• The Journal of the Acoustical Society of Korea
• /
• v.4 no.2
• /
• pp.56-63
• /
• 1985

마이크로스트립선로의 특성파라메타 분석을 위한 새로운 방법이 제안되었다. 마이크로스트립선 로의 특성파라메타들은 최소자승법에 의해서 계산하였고, 이 방법에 의해 마이크로스트립선로의 구조와 차원에 따른 결과를 보였다. 이들 결과를 차분법에 의해서 얻어진 결과와 비교 검토하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.58-59
• /
• 2011

Microstrip line on dielectric substrate depending on the type of its configuration can be applied to be antenna, communication filters, and resonators. When driving frequency is considered more than X-band, unnecessary signal leakage should be occurred because of flowing through the planar circuit at banding position. So leakage signal will affect other planar circuit, and then EMC problem has to be introduced. In this paper, the affection of banding planar circuit on dielectric substrate was investigated.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.63-64
• /
• 2015

In this paper, a microstrip array antenna capacitively coupled to a microstrip line is studied. The array antenna consists of uniformly spaced rectangular microstrip patches arranged close to a feeding microstrip line on a grounded dielectric substrate. The effects of various parameters, such as strip width and length, distance between adjacent patches, gap between strip patches and microstrip feed line, on the antenna performance were examined. By properly adjusting geometrical parameters, the array suitable for a high gain antenna for use in a frequency band centered at 12.5 GHz was designed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.3
• /
• pp.457-463
• /
• 2016

In this paper, a method of enhancing the bandwidth of a double-dipole quasi-Yagi antenna (DDQYA) using a modified integrated balun is presented. The modified integrated balun consists of a microstrip (MS) line inserted along the center of a coplanar strip (CPS) line and the end of the MS line is connected to the CPS line through a shorting pin at the feed point. The geometry of the modified integrated balun is adjusted to improve the bandwidth of the DDQYA. In addition, the performance of the proposed balun in a back-to-back configuration is compared with a conventional balun. The proposed antenna with the optimized modified integrated balun is fabricated on an FR4 substrate, and the experiment results show that the antenna has a frequency band of 1.56-3.04 GHz(64.4%) for a VSWR < 2, which shows enhanced bandwidth compared to the DDQYA with the conventional balun.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.9
• /
• pp.1949-1956
• /
• 1997

The mode parameters of asymmetrical coupled microstrip lines on composite substrates are derived by using closed form expression. A 10 dB directional couplers, where the center frquency is 1.8 GHZ, are fabricated on a single-layer substrate and on compsite substrates respectively. It is shown that coupler on a single-layer substrate.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.576-579
• /
• 2007

마이크로스트립으로 급전되는 슬롯 안테나를 소형화하기 위해 폴디드 슬롯과 T형 마이크로스트립 선로로 구성된 안테나 구조를 제안하였다. 전형적인 마이크로스트립으로 급전된 슬롯 안테나와 성능(안테나 크기, 슬롯 길이, 대역폭 등)을 비교하였으며, T형 마이크로스트립선로를 이용한 급전선로의 임피던스정합 방법에 대하여 설명하였다. 제안된 구조로 유전제기판상에 2.45GHz 대역 WLAN용 안테나를 설계 및 제작하였으며 특성 실험(반사손실, 부사패턴)을 통해 연구의 타당성을 확인하였다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12B
• /
• pp.1724-1732
• /
• 2001

In this paper, a technique for increasing the bandwidth of microstrip array antennas using the parallel coupled lines on a single layer is presented. Four types of wideband microstrip array antenna are designed and the characteristics of each type are analyzed. In addition, an iterative method using a distributed network is proposed to design the parallel coupled lines as a wideband impedance matching network. Measurements show that the proposed antennas provide wider bandwidths ∼1.7 times those of conventional microstirp array antennas, while the sizes of proposed antennal are the same as that of a conventional array. And low cross-polarization level can be obtained through symmetrical locations of the parallel coupled lines section

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.6 s.121
• /
• pp.680-688
• /
• 2007

Time domain closed-form analytical solutions to the coupled telegrapher's equations for the voltage and current on a lossless multiconductor transmission line are presented. The resulting expressions are obtained in the form of exact time domain propagators operating on the line voltage and current. Time domain numerical methods are developed and examples showing exceptionally accurate results are obtained for uniform and nonuniform; symmetric and asymmetric strip lines.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.3
• /
• pp.565-573
• /
• 2000

In this paper, a interdigital microstrip bandpass filter is designed. A interdigital microstrip bandpass filter has many advantages such as insertion return loss, lower return loss, higher frequency selectivity and smaller in size in comparison with the conventional coupled line filter. A interdigital microstrip bandpass filter consists of quasi TEM-mode strip line resonators between parallel ground plant. Each resonator element is a quarter wavelength long of the center frequency and is short circuited at one end and open circuited at the other end. In the filter design, Ensemble software is used. Experimental results show that the bandwidth of interdigital microstrip bandpass filter is 2.52GHz, insertion loss is -1.8dB and return loss is -17.0dB at 11.20Hz.

• Journal of the Korea Society of Computer and Information
• /
• v.3 no.3
• /
• pp.107-112
• /
• 1998

In this paper, filter designed and produced to use hi-Z low-Z filter which is easy to produce microstrip line and uses space less than used stub filter. This filter has very short electrical length of lines, that is Bl＜$\pi$/4, lowpass prototype series inductor replaced high impedance line section and shunt capacitance replaced low impedance line section. Replaced each section designed microstrip lines and effective permittivity of the given microstrip calculated and each section width and length calculated dna filter used design. Designed filter compared the theory value of touchstone with the experiment value of real produced filter and an analyzed response charictristic.