• Fire Science and Engineering
• /
• v.30 no.1
• /
• pp.24-30
• /
• 2016

Autoignition characteristic is an important factor of all combustible substances, and a critical determinant in assessing the effectiveness of fire hazard prevention. This study investigated the autoignition characteristic of mixtures of Ethylene Glycol and water using an ASTM D2155 type ignition temperature measuring apparatus. It was possible to get the minimum temperature as $434^{\circ}C$ from 100% Ethylene Glycol within range of $75{\sim}160{\mu}l$. A volume of $100{\sim}125{\mu}l$ of a mixed sample of Ethylene Glycol and water (80 : 20) was ignited at the same temperature ($434^{\circ}C$). Also it was possible to get the auto ignition temperature as $437^{\circ}C$ from a mixed sample of Ethylene Glycol and water (60 : 40) within range of $120{\sim}160{\mu}l$. The instantaneous ignition temperatures determined for $125{\mu}l$ of each of the three samples were $579^{\circ}C$, $595^{\circ}C$ and $611^{\circ}C$, respectively. Both auto ignition temperatures and instantaneous ignition temperatures were increased through the addition of water to the samples.

• Fire Science and Engineering
• /
• v.12 no.2
• /
• pp.61-68
• /
• 1998

According to the results for the thermodynamic stability of feed-stuff dust, there are little change of initiation temperature of heat generation and heating value for used particle size. But initiation temperature of heat generation decreased with high heating rate whereas decomposition heat increased with particle size. Using the supporting gas, O2, initiation temperature of heat generation decreased remarkably than using the inert gas, N2, and heating value increased as twenty times under the same condition. When the ignition energy is given from the outside, used fine particle which can float in the air easily reacted tremendously with oxygen. Average maximum explosion pressure was 6.88 Kgf/$\textrm{cm}^2$ for 80/100 mesh.

• Journal of the Korean Institute of Gas
• /
• v.18 no.3
• /
• pp.38-43
• /
• 2014

This paper is to analyze and study the failure examples of fire by inflammables and electric contact faulty in interior of vehicle. The first example, the driver used to air freshener that remove the air conditioner bad smell. He get out of a car. And then, he put it on the crash pad. Before long, a fire breaks out because of explosion solar radiation. The second example, the driver used in room of a car. It certified the fire by disconnection phenomenon happened the electric overload. The third example, the driver install the heat rays to warm his body, In the initial stages, it didn't seek the dangerous of fire during using a car to 5,000km. This heat rays become to down durability so that produced the electric overload in an instant. The fourth example, after the man smoked the cigarette on riding with rear seat, he put it on seat in vehicle no extinguishing the burning cigarette. It knew the fact that burnt to ashes a car by on well combustible paper. Thus, the driver must consider a countermeasure for minimize the fire production when he use the inflammable and install adding electric system.

• Fire Science and Engineering
• /
• v.26 no.6
• /
• pp.24-30
• /
• 2012

This study is on the method of the detection for flame and series arc which can be happened at poor contact point added a vibration in part of contact point of low voltage line. In general, the causes of electric fire are over current, short circuit, poor contact, ect. The over-current or short circuit among those causes is detected by measuring a instant current value, but poor contact is difficult to detect by measuring a excessive value of the voltage and current and a distortion of waveforms. And therefore, in this paper, it is studied on the optimal technique of the arc judgement using fuzzy logic and MDET (Multi Dimension Estimation Technique). And it carries out the simulation for arc detection and the experiment for controller and load test. In result, the controller and detection algoristhm, is classified with normal wave and abnormal arc wave without relation with each loads and so the controller can detect a series arc successfully.

• Fire Science and Engineering
• /
• v.29 no.4
• /
• pp.73-80
• /
• 2015

In this study, the conditions of explosion range of gasoline, which is used as combustion improver, are experimentally analyzed. Two types of compartment, which is the small scale ($0.5m{\times}0.5m{\times}1.0m$) and the middle scale ($0.5m{\times}0.5m{\times}1.0m$), are mocked-up and the auto-control systems are installed in order to measure the vaporized gasoline and the moment of pressure, ignition time and maximum pressure. In case the maximum flammable limit of gasoline is up to 22.4 Vol% not the generalized range of 1.4~7.6 Vol% when nichrome igniter of $700^{\circ}C$ is used. These results can be appled to the analytical prediction of fire identification in the field of explosion.

• Fire Science and Engineering
• /
• v.20 no.1 s.61
• /
• pp.1-5
• /
• 2006

The spontaneous ignition of a flammable matter is a crucial factor for the prevention of a fire. The minimum ignition temperatures of Gasoline and Cenox in $1000{\mu}l$ of a sample were determined to be $340.5^{\circ}C\;and\;368.5^{\circ}C$ respectively. In addition when the time taken for ignition was 1.0 sec, the instantaneous ignition temperatures were $416^{\circ}C\;and\;427^{\circ}C$ respectively. Moreover, the changes in the minimum ignition temperature were small when less than 60 v/v% of Cenox was added, but the changes were great when 80 v/v% or more was added. Therefore, it is hypothesized that, when used as a fuel in the Gasoline engine, the ratio of the mixture of Cenox and Gasoline will be a very important factor.

• Fire Science and Engineering
• /
• v.13 no.3
• /
• pp.19-26
• /
• 1999

$CO_2$ extinguishing system is the most $\phi$pular among the gas extinguishing system. $CO_2$ is usually stored with liquified state. But, it gasifies at the tip of nozzle when $CO_2$ was released through the pipe and head. A ro$\alpha$n temperature is very low when $CO_2$ was released. So electrical instrument, magnetic storage equipment and memory semiconductor are electrically or physically injured by cooling effect in a few minutes. So, we intend to find out temperature profile and electrical damage in compartment area, and supply basic d data for research and making standards and code through the full scale experiment. As result of experiment on the damage due to cooling effect from $CO_2$ extinguishing system, i instantaneous discharging temperature. was $-82.5^{\circ}C$ in average. An average temp. in the compartment after discharging $CO_2$ was $-40^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1513-1514
• /
• 2015

전력설비가 열화, 서지에 의해 절연이 파괴되었을 경우 밀폐기기 경우 폭발, 화재를 일으킴으로써 일반인에게 피해를 입히거나 인근 설비로 파급이 확대될 가능성이 있다. 최근 전력설비는 대용량화 추세인 반면 콤팩트 사이즈를 요구하고 있어 절연문제로 인한 폭발 가능성은 더욱 커지고 있다. 이러한 전력설비의 폭발을 방지하고 피해확대를 줄이기 위해 방압변, 순간압력상승 방지장치 등이 설치되고 있으나, 예방에는 한계가 있다. 이에 최근, 국외를 중심으로 전력기기 특히, 지상설치기기의 안전성 확보를 위해 고속투입 접지스위치(Arc Eliminator)를 개발하여 설치 의무화를 고려하고 있다.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.127-128
• /
• 2015

전력사용 증가에 따른 전력망의 확대에 따라 발생할 수 있는 사고와 안전성의 문제도 지속적으로 제기되고 있다. 그 중 화재사고의 발생원인 중 하나인 스파크에 관한 많은 실험적 연구가 존재하나, 수치해석 모델링을 통한 연구는 부족하다. 이 논문에서는 직류회로의 도선이 절단되는 순간 발생하는 스파크 현상을 다루기 위해, 등가회로의 개념을 적용하여 열과 전계 세기를 결합 해석하는 다중물리 해석 기법을 제시한다. 유한요소법을 이용한 수치해석 프로그램을 통하여 데이터를 도출한다.

• Fire Science and Engineering
• /
• v.27 no.5
• /
• pp.19-25
• /
• 2013

The fire took place in the synthetic heat transfer fluid boiler. This study uses simulation to investigate the first, second and third passes and the temperature in the fire burner. The boiler's internal fluid is more or less unsteady due to the out of order inverter. As the operation continues, the flame's flow and speed are unsteady. The synthetic heat transfer fluid leak spouted about 120 kg/min in the form of vapor in the early period of the fire. The flame extended to the second and third passes. The highest temperature of the second and third pass is $1059^{\circ}C$ and $1007^{\circ}C$, respectively. The simulation shows that the temperature is $767^{\circ}C$ in the low part of the third pass. The synthetic heat transfer fluid spouted through the cracked part of the fire box in the first pass and accumulated on the turn table. The temperature rises to $183^{\circ}C$ in the low part of the burner. Therefore, it is expected that the temperature of the interior of the fire box is above $1200^{\circ}C$. The temperature of the burner rises to a maximum level several times in a short period. On account of that, several explosions occur in the fire burner.