occupation" has sought to receive preservation treatment. Optical microscopes and a scanning electron microscope were used to investigate the weaving of the clothes, and Fourier transform infrared spectroscopy(FT-IR) was used to investigate the fibers. Cloth A is believed to be a Japanese half sleeved inner wear(Hanjuban) used by women. Cloth B is believed to be working clothing that was checked by an Osaka plant. This was verified by a book written by the Japanese army. Both of the clothes were made mostly from cotton, although the inner wear also used viscose rayon on the neck collar. The button on the working wear was made of urea formaldehyde resin, an early precursor to plastic.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.596-605
• /
• 2016

In previous years, practice hand grenades were composed of non-degradable plastics and caused environmental pollution. Therefore, this study applied PLA(Polylactic acid) to practice hand grenades that would biodegradable within a short time. High expectations are being placed on PLA as a substitute for plastics because it can decompose to water and carbon dioxide. The aim of this study was to confirm that the PLA material of a practice hand grenade has biodegradability in a pilot-scale composting unit and estimate the applicability for other items. A composting test was progressed according to ISO 16929(2013). The test process was found to be valid. At the end of the composting test (after 12 weeks), the entire content of the test bin with the test sheet was sieved, sorted and analyzed. A disintegration percentage of 99.2% was obtained after 12 weeks of composting. Therefore, the 90% pass level required by ISO 17088(2013), EN 13432(2000), and ASTM D 6400-12 was easily reached. On the other hand, more research will be needed to determine additional applications of PLA material for consumables.

• Analytical Science and Technology
• /
• v.23 no.2
• /
• pp.216-223
• /
• 2010

In previous research, results on efficiency versus size and type of Ag particles showed similarity of detection efficiency comparing the particles of flake and spherical type with the gray particle on the market and in the case of nAg (rod, $0.9\;{\mu}m$) particle, relatively good results was given in the various evaluation methods for detection efficiency of latent fingerprint. However, oxidation was occurred when nAg particles laying on nature condition for a month and due to water absorption, detection efficiency was decreased. Therefore, with need to prevent oxidation and water absorption, more research is necessary. In this research, surface modification on nAg particles using silicon oil was conducted in various methods for complementing weakness of oxidation and water absorption. Then detection efficiency of nAg particles and surface modified nAg particles was evaluated by the number of feature points on the surface of non-porous materials (glass, plastic etc.) and degree of particle adhesion with ridges and contrast of detected fingerprint. Improvement of preventing oxidation and water absorbtion was given by surface modification using silicon oil (DC200, 0.5%) on the surface of non-porous materials.

• Analytical Science and Technology
• /
• v.30 no.5
• /
• pp.234-239
• /
• 2017

Identifying the components of residues that are not completely burned at the sites of fires site can provide valuable information for tracing the causes of fires. In order to clarify the types of plastic combustion residues found at the scenes of fires, we studied the residue formed after the combustion of polyethylene (PE) and acrylonitrile butadiene styrene (ABS). Plastic samples were burned at 200, 300, 350, 400, and $500^{\circ}C$ for 3 min using a cone calorimeter, and the changes in weight and combustion products were observed. The powder products obtained by lyophilization and pulverization of the combustion products obtained at each temperature were analyzed by a Fourier transform-near infrared (FT-NIR) spectrometer. When the PE samples were burned, the weight did not change up to $350^{\circ}C$, however a significant change in the weight could be measured above $400^{\circ}C$. The principal component analysis (PCA) of the FT-NIR spectra of the PE and ABS samples obtained at each temperature confirmed that the combustion residues at each temperature were PE and ABS, respectively. Therefore, the types of unburned plastics found at the sites of fires can be confirmed rapidly by near infrared spectroscopy.

• Journal of Life Science
• /
• v.16 no.6
• /
• pp.972-977
• /
• 2006

The purpose of this study was to investigate the effects of combined exercise and green tea intake on body weight and adiponectin in obese female high school students. The thirty six(36) subjects were U women's high school students in U city and they were classified into four groups; exercise group), green tea group, exercise & green tea group and control group. All the subjects being obese with more than $27\;kg/m^2$. The exercise program was conducted with combined exercise of walking and the use of dumbbells. While walking having a $55{\sim}75%$HRmax intensity and uging $1{\sim}2\;kg$ dumbbell for $60{\sim}70$ minutes four times a week during 12 weeks. Subjects had one stick (0.8g green tea powder) four times a day during 12 weeks. The conclusions of this study are as follows. 1) For the level of body weight, in comparison within each group, EG, GG and EGG significantly decreased in body weight and in the comparison between groups, EG and EGG significantly decreased more in body weight than GG and CG after 12 weeks intervention. 2) For the level of adiponectin, in the comparison within each group, EG, GG, EGG didn't show any difference in adiponectin after 12 weeks intervention. However, CG significantly decreased in adiponectin and in the comparison between groups, EG and EGG significantly increased in adiponectin than CG after 12 weeks intervention.

• Korean Journal of Food Science and Technology
• /
• v.35 no.5
• /
• pp.877-883
• /
• 2003

Multi-degradable master hatch (M/B) was prepared and 0.05 mm polyethylene (PP) food packaging films containing 0, 10, and 20% M/B were manufactured by inflation film processing. The films were exposed to UV radiation, fungi, and heat in order to observe their photolysis, biodegradability, and thermal degradability, respectively. While pure PP film maintained more than 70% of its original elongation after 8 weeks of UV radiation, an almost perfect loss in the elongation of PP film containing 20% M/B was observed. Significant decreases in elongation of PP films by heat treatment $(68{\pm}2^{\circ}C)$ were also found in samples containing the multi-degradable M/B. By observing changes in film surface after the inoculation of fungi using scanning electron microscopy (SEM), the biodegradability of plastic film could be accelerated with the addition of multi-degradable M/B. The results of the mulching test in yard showed that adding multi-degradable M/B can effectively degrade plastic films in natural environmental conditions without interrupting the growth of plants.